Wesper WKRV01 User manual

Setup & Care Guide
WESPERTM SLEEP KIT | Model #: WKRV01
Safety and Handling
This device has been tested to comply with IEC standards IEC 6061-1, IEC 6061-1-2 and
IEC 6061-11. WESPER is an electrical appliance and safety precautions should always
be followed to reduce the risk of burns, fire, electric shock or injury, including the
following precautions:
Wear And Care:
For the avoidance of doubt, WESPER is not a medical device and is not intended to
replace any medical diagnosis or treatment recommended to you by your physician.
When caring for your WESPER, follow these tips:Do not use cleaners or any liquid to
clean your WESPER. Only place on dry surfaces. Do not place on a surface wet from
water or cleaning solvents.Do not place or store the product in an area subject to
excess dust. Do not expose your WESPER to direct sunlight for extended periods of time.
Do not leave your WESPER near an open flame. Do not place or store the product where
it can fall or be pulled into a tub or sink. If you experience any kind of discomfort or
notice signs of skin irritation where your WESPER touches your skin, please discontinue
use and contact our support team. Do not attempt to disassemble or service your
WESPER yourself. Protect your WESPER from any shocks or impacts. Do not expose your
WESPER to extremely high temperatures above 104° F (40° C) or low temperatures
below 23° F (-5° C). Battery life: 12 hours (150mAH) Use only a certified USB power
adapter (not included).Power supply should be Limited Power Supply (LPS).
Important Safety Information:
Take the time to read, understand and follow all safety information contained in this
user manual before using your WESPER. Please save these instructions for future
reference.
CAUTION:
Contains small parts. Keep out of reach of children.Use this appliance only for its
intended use as described in this manual. Do not operate this device if it has a damaged
cord, plug, cable or housing.
Batteries Precautions:
To reduce the risk of electric shock and to avoid possible risks associated with
hazardous voltage, which if not avoided could result in death or serious injuries.
Read, understand and follow the following safety instructions:This product contains a
lithium-ion battery. Use only the included wireless charging mat to recharge your
patches. Do not attempt to charge the device using another wireless charging device.
There is a risk of explosion if batteries are not handled in the correct way. The batteries
are not designed to be replaced. Damage inflicted on the battery could cause an
explosion and/or fire. Do not dismantle, open or shred the battery. Do not expose the
battery to heat or fire. Avoid storage in direct sunlight. Do not short-circuit the battery.
Disposal And Recycling Information
For disposal and recycling of WESPER, please contact your local recycling authority. If
you have any questions on the matter, please contact our support team at
[e-mail].
FCC Declaration of Conformity Compliance statement
FCC ID: includes 2AAQS-ISP1507 or 2AAQS-ISP1807
This equipment complies with Part 15 of the FCC Rules. Operation is subject to two
conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired
operation. As defined in Section 2.909 of the FCC Rules,the responsible party for this
device is: Wesper Inc., 234 5th Ave, New York, NY 10001, USA. Tel #:[phone]
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment and mees the FCC radio frequency (RF) Exposure Guidelines.
End users must follow the specific operating instructions for satisfying RF exposure
compliance.This transmitter must not be co-located or operating in conjunction with
any other antenna or transmitter.
Federal Communications Commission Radio Frequency Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates,uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions,may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment causes harmful interference to radio or
television reception,which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following
measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.
Modifications
Wesper is not responsible for any radio interference caused by unauthorized
modifications to this equipment. Changes or modifications not expressly approved by
Wesper could void the user’s authority and warranty to operate the equipment.
Silicone Adhesives
WESPER’s adhesives are made from medical grade silicone. Avoid use if you have any
known allergy to silicone.The adhesives have been thoroughly tested and should not
cause skin irritation. However, if skin irritation develops or any other symptoms occur,
discontinue use and contact us. In case of irritation, wash skin thoroughly with soap and
water. Seek medical attention if symptoms persist. The adhesives should not be used on
wounded skin. If eye contact occurs,hold the eye open and immediately rinse with water
for at least 15 minutes. Obtain medical attention if soreness or redness persist.
Customer Service Web Contact
If your product is not working properly and your troubleshooting is unsuccessful, please
contact WESPER technical support at www.wesper.co/contact-us. Additional answers
to your product and technical questions can be found at [e-mail]
Wesper Inc. Customer Relations at [e-mail].
Changes To These Terms
We reserve the right to update, change or replace any of the terms contained in this
document or in other WESPER documentation by posting updates and/or changes to
our website, www.wesper.co. It is your responsibility to check our website from time to
time for any updates or changes, as they are binding on you.
© 2021 Wesper Inc. Any unauthorized copying, duplicating, or other reproduction of the
contents hereof is prohibited without written consent from Wesper Inc. All rights
reserved. Wesper Inc., 234 5th Ave, New York, NY 10001, USA.
PCK000001-REV02

Get Started Preparing For Your Test
Apply a new set of adhesive backings:
3 -Align the adhesive over the shape of
the patch and press firmly.
1 - Make sure the back of the patch is
clean and dry.
2 - Remove one of the adhesive liners
using the pull tab.
1 - Connect the charger to an outlet
with the cable provided
4 - Repeat application on the second
patch.
Having trouble?
Find frequently asked questions, troubleshooting tips, and more
at wesper.co/faq
5 - Open the app and start a new test,
following the in-app instructions.
Sweet dreams!
2 - Make sure the charger and back of
patches are clean and free of any
debris.
3 - Place the patches onto the charger.
Confirm the blue corner charging LEDs
are illuminated. If they aren't, gently
move the patches around until they are
to ensure charging.
4 - Charge the patches for at least 3
hours.
Depending on your patch model, the
corner charging LED may turn off when
charging is complete or remain on.
5 - Install the Wesper app from
the App Store and create an account.
We'll take it from there!