Weslo WCTL19809.0 User manual

USER'S MANUAL
Serial Number
Decal
Model No. WCTL19809.0
Serial No.
Write the serial number in the space
above for future reference.
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
QUESTIONS?
If you have questions, or if parts
are damaged or missing, PLEASE
CONTACT OUR CUSTOMER
SERVICE DEPARTMENT DI-
RECTLY.
CALL TOLL-FREE:
1-888-936-4266
Mon.–Fri., 8:00 until 17:00 ET
(excluding holidays)
OR E-MAIL US:
[e-mail]
www.weslo.com

TABLE OF CONTENTS
WARNINGDECALPLACEMENT ..............................................................2
IMPORTANTPRECAUTIONS .................................................................3
BEFOREYOUBEGIN .......................................................................5
ASSEMBLY ...............................................................................6
OPERATIONANDADJUSTMENT ............................................................11
HOWTOFOLDANDMOVETHETREADMILL ..................................................16
TROUBLESHOOTING ......................................................................18
EXERCISEGUIDELINES ...................................................................20
PARTLIST ...............................................................................22
EXPLODEDDRAWING .....................................................................24
ORDERINGREPLACEMENTPARTS ..................................................BackCover
LIMITEDWARRANTY...............................................................BackCover
WESLO is a registered trademark of ICON IP, Inc.
2
WARNING DECAL PLACEMENT
The decal shown here has been applied in the loca-
tion shown. If the decal is missing or illegible, call
the telephone number on the front cover of this
manual and request a free replacement decal.
Apply the decal in the location shown. Note: The
decal may not be shown at actual size.

3
1. Before beginning any exercise program, con-
sult your physician. This is especially impor-
tant for persons over the age of 35 or persons
with pre-existing health problems.
2. It is the responsibility of the owner to ensure
that all users of this treadmill are adequately
informed of all warnings and precautions.
3. Use the treadmill only as described.
4. Place the treadmill on a level surface, with at
least 8 ft. (2.4 m) of clearance behind it and 2
ft. (0.6 m) on each side. Do not place the
treadmill on any surface that blocks air open-
ings. To protect the floor or carpet from dam-
age, place a mat under the treadmill.
5. Keep the treadmill indoors, away from mois-
ture and dust. Do not put the treadmill in a
garage or covered patio, or near water.
6. Do not operate the treadmill where aerosol
products are used or where oxygen is being
administered.
7. Keep children under the age of 12 and pets
away from the treadmill at all times.
8. The treadmill should be used only by persons
weighing 250 lbs. (113 kg) or less.
9. Never allow more than one person on the
treadmill at a time.
10. Wear appropriate exercise clothes when
using the treadmill. Do not wear loose clothes
that could become caught in the treadmill.
Athletic support clothes are recommended for
both men and women. Always wear athletic
shoes. Never use the treadmill with bare feet,
wearing only stockings, or in sandals.
11. When connecting the power cord (see page
11), plug the power cord into a surge sup-
pressor (not included) and plug the surge
suppressor into a grounded circuit capable of
carrying 15 or more amps. No other appliance
should be on the same circuit. Do not use an
extension cord.
12. To decrease the possibility of your treadmill
being damaged, always use a surge suppres-
sor with your treadmill. To purchase a surge
suppressor call the telephone number on the
front cover of this manual.
13. Failure to use a properly functioning surge
suppressor could result in damage to the con-
trol system of the treadmill. If the control sys-
tem is damaged, the walking belt may change
speed, accelerate, or stop unexpectedly,
which may result in a fall and serious injury.
14. Keep the power cord and the surge suppres-
sor away from heated surfaces.
15. Never move the walking belt while the power
is turned off. Do not operate the treadmill if
the power cord or plug is damaged, or if the
treadmill is not working properly. (See TROU-
BLESHOOTING on page 18 if the treadmill is
not working properly.)
16. Read, understand, and test the emergency
stop procedure before using the treadmill (see
HOW TO TURN ON THE POWER on page 13).
17. Never start the treadmill while you are stand-
ing on the walking belt. Always hold the
handrails while using the treadmill.
18. The treadmill is capable of high speeds.
Adjust the speed in small increments to avoid
sudden jumps in speed.
19. Never leave the treadmill unattended while it
is running. Always remove the key, unplug
the power cord, and switch the reset/off cir-
cuit breaker to the off position when the
treadmill is not in use. (See the drawing on
page 5 for the location of the circuit breaker.)
WARNING: To reduce the risk of serious injury, read all important precautions and in-
structions in this manual and all warnings on your treadmill before using your treadmill. ICON as-
sumes no responsibility for personal injury or property damage sustained by or through the use of
this product.
IMPORTANT PRECAUTIONS

4
20. Do not attempt to raise, lower, or move the
treadmill until it is properly assembled. (See
ASSEMBLY on page 6, and HOW TO FOLD
AND MOVE THE TREADMILL on page 16.)
You must be able to safely lift 45 lbs. (20 kg)
to raise, lower, or move the treadmill.
21. When folding or moving the treadmill, make
sure that the storage latch is fully closed.
22. Never insert any object into any opening on
the treadmill.
23. Inspect and properly tighten all parts of the
treadmill regularly.
24. DANGER: Always unplug the power
cord immediately after use, before cleaning the
treadmill, and before performing the mainte-
nance and adjustment procedures described in
this manual. Never remove the motor hood un-
less instructed to do so by an authorized ser-
vice representative. Servicing other than the
procedures in this manual should be performed
by an authorized service representative only.
25. This treadmill is intended for in-home use
only. Do not use this treadmill in a commer-
cial, rental, or institutional setting.
SAVE THESE INSTRUCTIONS

5
Thank you for selecting the new WESLO®CADENCE
25 treadmill. The CADENCE 25 treadmill combines ad-
vanced technology with innovative design to make
your workouts at home more effective and enjoyable.
And when youʼre not exercising, the CADENCE 25
treadmill can be folded up, requiring less than half the
floor space of other treadmills.
For your benefit, read this manual carefully before
using the treadmill. If you have questions after read-
ing this manual, please see the front cover of this man-
ual. To help us assist you, note the product model
number and serial number before contacting us. The
model number and the location of the serial number
decal are shown on the front cover of this manual.
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
BEFORE YOU BEGIN
Handrail
Storage Latch
Console
ey/Clip
Incline Leg/Pin
Walking Belt
Hood
Wheel
Foot Rail
Idler Roller
Adjustment Bolts
Water Bottle Holder*
Power Cord
Reset/Off
Circuit Breaker
*Water bottle is not included.

6
ASSEMBLY
Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials; do not
dispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking
belt is coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to
the top of the walking belt or the shipping carton. This does not affect treadmill performance. If there is lubricant
on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner.
Assembly requires the included hex key and your own Phillips screwdriver , two
adjustable wrenches , and wire cutters .
Use the drawings below to identify the assembly hardware. The number in parentheses below each drawing is
the key number of the part, from the PART LIST near the end of the manual. The number after the parentheses
shows the quantity needed for assembly. Note: If a part is not in the parts bag, check to see if it is preat-
tached to one of the parts to be assembled. Extra hardware may be included. To avoid damaging plastic
parts, do not use power tools for assembly.
M10 x 110 Bolt (1)–2
M10 x 58mm Bolt (2)–4
M8 x 70mm Bolt (3)–4
M4.2 x 19mm
Screw (4)–4
M6 x 58mm Bolt (6)–4
M5 x 16mm
Screw (5)–2 M4.2 x 16mm
Screw (7)–6
M6 Washer
(11)–4
M8.5
Washer (13)–4
M10 Washer
(14)–6
M6 Nut (15)–4
M10 Nut (16)–4
M10 Star
Washer (9)–2
M8 Star
Washer (10)–4
M5 Star
Washer (12)–2

7
2. Slide the two Wheel Housings (62) onto the Base (52)
with the head of the M10 x 62mm Bolts (35) on the out-
side as shown. Attach each Wheel Housing with two M6 x
58mm Bolts (6), two M6 Washers (11), and two M6 Nuts
(15).
2
52
611
62 15
11
6
62
35
35
15
1. Have a second person hold the Base (52) in the position
shown.
Identify the Left Upright (53) (the Right Upright [54] has a
large hole near the lower end).
Hold the Left Upright (53) so the bend is in the posi-
tion shown. Insert two M10 x 58mm Bolts (2) into the
bracket on the Left Upright. Attach the Left Upright to
the Base (52) with the M10 x 58mm Bolts, two M10
Washers (14), and two M10 Nuts (16). Do not tighten
the Nuts yet.
Attach the Right Upright (54) to the Base (52) in the
same way.
52
53
54 16
1
216
14
14
14
2
Large
Hole
Bend

8
3. With the help of a second person, raise the Uprights
(53, 54) so the Base (52) is flat on the floor as shown.
Next, position the front of the treadmill Frame (51) be-
tween the Uprights.
See the inset drawing. Locate the wire inside of the
lower end of the Right Upright (54). Secure the wire to
the Wire Harness (98) using the included plastic tie.
Then, pull the upper end of the wire until the end of the
Wire Harness is extending from the indicated hole in the
upper end of the Right Upright.
Have a second person lift and hold the front end of the
Frame (51). Hold a Frame Spacer (23) between the Right
Upright (54) and the Frame. Attach the Right Upright and
the Frame Spacer to the Frame with an M10 x 110mm
Bolt (1), an M10 Washer (14), and an M10 Star Washer
(9).
Repeat this step on the left side of the treadmill. 9
23
52
14
1
54
51
Large
Hole
Hole
3
53
98 54
Tie
98
4. Turn the Console Assembly (91) face-down. Be careful
not to scratch the face of the Console Assembly.
Identify the Right Handrail (55), which has a large hole
in one side.
Attach the Right Handrail (55) to the Console Assembly
(91) with two M4.2 x 19mm Screws (4), an M5 x 16mm
Screw (5), and an M5 Star Washer (12).
12
91
4
Large Hole
5
55
4
Wire

9
6. Hold the Console Assembly (91) near the Right Upright
(54). Touch the Right Handrail to discharge any static.
Insert the end of the Wire Harness (98) into the hole in
the bottom of the Right Handrail (55) and out of the
large hole in the side. Next, Insert the end of the Wire
Harness through the two looped plastic ties.
Press the end of the Wire Harness (98) into the indi-
cated connector on the back of the Console Assembly
(91). See the inset drawing. The end of the Wire
Harness should slide easily into the connector and
snap into place. If it does not, turn the end of the Wire
Harness and try again. IF THE CONNECTOR IS NOT
INSERTED PROPERLY, THE CONSOLE MAY BE
DAMAGED WHEN THE POWER IS TURNED ON.
Plastic
Ties
Connector
91
55
98
54
5. Place the Left Handrail (56) on the Console Assembly
(91). Attach the Left Handrail to the Console Assembly
with two M4.2 x 19mm Screws (4), an M5 x 16mm
Screw (5), and an M5 Star Washer (12). 12
91
4
5
56
6
5
98
7. Insert the slack in the Wire Harness (98) down into the
Right Upright (54). Then, tighten the two plastic ties
around the Wire Harness, and cut off the ends of the
plastic ties.
98 Plastic
Ties
54
7

9. Carefully lower the Handrails (55, 56) to the floor. Center
the Frame (51) between the Handrails, and tighten the
four M10 x 58mm Bolts (2) (see step 1). Then, raise the
Handrails back to the vertical position.
See the inset drawing. Attach the Latch Assembly (102)
to the Left Upright (53) with two M4.2 x 16mm Screws
(7). Make sure that the Latch Assembly is oriented
as shown.
See HOW TO CHANGE THE INCLINE OF THE TREAD-
MILL on page 15. Adjust the incline of the treadmill as
desired.
10. Make sure that all parts are properly tightened before you use the treadmill. Note: Extra hardware may
be included. eep the included hex keys in a secure place; the large hex key is used to adjust the walking
belt (see page 19). To protect the floor or carpet, place a mat under the treadmill.
102
53
7
8. Set the Console Assembly (91) on the Right Upright (54)
and the Left Upright (not shown). Next, start four M8 x
70mm Bolts (3) with four M8.5 Washers (13) and four
M8 Star Washers (10) (only two of each are shown) into
the Right Upright and the Left Upright. Then, tighten all
four Bolts.
Insert the slack in the Wire Harness (98) down into the
Right Upright (54).
Attach the Console Back (93) to the Console Assembly
(91) with four M4.2 x 16mm Screws (7). Make sure that
the Wire Harness (98) is in the indicated slot in the
Console Back and that no wires are pinched.
91
54
7
7
10
98
Slot
13
3
93
8
9
55, 56
51 2
10