WERTHEIM 7000 User manual

7000
Instruction Manual

2
ONLINE
www.wertheim.net.au
EMAIL
[email protected]
2 Year
WARRANTY
Due to the process of continual improvement, minor
changes in product design or features may occur from
what is shown on the packaging.
[email protected]

3
WARNINGS & SAFETY INFORMATION
BEFORE OPERATING THIS MACHINE, PLEASE READ THESE SAFETY INSTRUCTIONS CAREFULLY
For Household Use Only
1. Only use this machine indoors on dry surfaces
2. Turn off the vacuum controls before connecting or disconnecting from the electrical outlet
3. Do not run over power supply cord
4. Do not use machine if the power supply cord is damaged
5. Do not use machine if it has been dropped, damaged, left outdoors or dropped into water
6. Do not pull or carry machine by the power supply cord, use the cord as a handle, close doors
on the cord, pull the cord around sharp corners, run the machine over the cord, or expose the
cord to heated surfaces
7. Do not carry the machine while turned on and in use
8. Do not unplug by pulling on the power supply cord, unplug the cord by grasping the plug, not
the cord
9. Do not handle the machine or the plug with wet hands. Do not use outdoors or on wet surfaces
10. Use only the recommended attachments for this machine
11. Do not put any foreign object into machine openings, or use with blocked openings or restricted
air fl ow
12. Do not expose hair, loose clothing, fi ngers, or other body parts to openings or moving parts of
the machine
13. Do not pick up hot or burning objects
14. Do not pick up fl ammable or combustible materials (lighter fl uid, petrol, kerosene, etc.) or use
in the presence of explosive liquids or vapors
15. Do not pick up toxic material (chlorine, bleach, ammonia, drain cleaner, petrol etc)
16. Do not use machine in an enclosed space fi lled with vapors from oil based paint, paint thinner, some
moth proofi ng surfaces, fl ammable dust, or other explosive toxic vapors
17. Remove plug from electrical outlet before cleaning the machine
18. Not intended for use by persons with reduced physical, sensory or mental capabilities, or lack of
experience or knowledge, unless they have been given supervision or instruction concerning use
of the machine by a person responsible for their safety
19. Keep out of reach of children
20. Store the machine indoors in a cool, dry area
21. Do not modify the earthed plug
22. Do not use for any purpose other than described in this instruction manual
This machine is intended for household use only and not for commercial or industrial use.
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they
do not play with the appliance.
When using your Wertheim vacuum, basic safety precautions should always be observed, including
the following:

4
7000 PARTS
1. On/Off Buttons
2. Cord Retract Button
3. Power Adjustment Indicators
4. Accessories Storage Button
5. Accessories Storage
6. Dust Bag Cover Release Button
7. Power Cord
8. HEPA Filter (Not Visible)
9. Power Handle & Hose
10. Telescopic Tube
11. Powerhead (Height Adjustment)
12. Deluxe Combination Floor Tool
13. Small Dusting Brush
14. Crevice Tool
15. Mini Turbo Brush
16. Blower Attachment
17. Hard Floor Tool
9
OPTIONAL ACCESSORIES
12
15
10
14
11
17
16
6
1
1
4
4
12
8 3
5
7
13

5
ASSEMBLY STEPS
STANDARD ACCESSORIES

6
7000POWERING YOUR WERTHEIM
RETRACTING CORD
Carpet
Variable Height
Adjustment
Hard Floor
CORRECT FLOOR SETTING
looT roolF rof gnitteS daehrewoP rof gnitteS
For max power,
make sure your
powerhead is
turned on.
Refer to page 10 for
Powering your W7000.
1 - 6

7
ADJUST POWER SETTING
ADJUST POWER SETTING
REPLACING YOUR BAG
REPLACING YOUR BAG
CLEANING YOUR MOTOR FILTER
CLEANING YOUR MOTOR FILTER
See page 10 for settings.

8
REPLACING THE HEPA FILTER
ACCESSORIES STORAGE COMPARTMENT

9
CLEARING POWERHEAD OBSTRUCTIONS - RESETTING POWERHEAD
OFF
Be sure to completely
remove all obstructions
before pressing the
reset button.
Make sure the machine
is also disconnected
from the power source.
PROBLEMS AND TROUBLESHOOTING
If a problem occurs it can usually be solved by referring to the checklist below. If your problem
can not be fi xed using these tips, please contact our customer support centre (1800 815 270)
who will be happy to help.
PROBLEM POSSIBLE CAUSE SOLUTION
Motor does not start
or stops No power supply Check cord, plug and socket. If still
inoperative contact
service agent
The dust bag is full, fi lters are
dirty, suction hose or wand
is blocked
Empty the dust bag,
Ensure that the switch
clean or replace fi lters,
remove objects from
hose and wand
on the handle and
powerhead is switched on
Reset button has tripped Make sure the roller is
clean and then press the
reset button (see above)
Roller not rotating
on powerhead Powerhead is not switched on Check the powerhead is switched on
The belt is broken Contact the service agent
No power supply to powerhead
not working
Powerhead
gradually decreases
Suction force

10
ASSEMBLY STEPS - Refer to visual steps on pages 5-9 if required.
The cleaner should be switched off and disconnected from the mains supply before
commencing assembly.
• Connect the hose body connector to the cleaner
• Insert the wand into the powerhead
• Press the release button on the telescopic tube to extend or retract to desired length
• Fit the other end of the telescopic tube to the hand piece
• To detach tube from powerhead, press down on the release pedal with your foot
ACCESSORIES
Your Wertheim 7000 comes with a powerhead, a deluxe combination fl oor tool, a mini turbo
brush and crevice tool, a dust brush and a blower attachment.
OPTIONAL ACCESSORIES
• Hard Floor Tool
POWERING YOUR WERTHEIM 7000
If you are using your machine without the powerhead and are using any of the other tools
you only need to turn on the power for the machine (not the powerhead).
The switch on the handle is used when you have the powerhead on.
The switch on the powerhead allows you to turn off the rotating brush. (You may not want
to change the fl oor head, but are using on a hard fl oor & don’t want the brush rotating).
• Pull the power cord out from the rear of the vacuum and plug into a power socket
(Never extend the power cord further than the yellow mark)
• Press the On/Off button to switch the appliance on
• When you are fi nished using the appliance, unplug from the power socket and press the
power cord retract button to retract the power cord
CORRECT FLOOR SETTING
Deluxe Combination Floor Tool - Has two fl oor settings. One for hard fl oors and the other
for carpeted surfaces. To adjust the setting, press down
on the fl oor tool lever.
ADJUST POWER SETTING
To adjust the suction from the machine, rotate the variable speed dial. MIN setting to reduce
the suction, and MAX setting to increase the suction.

11
EMPTYING YOUR CLEANER
Before emptying, switch ‘OFF’ and unplug the appliance
• An indicator light will illuminate when the dust bag is full
• Pull upwards on the lid release button and lift up the dust bag lid
• Slide out dust bag and replace, then close the lid
CLEANING YOUR FILTERS
• Pull upwards on the lid release button and lift up the dust bag lid
• Slide out dust bag
• Firmly pull the fi lter cover tab to release and remove
• Separate fi lter from fi lter cover and rinse with warm water
Ensure fi lter is completely dry before re-fi tting
REPLACING THE HEPA FILTER
Before replacing fi lters, switch ‘OFF’ and unplug the appliance
• Pull upwards on the lid release button and lift up the dust bag lid
• Unclip and slide out the HEPA fi lter
• Replace the HEPA fi lter and close the dust bag lid
CLEARING POWERHEAD OBSTRUCTIONS - RESETTING POWERHEAD
If the powerhead brushbar is obstructed, it may automatically shut off. If this happens
you will need to clear any obstructing objects and reset the powerhead
• Switch ‘OFF’ and unplug the appliance
• Clear and remove all obstructions caught within the powerhead brushbar
• Press the red button on rear of powerhead to reset
• Return plug into power socket and switch both the appliance and powerhead ‘ON’
to resume cleaning

V3 0412