Weslo Cadence 935 Treadmill User manual

®
USER'S MANUAL
Model No. WCTL26080
Serial No.
Write the serial number in the
space above for future reference.
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
Serial
Number
Decal
QUESTIONS?
As a manufacturer, we are com-
mitted to providing complete
customer satisfaction. If you
have questions, or if there are
missing or damaged parts, we
will guarantee complete satis-
faction through direct assistance
from our factory.
TO AVOID UNNECESSARY
DELAYS, PLEASE CALL DIRECT
TO OUR TOLL-FREE CUSTOMER
HOT LINE. The trained techni-
cians on our Customer Hot Line
will provide immediate assis-
tance, free of charge to you.
CUSTOMER HOT LINE:
1-888-936-4266
Mon.–Fri., 8 a.m.–6:30 p.m. EST
(excluding holidays)
Visit our website at
www.weslo.com
new products, prizes,
fitness tips, and much more!

2
TABLE OF CONTENTS
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
OPERATION AND ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
HOW TO FOLD AND MOVE THE TREADMILL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
MAINTENANCE AND TROUBLE-SHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
CONDITIONING GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover
LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover
Note: A PART LIST and an EXPLODED DRAWING are attached in the center of this manual. Remove the PART
LIST and EXPLODED DRAWING before beginning assembly.
1. It is the responsibility of the owner to ensure
that all users of this treadmill are adequately
informed of all warnings and precautions.
2. Use the treadmill only as described in this
manual.
3. Place the treadmill on a level surface, with 8
feet (2 m) of clearance behind it. Do not place
the treadmill on a surface that blocks any air
openings. To protect the floor or carpet from
damage, place a mat under the treadmill.
4. When choosing a location for the treadmill,
make sure that the location and position per-
mits access to the plug.
5. Keep the treadmill indoors, away from mois-
ture and dust. Do not put the treadmill in a
garage or covered patio, or near water.
6. Do not operate the treadmill where aerosol
products are used or where oxygen is being
administered.
7. Keep children under the age of 12 and pets
away from the treadmill at all times.
8. The treadmill should not be used by persons
weighing more than 250 pounds (115 kg).
9. Never allow more than one person on the
treadmill at a time.
10. Wear appropriate exercise clothing when
using the treadmill. Do not wear loose
clothing that could become caught in the
treadmill. Athletic support clothes are recom-
mended for both men and women. Always
wear athletic shoes. Never use the treadmill
with bare feet, wearing only stockings, or in
sandals.
11. When connecting the power cord (see page 7),
plug the power cord into a surge suppressor
(not included) and plug the surge suppressor
into a grounded circuit capable of carrying 15
or more amps. No other appliance should be
on the same circuit. Do not use an extension
cord.
12. Use only a CUL-listed surge suppressor,
rated at 15 amps, with a 14-gauge cord of five
feet or less in length. Do not use an exten-
sion cord.
13. Keep the power cord and the surge suppres-
sor away from heated surfaces.
14. Never move the walking belt while the power
is turned off. Do not operate the treadmill if
the power cord or plug is damaged, or if the
treadmill is not working properly. (See
BEFORE YOU BEGIN on page 4 if the tread-
mill is not working properly.)
IMPORTANT PRECAUTIONS
WARNING:To reduce the risk of burns, fire, electric shock, or injury to persons, read
the following important precautions and information before operating the treadmill.

3
15. Never start the treadmill while you are stand-
ing on the walking belt. Always hold the
handrails while using the treadmill.
16. The treadmill is capable of high speeds.
Adjust the speed in small increments to
avoid sudden jumps in speed.
17. The pulse sensor is not a medical device.
Various factors, including the user's move-
ment, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
as an exercise aid in determining heart rate
trends in general.
18. Never leave the treadmill unattended while it
is running. Always remove the key when the
treadmill is not in use.
19. Do not change the incline of the treadmill by
placing objects under the treadmill.
20. Do not attempt to raise, lower, or move the
treadmill until it is properly assembled. (See
ASSEMBLY on page 5, and HOW TO FOLD
AND MOVE THE TREADMILL on page 10.)
You must be able to safely lift 45 pounds
(20 kg) in order to raise, lower, or move the
treadmill.
21. When storing the treadmill, make sure that
the storage latch is fully closed.
22. Inspect and tighten all parts of the treadmill
every three months.
23. Never drop or insert any object into any
opening.
24. DANGER:Always unplug the power
cord immediately after use, before cleaning
the treadmill, and before performing the
maintenance and adjustment procedures
described in this manual. Never remove the
motor hood unless instructed to do so by an
authorized service representative. Servicing
other than the procedures in this manual
should be performed by an authorized ser-
vice representative only.
25. This treadmill is intended for in-home use
only. Do not use this treadmill in any com-
mercial, rental, or institutional setting.
WARNING:Before beginning this or any exercise program, consult your physician.
This is especially important for persons over the age of 35 or persons with pre-existing health prob-
lems. Read all instructions before using. ICON assumes no responsibility for personal injury or prop-
erty damage sustained by or through the use of this product.
SAVE THESE INSTRUCTIONS
The decal shown at the right has been placed
on your treadmill. If the decal is missing, or if
it is not legible, please call our Customer
Service Department, toll-free, to order a free
replacement decal (see ORDERING
REPLACEMENT PARTS on the back cover of
this manual). Apply the decal in the location
shown.

4
BEFORE YOU BEGIN
Thank you for selecting the WESLO®CADENCE 935
treadmill. The CADENCE 935 treadmill combines
advanced technology with innovative design to let you
enjoy an excellent form of cardiovascular exercise in
the convenience and privacy of your home. And when
you’re not exercising, the unique CADENCE 935 can
be folded up, requiring less than half the floor space of
other treadmills.
For your benefit, read this manual carefully before
using the treadmill. If you have additional questions,
please call our Customer Service Department toll-free
at 1-888-936-4266, Monday through Friday, 8 a.m.
until 6:30 p.m. Eastern Standard Time (excluding holi-
days). To help us assist you, please note the product
model number and serial number before calling. The
model number of the treadmill is WCTL26080. The
serial number can be found on a decal attached to the
treadmill (see the front cover of this manual for the
location).
Before reading further, please review the drawing
below and familiarize yourself with the labeled parts.
Handrails
Console
Storage Latch
Speed Control
Key/Clip
Circuit Breaker
Walking Belt
Foot Rails
FRONT
BACK
RIGHT SIDE
Rear Roller
Adjustment Bolts Incline Leg
Water Bottle Holder
(Bottle not included)
Accessory Tray

1. Refer to drawing 2 below. Note that the Console
Base (52) and the Right Handrail (60) are connected
to the treadmill by the Wire Harness (76). During
assembly steps 1 through 3, be careful to avoid
pulling on or damaging the Wire Harness.
Refer to drawing 1. With the help of a second per-
son, carefully lay the treadmill on its side. Position
one of the Base Legs (64) on the base of the
Upright (59) as shown. Make sure that the Base Leg
Pads (67) and the Front Wheel (65) are in the indi-
cated positions. Attach the Base Leg with two Base
Leg Bolts (69), two Base Leg Washers (70), and two
Base Leg Nuts (73).
With the help of a second person, carefully turn the
treadmill onto its other side. Assemble the other
Base Leg (64) as described above.
With the help of a second person, carefully raise the
treadmill to the upright position so the Base Legs
(64) are resting flat on the floor.
2. Hold the treadmill firmly with both hands, and lower
the treadmill to the floor. To decrease the possibili-
ty of injury, bend your legs and keep your back
straight.
2
1
5
69
70 67
64
65
59 73
73
76
60
52
Handrail Bolt (71)–2
Upright Bolt (48)–2
Upright Washer
(38)–2
Base Leg Bolt (69)–4
Base Leg Washer
(70)–6
Base Leg Nut
(73)–4 Flange Nut (9)–2 Console Screw (47)–8
ASSEMBLY
Assembly requires two people. Set the treadmill in a cleared area and remove all packing materials. Do not
dispose of the packing materials until assembly is completed. Note: The underside of the walking belt is coated
with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to the top of the
walking belt or the shipping carton. This does not affect treadmill performance. If there is lubricant on top of the
walking belt, wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner. The following tools are
required for assembly: a phillips screwdriver and two adjustable wrenches
(not included).
During assembly, refer to the drawings below to identify the small parts used in assembly.

3. Insert the bracket on the Left Handrail (61) into the
left Upright (59). Whilst a second person holds the
Console Base (52), carefully insert the Right
Handrail (60) into the right Upright (59). Make sure
that the lower ends of the Handrails (61, 60) are
on the inside of the Base Legs (64) (refer to the
inset drawing).
Loosely thread an Upright Bolt (48) with an Upright
Washer (38) into each Upright (59).
Refer to the inset drawing. Insert a Handrail Bolt
(71) with a Base Leg Washer (70) into the right Base
Leg (64) and the Right Handrail (60). Loosely
thread a Flange Nut (9) onto the Handrail Bolt.
Repeat this step with the Left Handrail (not shown).
4. Place the Console Base (52) on the Left and Right
Handrails (61, 60). Insert the excess Wire Harness
(not shown) into the top of the right Upright (59), as
you pull the excess Wire Harness (76) out of the
bottom of the Upright (see drawing 6). Attach the
Console Base with four Console Screws (47).
Tighten all parts used in assembly step 3.
5. Attach the Left Frame Guide (86) and the Frame
Guide Spacer (14) to the left side of the Frame (87)
with four Latch Screws (47) as shown. Note: Be
careful not to overtighten the Screws. Make sure
that the notched end of the Frame Guide is at the
bottom.
6. The console requires two "AA" batteries (not includ-
ed); alkaline batteries are recommended. Open the
Battery Cover (56) as shown. Insert two batteries
into the battery compartment, with the negative (–)
ends of the batteries touching the springs. Close
the battery cover, push up on the battery cover tab,
and then push the tab forward as shown in the inset
drawing. Be sure that the tab locks into place.
5
4
6
14 87
47
86
Notched End
47
61
47
60
59
52
6
38
38 48
52
59 59
61 60 76
Bracket
48
3
Battery Cover Tab
Batteries
56
70
64
60
71
9
7. Make sure that all parts are properly tightened before you use the treadmill. Note: Some parts may be
left over after assembly is completed. Save the included allen wrench for adjusting the walking belt. To protect
the floor or carpet from damage, place a mat under the treadmill.

7
OPERATION AND ADJUSTMENT
THE PERFORMANT LUBETM WALKING BELT
Your treadmill features a walking belt coated with
PERFORMANT LUBETM, a high-performance lubricant.
IMPORTANT: Never apply silicone spray or other
substances to the walking belt or the walking plat-
form. They will deteriorate the walking belt and
cause excessive wear.
HOW TO PLUG IN THE POWER CORD
Your treadmill, like any other type of sophisticated
electronic equipment, can be seriously damaged by
sudden voltage changes in your home’s power.
Voltage surges, spikes, and noise interference can
result from weather conditions or from other appli-
ances being turned on
or off. To decrease the
possibility of your
treadmill being dam-
aged, always use a
surge protector (not
included) with your
treadmill.
Surge protectors are
sold at most hardware
stores and department
stores. Use only a CUL-
listed surge protector,
rated at 15 amps, with
a 14-gauge cord of five
feet or less in length.
This product must be
grounded. If it should
malfunction or break
down, grounding pro-
vides a path of least
resistance for electric
current to reduce the
risk of electric shock. This product is equipped with a
cord having an equipment-grounding conductor and a
grounding plug. Plug the power cord into a surge
protector, and plug the surge protector into an
appropriate outlet that is properly installed and
grounded in accordance with all local codes and
ordinances.
This product is for use on a nominal 120-volt circuit,
and has a grounding plug that looks like the plug illus-
trated in drawing 1 below. A temporary adapter that
looks like the adapter illustrated in drawing 2 may be
used to connect the surge protector to a 2-pole recep-
tacle as shown in drawing 2 if a properly grounded
outlet is not available.
The temporary adapter should be used only until a
properly grounded outlet (drawing 1) can be installed
by a qualified electrician.
The green-colored rigid ear, lug, or the like extending
from the adapter must be connected to a permanent
ground such as a properly grounded outlet box cover.
Whenever the adapter is used it must be held in place
by a metal screw. Some 2-pole receptacle outlet
box covers are not grounded. Contact a qualified
electrician to determine if the outlet box cover is
grounded before using an adapter.
DANGER:Improper connection
of the equipment-grounding conductor can
result in an increased risk of electric shock.
Check with a qualified electrician or service-
man if you are in doubt as to whether the
product is properly grounded. Do not modify
the plug provided with the product—if it will
not fit the outlet, have a proper outlet
installed by a qualified electrician.
1
2
Grounded Outlet Box
Grounded Outlet Box
Grounding Plug
Treadmill Power Cord
Grounding Plug
Grounding Plug
Grounding Pin
Surge Protector
Grounding Pin
Grounding Pin
Adapter
Lug
Metal Screw
Grounded Outlet

8
DIAGRAM OF THE CONSOLE
Clip
Key
Speed Control
Monitor Display Pulse Display
PulseSensor
STEP BY STEP CONSOLE OPERATION
Before operating the console, make sure that the
power cord is properly plugged in. (See HOW TO
PLUG IN THE POWER CORD on page 7.) In addition,
make sure that batteries are installed in the console.
(See step 6 on page 6.) If there is a thin sheet of clear
plastic on the console, remove it.
Step onto the foot rails of the treadmill. Next, find the
clip attached to the key (see the drawing above). Slide
the clip onto your waistband.
Follow the steps below to operate the console.
Insert the key fully into the power switch.
Note: Inserting the key will not turn on the dis-
plays. The displays will turn on when the display
button is pressed or when the walking belt is
started. If you just installed batteries, the displays
will already be on.
Reset the console and start the walking belt.
Move the speed
control to the
RESET posi-
tion. Note:
Each time the
walking belt is
stopped, the speed control must be moved to
the RESET position before the walking belt
can be restarted.
Next, slowly move the speed control until the
walking belt begins to move at slow speed.
Carefully step onto the walking belt and begin
exercising. Change the speed of the walking belt
as desired by moving the speed control.
To stop the walking belt, step onto the foot rails
and move the speed control to the RESET position.
2
1
CAUTION:Before operating the
console, read the following precautions.
• Do not stand on the walking belt when turn-
ing on the power.
• Always wear the clip (see the drawing
above) while operating the treadmill. When
the key is removed from the console, the
walking belt will stop.
• Adjust the speed in small increments.
• To reduce the possibility of electric shock,
keep the console dry. Avoid spilling liquids
on the console and use only a sealable
water bottle.
Mode
Button
Display
Button

9
Follow your progress with the monitor display.
The monitor display
offers six modes that
provide instant exer-
cise feedback:
Speed—This mode shows your speed, in
miles per hour or kilometres per hour.
Time—This mode shows the length of time
you have exercised. Note: If you stop exercis-
ing for ten seconds, the time mode will pause.
Distance—This mode shows the total number
of miles or kilometres you have walked or run,
up to 999.
Fat Calories—This mode shows the approxi-
mate number of fat calories you have burned.
(See FAT BURNING on page 14.)
Calories—This mode shows the approximate
number of calories you have burned.
Scan—This mode displays the other five
modes, for five seconds each, in a repeating
cycle.
When the power is
turned on, the scan
mode will be selected.
One mode indicator
will appear by the
scan icon and another
mode indicator will
show which mode is currently displayed.
If desired, the speed,
time, distance, fat
calories or calories
mode can be individu-
ally selected. Press
the mode button
repeatedly until the
desired mode indicator appears. Make sure that
there is not a mode indicator by the scan icon.
To reset the display, press the display button.
Measure your pulse, if desired.
When you are not
using the pulse
sensor, a “P” will
appear in the pulse
display. To mea-
sure your pulse,
stand on the foot
rails and place your
thumb on the pulse sensor as shown. The pulse
sensor is pressure activated—fully press it down.
Do not press too hard, or the circulation in
your thumb will be restricted, and your pulse
will not be detected. Next, raise your thumb
slightly until the heart-
shaped indicator in the
pulse display flashes
steadily. Hold your
thumb at this level. After
a few seconds, three
dashes will appear in
the display and your pulse will be shown. Hold
your thumb on the sensor for another 15 seconds
for the most accurate reading.
If the displayed pulse appears to be too high or too
low, or if your pulse is not displayed, lift your thumb
off the sensor and allow the display to reset. Press
down again on the sensor as described above.
Make sure that your thumb is positioned as shown,
and that you are applying the proper amount of
pressure to the pulse sensor. Try the sensor sever-
al times until you become familiar with it.
Remember to stand still whilst measuring your
pulse.
Turn off the power.
To turn off the power, simply wait for about six
minutes. If the walking belt is stationary and the
console buttons are not pressed for six minutes,
the power will turn off automatically.
5
43
Indicator
Pulse
Sensor
Mode Indicators

HOW TO SELECT KILOMETRES AND MILES
The console can display distance and speed in either
kilometres or miles. To change the unit of measure-
ment, first UNPLUG THE POWER CORD. Next,
remove the six screws attaching the console to the
console base. Lift the console a few inches, being
careful not to pull on the wires, and turn the console
over. Locate the small switch on the back of the con-
sole. Move the switch upward or downward to select
kilometres or miles. Re-attach the console to the con-
sole base. After changing the unit of measurement,
remove one of the batteries from the console for
about five seconds and then reinsert it. This will
reset the console.
HOW TO CHANGE THE INCLINE OF THE TREADMILL
To vary the intensity of your exercise, the incline of the
treadmill can be changed. There are three different
incline levels. Before changing the incline, remove
the key and unplug the power cord.
To change the incline of the treadmill, first hold the
rear roller end-
cap with one
hand and raise
the back of the
treadmill a few
inches. Using
your other
hand, rotate
the incline leg
to one of the
three incline
positions. The
inset drawing
at the right shows the incline leg rotated to the “max
fat burn” position. This position is ideal for maximum
fat burning. For a less intense fat burning workout,
rotate the incline leg to the “fat burn” position. For aer-
obic exercise, rotate the incline leg to the “aerobic”
position. When you have turned the incline leg to the
desired position, lower the treadmill. Make sure that
the incline leg is resting flat on the floor.
10
HOW TO FOLD AND MOVE THE TREADMILL
HOW TO FOLD THE TREADMILL FOR STORAGE
Before folding the treadmill, unplug the power cord.
Caution: You must be able to safely lift 45 pounds (20
kg) in order to raise, lower, or move the treadmill.
1. Hold the treadmill with your hands in the locations shown
at the right. To decrease the possibility of injury, bend
your legs and keep your back straight. As you raise
the treadmill, make sure to lift with your legs rather
than your back. Raise the treadmill about halfway to the
vertical position.
Screws
Screws
Console
Console
Base
Incline
Leg
Switch

11
2. Move your right hand to the position shown at the right,
and hold the treadmill firmly. Raise the treadmill until the
storage latch locks over the frame guide. If necessary,
turn the incline leg as you raise the treadmill. Make sure
that the storage latch closes fully over the frame
guide.
To protect the floor or carpet from damage, place a
mat under the treadmill. Keep the treadmill out of
direct sunlight. Do not leave the treadmill in the stor-
age position in temperatures above 30° Celsius.
HOW TO MOVE THE TREADMILL
Before moving the treadmill, convert the treadmill to the
storage position as described on page 10. Make sure that
the storage latch is locked fully over the frame guide.
1. Hold the upper ends of the handrails. Place one foot on
one of the front wheels as shown.
2. Tilt the treadmill back until it rolls freely on the front
wheels. Carefully move the treadmill to the desired loca-
tion. Never move the treadmill without tipping it back,
or the base pads may come off. To reduce the risk of
injury, use extreme caution whilst moving the tread-
mill. Do not attempt to move the treadmill over an
uneven surface.
3. Place one foot on the base, and carefully lower the tread-
mill until it is resting in the storage position.
HOW TO LOWER THE TREADMILL FOR USE
1. Hold the upper end of the treadmill with your right hand
as shown. Using your left hand, slide open the storage
latch. Pivot the treadmill until the frame guide and the
foot rail are past the storage latch. If necessary, turn the
incline leg as you raise the treadmill.
2. Hold the treadmill firmly with both hands, and lower the
treadmill to the floor. To decrease the possibility of
injury, bend your legs and keep your back straight.
Opened
Storage
Latch
Incline
Leg
Frame
Guide
Base Leg
Front Wheels
Storage
Latch
Incline
Leg
Frame
Guide
Closed

12
MAINTENANCE AND TROUBLE-SHOOTING
Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and
follow the steps listed. If further assistance is needed, please call our Customer Service Department toll-
free at 1-888-963-4266, Monday through Friday, 8 a.m. until 6:30 p.m. Eastern Standard Time (excluding
holidays).
PROBLEM: The power does not turn on
SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppres-
sor is plugged into a properly grounded outlet (see page 7). Use only a CUL-listed surge sup-
pressor, rated at 15 amps, with a 14-gauge cord of five feet or less in length.
b. After the power cord has been plugged in, make sure that the key is fully inserted into the con-
sole.
c. Check the circuit breaker located on the treadmill
frame near the power cord. If the switch pro-
trudes as shown, the circuit breaker has tripped.
To reset the circuit breaker, wait for five minutes
and then press the switch back in.
PROBLEM: The power turns off during use
SOLUTION: a. Check the circuit breaker located on the treadmill frame near the power cord (see the drawing
above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in.
b. Make sure that the power cord is plugged in.
c. Remove the key from the console. Reinsert the key fully into the console.
d. If the treadmill still will not run, please call our Customer Service Department, toll-free.
PROBLEM: The displays of the console do not function properly
SOLUTION: a. Check the batteries in the console. If the batteries need to be replaced, see assembly step 6 on
page 6. Most problems are the result of drained batteries.
b. If the speed display does not show a correct read-
ing, remove the key and UNPLUG THE POWER
CORD. Remove the screws from the sides and front
of the hood. Carefully remove the hood. Locate the
Reed Switch (19) and the Magnet (18) on the left
side of the Pulley (89). Turn the Pulley until the
Magnet is aligned with the Reed Switch. Make sure
that the gap between the Magnet and the Reed
Switch is about 3mm (1/8”). If necessary, loosen
the Screw (44) and move the Reed Switch slightly.
Retighten the Screw. Re-attach the hood and run
the treadmill for a few minutes to check for a correct
speed reading.
Tripped Reset
Tripped Reset
c
18
19
44
Top
View
3mm 89

13
PROBLEM: The walking belt is off-centre or slips when walked on
SOLUTION: a. If the walking belt has shifted to the left, first
remove the key and UNPLUG THE POWER CORD.
Using the allen wrench, turn the left rear roller adjust-
ment bolt clockwise, and the right bolt counterclock-
wise, 1/4 of a turn each. Be careful not to overtighten
the walking belt. Plug in the power cord, insert the
key and run the treadmill for a few minutes. Repeat
until the walking belt is centred.
b. If the walking belt has shifted to the right, first
remove the key and UNPLUG THE POWER CORD.
Using the allen wrench, turn the left rear roller adjust-
ment bolt counterclockwise, and the right bolt clock-
wise, 1/4 of a turn each. Be careful not to overtighten
the walking belt. Plug in the power cord, insert the
key and run the treadmill for a few minutes. Repeat
until the walking belt is centred.
c. If the walking belt slips when walked on, first
remove the key and UNPLUG THE POWER CORD.
Using the allen wrench, turn both rear roller adjust-
ment bolts clockwise, 1/4 of a turn. When the walking
belt is correctly tightened, you should be able to lift
each side of the walking belt 5 to 7 centimetres off
the walking platform. Be careful to keep the walking
belt centred. Plug in the power cord, insert the key
and run the treadmill for a few minutes. Repeat until
the walking belt is properly tightened.
PROBLEM: The walking belt slows when walked on
SOLUTION: a. Use only a CUL-listed surge suppressor, rated at 15 amps, with a 14-gauge cord of five feet or
less in length.
b. If the walking belt is overtightened, treadmill perfor-
mance may decrease and the walking belt may be
permanently damaged. Remove the key and
UNPLUG THE POWER CORD. Using the allen
wrench, turn both rear roller adjustment bolts counter-
clockwise, 1/4 of a turn. When the walking belt is
properly tightened, you should be able to lift each
side of the walking belt 5 to 7 centimetres (2 to 3
inches) off the walking platform. Be careful to keep
the walking belt centred. Plug in the power cord,
insert the key and run the treadmill for a few minutes.
Repeat until the walking belt is properly tightened.
c. I If the treadmill still will not run, please call our Customer Service Department, toll-free.
b
c
a
Rear Roller
Adjustment Bolts
5—7 cm
b

14
CONDITIONING GUIDELINES
The following guidelines will help you to plan your
exercise program. Remember—these are general
guidelines only. For more detailed exercise informa-
tion, obtain a reputable book or consult your physi-
cian.
EXERCISE INTENSITY
Whether your goal is to burn fat or to strengthen your
cardiovascular system, the key to achieving the
desired results is to exercise with the proper intensity.
The proper intensity level can be found by using your
heart rate as a guide. To find the proper heart rate for
you, first find your age at the top of the chart below
(ages are rounded off to the nearest ten years). Next,
find the two numbers below your age. The two num-
bers are your “training zone.”
To measure your heart rate during exercise, use the
pulse sensor on the console. If your heart rate is too
high or too low, adjust the speed of the treadmill as
needed.
Fat Burning
To burn fat effectively, you must exercise at a relatively
low intensity level for a sustained period of time.
During the first few minutes of exercise, your body
uses easily accessible carbohydrate calories for ener-
gy. Only after the first few minutes does your body
begin to use stored fat calories for energy. If your goal
is to burn fat, adjust the speed and incline of the tread-
mill until your heart rate is near the low end of your
training zone. (See pages 8 to 9.)
Aerobic Exercise
If your goal is to strengthen your cardiovascular sys-
tem, your exercise must be “aerobic.” Aerobic exercise
is activity that requires large amounts of oxygen for
prolonged periods of time. This increases the demand
on the heart to pump blood to the muscles, and on the
lungs to oxygenate the blood. For aerobic exercise,
adjust the speed and incline of the treadmill until your
heart rate is near the middle of your training zone. (See
pages 8 to 9.)
WORKOUT GUIDELINES
Each workout should include the following three parts:
Warming Up
Start each workout with 5 to 10 minutes of stretching
and light exercise. A proper warm-up increases your
body temperature, heart rate, and circulation in prepa-
ration for exercise.
Training Zone Exercise
After warming up, increase the intensity of your exer-
cise until your pulse is in your training zone for 20 to
60 minutes. (During the first few weeks of your exer-
cise program, do not keep your pulse in your training
zone for longer than 20 minutes.) Breathe regularly
and deeply as you exercise—never hold your breath.
Cool-down
Finish each workout with 5 to 10 minutes of stretching
to cool down. This will increase the flexibility of your
muscles and will help prevent post-exercise problems.
EXERCISE FREQUENCY
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest
between workouts. After a few months, you may com-
plete up to five workouts each week if desired. The
key to success is to make exercise a regular and
enjoyable part of your everyday life.
WARNING:Before beginning
this or any exercise program, consult your
physician. This is especially important for
individuals over the age of 35 or individuals
with pre-existing health problems.
The pulse sensor is not a medical device.
Various factors, including your movement,
may affect the accuracy of heart rate readings.
The sensor is intended only as an exercise aid
in determining heart rate trends in general.

SUGGESTED STRETCHES
The correct form for several basic stretches is shown in the
drawings at the right. Move slowly as you stretch—never
bounce.
1. Toe Touch Stretch
Stand with your knees bent slightly and slowly bend forward
from your hips. Allow your back and shoulders to relax as you
reach down toward your toes as far as possible. Hold for 15
counts, then relax. Repeat 3 times. Stretches: Hamstrings,
back of knees and back.
2. Hamstring Stretch
Sit with one leg extended. Bring the sole of the opposite foot
toward you and rest it against the inner thigh of your extended
leg. Reach toward your toes as far as possible. Hold for 15
counts, then relax. Repeat 3 times for both legs. Stretches:
Hamstrings, lower back and groin.
3. Calf/Achilles Stretch
With one leg in front of the other, reach forward and place
your hands against a wall. Keep your back leg straight and
your back foot flat on the floor. Bend your front leg, lean for-
ward and move your hips toward the wall. Hold for 15 counts,
then relax. Repeat 3 times for both legs. To cause further
stretching of the achilles tendons, bend your back leg as well.
Stretches: Calves, achilles tendons and ankles.
4. Quadriceps Stretch
With one hand against a wall for balance, reach back and
grasp one foot with your other hand. Bring your heel as close
to your buttocks as possible. Hold for 15 counts, then relax.
Repeat 3 times for both legs. Stretches: Quadriceps and hip
muscles.
5. Inner Thigh Stretch
Sit with the soles of your feet together and your knees out-
ward. Pull your feet toward your groin area as far as possible.
Hold for 15 counts, then relax. Repeat 3 times. Stretches:
Quadriceps and hip muscles.
1
2
3
4
5
15

PART LIST—Model No. WCTL26080 R0102A
Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. See the back cover of
the user’s manual for information about ordering replacement parts.
Key No. Qty. Description
1 2 Incline Leg Bolt
2 6 Incline Leg Pad
3 2 Incline Leg
4 2 Incline Leg Plate
5 2 Incline Leg Bushing
6 2 Incline Leg Bracket
7 1 Left Foot Rail
8 3 8” Cable Tie
9 2 Flange Nut
10 1 Tie Clamp
11 4 Belt Guide Screw
12 14 Fastner
13 4 Leg Bracket Screw
14 1 Frame Guide Spacer
15 1 Motor Hood
16* 1 Motor/Pulley/Flywheel/Fan
17 1 Motor Belt
18 1 Magnet
19 1 Reed Switch
20 1 Reed Switch Clip
21 4 Hood Anchor
22 16 Anchor Screw/Base Pad Screw
23 2 Frame Pivot Nut
24 1 Motor
25 1 Pulley/Flywheel/Fan
26 1 Motor Tension Bolt
27 1 Motor Tension Washer
28 1 Motor Star Washer
29 1 Motor Tension Nut
30 1 Motor Pivot Bolt
31 1 Wire Clip
32 1 Controller
33 1 Electronics Bracket
34 1 Power Cord
35 1 Grommet
36 1 Circuit Breaker
37 1 Front Roller Adj. Bolt
38 10 Upright Washer/Adj. Washer
39 2 Upright Spacer
40 1 Right Endcap
41 2 Latch Spring
42 1 Storage Latch
43 1 Latch Bracket
44 1 Wire Clamp
45 2 Cage Nut
46 1 Plug Cover
47 16 Console Screw/Latch Screw
48 2 Upright Bolt
49 8 Console Base Screw
Key No. Qty. Description
50 1 Left Endcap
51 1 Choke
52* 1 Console Base Assembly
53 1 Motor Pivot Nut
54 1 Speed Control Knob
55 1 Speed Potentiometer
56 1 Battery Cover
57 2 Belt Guide
58 1 Key/Clip
59 1 Upright Base
60 1 Right Handrail
61 1 Left Handrail
62 2 Frame Pivot Bolt
63 2 Wheel Nut
64 2 Base Leg
65 2 Front Wheel
66 2 Wheel Bolt
67 4 Base Leg Pad
68 1 Allen Wrench
69 4 Base Leg Bolt
70 6 Base Leg Washer
71 2 Handrail Bolt
72 8 Walking Platform Screw
73 4 Base Leg Nut
74 2 Base Leg Cap
75 1 Upright Grommet
76 1 Wire Harness
77 10 Ground Screw
78 1 Wrench Clip
79 2 Frame Pivot Washer
80 2 5/16” Flat Washer
81 1 Right Foot Rail
82 1 Interface Bracket
83 1 Belly Pan
84 8 Isolator
85 1 Rear Belly Pan
86 2 Frame Guide
87 1 Frame
88 1 Incline Rod
89 1 Front Roller/ Pulley
90 1 Walking Platform
91 1 Walking Belt
92 1 Latch Decal
93 1 Rear Roller
94 1 Ground Wire
95 2 Rear Roller Guard
96 2 Endcap Bolt
# 1 14” White Wire, Male/Female
# 1 User’s Manual

34
REMOVE THIS EXPLODED DRAWING
AND PART LIST FROM THE MANUAL
Save this EXPLODED DRAWING and PART LIST for future reference.
Note: Specifications are subject to change without notice. For information
about ordering replacement parts, see the back cover of the User’s Manual.

7
17
26 27 28
29
24
25
30
16*
22
47
47 47
15
71
70
84
57
11
5
6
13
13
6
88
5
22
39
2
3
1
2
2
4
4
2
2
2
1
3
38
86
47 14
12
47
62
39
62 65
66
63
67
70
64
67
74
73
73
22
73
79
79
42
22
22
9
9
47
47
48
48
75
22
76
69
70
66 65
74
63
64
67
22
67
22
70 71
60
61
45
12
12
49
53
19
22
49
51
32
36
22
21
35
37
38
22
12
72
72
84
12
85
22
83
47
86
23
18
22
21
21
90
91
7
93
20
89
34
87
82
92
72
69
58
59
76
81
38
38
81
54
52* 55 49 56
49
49
68
77
38
78
77 38
80
46
50
40
49
44
38
38
33
41
84
84
8
10
49 43
38
EXPLODED DRAWING—Model No. WCTL26080 R0102A

Part No. 167069 R0102A Printed in Canada © 2002 ICON Health & Fitness, Inc.
WESLO is a registered trademark of ICON Health & Fitness, Inc.
ORDERING REPLACEMENT PARTS
To order replacement parts, simply call our Customer Service Department toll-free at 1-888-963-4266 Monday
through Friday, 8 a.m. until 6:30 p.m. Eastern Standard Time (excluding holidays). To help us assist you, please
be prepared to give the following information when calling:
• The MODEL NUMBER of the product (WCTL26080)
• The NAME of the product (WESLO®CADENCE 935 treadmill)
• The SERIAL NUMBER of the product (see the front cover of this manual)
• The KEY NUMBER AND DESCRIPTION OF THE PART(S) (see the EXPLODED DRAWING and PART LIST
attached in the center of this manual).
LIMITED WARRANTY
ICON OF CANADA INC., (ICON), warrants this product to be free from defects in workmanship and material,
under normal use and service conditions, for a period of one (1) year from the date of purchase. This warranty
extends only to the original purchaser. ICON's obligation under this warranty is limited to replacing or repair-
ing, at ICON's option, the product at one of its authorized service centers.All products for which warranty claim
is made must be received by ICON at one of its authorized service centers with all freight and other trans-
portation charges prepaid, accompanied by sufficient proof of purchase.All returns must be pre-authorized by
ICON. This warranty does not extend to any product or damage to a product caused by or attributable to
freight damage, abuse, misuse, improper or abnormal usage or repairs not provided by an ICON authorized
service center, to products used for commercial or rental purposes, or to products used as store display mod-
els. No other warranty beyond that specifically set forth above is authorized by ICON.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in connection
with the use or performance of the product or damages with respect to any economic loss, loss of property, loss
of revenues or profits, loss of enjoyment or use, costs of removal, installation or other consequential damages
of whatsoever nature. Some provinces do not allow the exclusion or limitation of incidental or consequential
damages. Accordingly, the above limitation may not apply to you. The warranty extended hereunder is in lieu
of any and all other warranties and any implied warranties of merchantability or fitness for a particular purpose
is limited in its scope and duration to the terms set forth herein. Some provinces do not allow limitations on how
long an implied warranty lasts. Accordingly, the above limitation may not apply to you.
This warranty gives you specific legal rights. You may also have other rights which vary from province to
province or so specified by the retailer of your equipment.
ICON OF CANADA, 900 de l’Industrie, St. Jérôme, QC J7Y 4B8