Westermo DDW-142 User manual

www.westermo.com
Wolverine
DDW-142/DDW-242
Industrial Ethernet Extender
WeOS

3
6642-22501
General information
Legal information
The contents of this document are provided “as is”. Except as required by applicable law,
no warranties of any kind, either express or implied, including, but not limited to, the
implied warranties of merchantability and fitness for a particular purpose, are made in
relation to the accuracy and reliability or contents of this document. Westermo reserves
the right to revise this document or withdraw it at any time without prior notice.
Under no circumstances shall Westermo be responsible for any loss of data or income or
any special, incidental, and consequential or indirect damages howsoever caused.
More information about Westermo can be found at the following Internet address:
www.westermo.com
Software tools
Related software tools are available in the folder software tools under technical support
on the Westermo website.
License and copyright for included Free/Libre Open Source Software
This product includes software developed by third parties, including Free/Libre Open
Source Software (FLOSS). The specific license terms and copyright associated with the
software are included in each software package respectively. Please visit the product web
page for more information.
Upon request, the applicable source code will be provided. A nominal fee may be charged
to cover shipping and media. Please direct any source code request to your normal sales
or support channel.
WeOS Management Guide
This product runs WeOS (Westermo Operation System). Instructions for quick start,
configuration, factory reset and use of USB port are found in the WeOS Management
Guide at www.westermo.com.

4
6642-22501
Safety information
Before installation:
Read this manual completely and gather all information on the unit. Make sure that
you understand it fully. Check that your application does not exceed the safe operating
specifications for this unit.
This unit should only be installed by qualified personnel.
This unit should be built-in to an apparatus cabinet, or similar, where access is restricted
to service personnel only. This unit may have hot surfaces when used in high ambient
temperature.
The power supply wiring must be sufficiently fused, and if necessary it must be possible
to disconnect manually from all power supply. Ensure compliance to national installation
regulations. This unit uses convection cooling. Make sure that the unit is installed such
as its ambient temperature is within its specified maximum/minimum temperature. This
unit uses convection cooling. To avoid obstructing the airflow around the unit, follow the
spacing recommendations (see Cooling section).
Warning
Prevent access to hazardous voltage by disconnecting the unit from power supply.
Do not open connected unit. Hazardous voltage may occur within this unit when
connected to power supply.
Note that this unit can be connected to two different power sources.
When this unit is operated at an ambient temperature above +60°C (+140°F),
forced ventilation is required to not exceed Touch Temperature Limits according
to UL/IEC/EN 60950-1. A recommended airflow 32CFM (61m3/h) located 17cm
(7") below the unit is a minimum requirement.
To reduce the risk of fire, use only No. 26 AWG or larger telecommunication line
cord.
For more information see General safety 100-5001.
Care recommendations
Follow the care recommendations below to maintain full operation of unit and to fulfill
the warranty obligations.
• This unit must not be operating with removed covers or lids.
• Do not attempt to disassemble the unit. There are not any user serviceable
parts inside.
• Do not drop, knock or shake the unit. Rough handling above the specification
may cause damage to internal circuit boards.
• Do not use harsh chemicals, cleaning solvents or strong detergents to clean the
unit.
!

5
6642-22501
• Do not expose the unit to any kind of liquids (rain, beverages, paint etc). The
unit is not waterproof. Keep the unit within the specified humidity levels. .
• Do not use or store the unit in dusty or dirty areas,connectors as well as
other mechanical part may be damaged.
• Do not cover or bring mechanical force to the ventilation membrane on the
back of the unit.
If the unit is not working properly, contact the place of purchase, nearest Westermo
distributor office or Westermo Tech support. A readily accessible disconnect device shall
be incorporated external to the equipment
Maintenance
No maintenance is required, as long as the unit is used as intended within the specified
conditions.
Product disposal
This symbol means that the product shall not be treated
as unsorted municipal waste when disposing of it. It needs
to be handed over to an applicable collection point for
recycling electrical and electronic equipment.
By ensuring this product is disposed of correctly, you will
help to reduce hazardous substances and prevent potential
negative consequences to both environment and human
health, which could be caused by inappropriate disposal.

6
6642-22501
Agency approvals and standards compliance
Type Approval / Compliance
EMC EN 61000-6-1, Immunity residential environments
EN 61000-6-2, Immunity industrial environments
EN 61000-6-3*, Emission residential, commercial and light-industrial environments
EN 61000-6-4, Emission industrial environments
EN 50121-4, Railway signalling and telecommunications apparatus
IEC 62236-4, Railway signalling and telecommunications apparatus
Safety UL/IEC/EN 60950-1, IT-equipment
Marine* DNV GL rules for classification – Ships and offshore units
Environmental NEMA TS 2, Traffic Controller Assemblies with NTCIP Requirements**
*Only DDW-142 and DDW-242, 24-48 VDC
**Only DDW-x42-12VDC
FCC Part 15.105
Notice:
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
… Reorient or relocate the receiving antenna
… Increase the separation between the equipment and receiver
… Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected
… Consult the dealer or an experienced radio/TV technician for help.
Corrosive
environment
Notice:
This product has been successfully tested in a corrosion test according to IEC 60068-
2-60, method 3. This means that the product meets the requirements to be placed in an
environment classified as ISA-S71.04 class G3.
Note! If the product is placed in a corrosive environment, it is important that all unused
connector sockets are protected with a suitable plug in order to avoid corrosion attacks
on the gold plated pins in connectors.
Simplified EU declaration of conformity
Hereby, Westermo declares that the equipment is in compliance with EU directives. The
full EU declaration of conformity and other detailed information are available at the
respective product page at www.westermo.com. .

7
6642-22501
Type tests and environmental conditions
Electromagnetic Compatibility
Environmental
phenomena
Basic
standard
Description Test levels
ESD EN 61000-4-2 Enclosure contact ± 6 kV
Enclosure air ± 8 kV
Fast transients EN 61000-4-4 Power port ± 2 kV
Ethernet ports ± 2 kV
SHDSL ports ± 2 kV
RS-232 port ± 2 kV
Status out / Digital in ± 2 kV
Earth port ± 1 kV
Surge EN 61000-4-5 Power port L-L: ±0.5 kV, 2 Ω, 18 μF
L-E: ±0.5 kV, 12 Ω, 9 μF
L-E: ±2 kV, 42 Ω, 0.5 μF
L-L: ±1 kV, 42 Ω, 0.5 μF
Ethernet ports L-E: ±2 kV, 2 Ω
SHDSL ports L-E: ±2 kV, 42 Ω, 0.5 μF
RS-232 port L-E: ±2 kV, 2 Ω
Status out / Digital in L-E: ±2 kV, 42 Ω, 0.5 μF
Pulse magnetic field EN 61000-4-9 Enclosure 300 A/m
Radiated RF immunity EN 61000-4-3 Enclosure 20 V/m 80% AM, 1 kHz sine, 80 – 1000 MHz
12 V/m 80% AM, 1 kHz sine, 1000 – 2700 MHz
10 V/m 80% AM, 1kHz sine, 2700 – 6000 MHz
Conducted RF
immunity
EN 61000-4-6 Power port 10 V, 80% AM, 1 kHz sine; 0.15 – 80 MHz
Ethernet ports 10 V, 80% AM, 1 kHz sine; 0.15 – 80 MHz
SHDSL ports 10 V, 80% AM, 1 kHz sine; 0.15 – 80 MHz
RS-232 port 10 V, 80% AM, 1 kHz sine; 0.15 – 80 MHz
Status out / Digital in 10 V, 80% AM, 1 kHz sine; 0.15 – 80 MHz
Earth port 10 V, 80% AM, 1 kHz sine; 0.15 – 80 MHz
Voltage dips
and interruption
EN 61000-4-29 DC Power port 10 ms, interruption
500 ms, 30% reduction
200 ms, 60% reduction
+20 above & –20% below rated voltage
Radiated RF emission CISPR 16-2-3
ANSI C63.4
(FCC part 15)
Enclosure Class B
Conducted RF
emission
CISPR 16-2-1 Power port Class B
Class B
Ethernet ports Class B
Class B
Dielectric strength EN 60950-1 Power port to other
isolated ports
2000 Vrms 50 Hz 1 min
Ethernet ports to all
other isolated ports
1500 Vrms 50 Hz 1 min
RS-232 port to all
other isolated ports
SHDSL ports to all
other isolated ports
Status out / Digital
in port to all other
isolated ports

8
6642-22501
Environmental
Temperature EN 60068-2-1
EN 60068-2-2
Operating DDW-x42: -40 to +70°C (-40 to +158°F)
DDW-x42-12VDC: -40 to +74°C (-40 to +165°F)
Storage & Transport -40 to +85ºC (-40 to +185ºF)
Humidity EN 60068-2-30 Operating 5 to 95% relative humidity
Storage & Transport 5 to 95% relative humidity
Corrosive gases* IEC 60068-2-60 Operating Method 3, 21 days**
Altitude Operating 2 000 m / 70 kPa
Service life Operating 10 years
Reliability prediction
(MTBF)
Operating 437,000 hours (MIL-HDBK- 217F2, GB, 25°C)
Vibration IEC 60068-2-64
(random)
Operating 5 – 20 Hz: 2 m²/s³
20 – 500 Hz: – 3 dB/oct
3 axis = 3 * 30 min
Shock IEC 60068-2-27 Operating 6 ms 1000 m/s²
6 directions, 3 shocks/direction
Bump IEC 60068-2-27 Operating 11 ms 100 m/s²
6 directions, 100 shocks/direction
Packing
Enclosure material EN 60950-1 Zinc (fire enclosure)
Dimension W x H x D Without connectors 52.5 x 100 x 101 mm
With connectors 52.5 x 119 x 101 mm
Weight 0.8 kg
Degree of protection EN 60529 Enclosure IP40
Cooling Convection
Mounting Enclosure Horizontal on 35 mm DIN-rail
* Only DDW-142 and DDW-242, 24-48 VDC
**Method 3, 21 days corresponds to Harsh Industrial Environment G3 which is defined in ANSI/ISA 17.04: 2015

9
6642-22501
Description
Functional description
The Wolverine DDW-142 and DDW-242 allow effective Ethernet networks to be
created over long distances up to 15 km (9.3 mi) at data rates up to 15.3 Mbit/s on
a single twisted pair cable. By using two pairs “bonded” this rate can be doubled up
to 30.6 Mbit/s. The integral switch allows two Ethernet devices to be attached and
an RS-232 port allows for a legacy piece of equipment to be incorporated into the IP
network.
The operating system (WeOS) in DDW-142 and DDW-242 can deliver unique security
functionality for this class of product as well as allowing the product to form part of
a resilient multimedia ring network using the Westermo FRNT protocol or industry
standard STP/RSTP.
WeOS has been developed to provide industrial networking solutions and contains
amazing serial connectivity capability – from being able to simulate an old AT modem,
convert Modbus RTU to TCP or encapsulate serial data into an IP packet.
DDW-142 supports the layer 2 features in WeOS while DDW-242 also supports all layer
3 features, for more details please see the WeOS datasheet.
DDW-142 and DDW-242 are incredibly flexible and easy to use. A basic point-to-point
or multidrop network can be created without the need for any kind of configuration.
However, if a more complex solution requires some kind of network configuration, the
web based setup is simple to use. A CLI interface is also provided making the unit easy
for networking professionals to quickly master. Once the system is configured, an easy
solution is also available for the maintenance engineer – USB backup and restore means
that stored configurations can be automatically downloaded from a USB stick.
DDW-142 and DDW-242 are often used in applications on railways, roads or with utilities
where failure could result in significant costs. All Westermo products are designed with
high MTBF in mind to improve operational reliability and also give long service life. Even
features like the SHDSL diagnostics and management allow indication of line degradation,
allowing planned maintenance. As the unit is designed for these applications, Westermo
also ensure that testing is carried out to ensure the unit can operate at extremes of
temperature, EMC and vibration and still provide robust communications.

10
6642-22501
Interface specifications
Power
Rated voltage DDW-x42: 24 to 48 VDC
DDW-x42-12VDC: 12 to 48 VDC
Operating voltage DDW-x42: 19 to 60 VDC
DDW-x42-12VDC: 9.8 to 60 VDC
Rated current DDW-x42:
245 mA (405 mA) @ 24 VDC (with 500 mA USB load)
124 mA (200 mA) @ 48 VDC (with 500 mA USB load)
DDW-x42-12VDC:
475 mA (765 mA) @ 12 VDC (with 500 mA USB load)*
245 mA (405 mA) @ 24 VDC (with 500 mA USB load)
124 mA (200 mA) @ 48 VDC (with 500 mA USB load)
Rated frequency DC
Inrush current, I²t DDW-x42:
10.6 mA²s @ 24 VDC
24.7 mA²s @ 36 VDC
42.4 mA²s @ 48 VDC
DDW-x42-12VDC:
89 mA²s @ 12 VDC*
18 mA²s @ 48 VDC
Startup current* 2 x Rated current
Polarity Reverse polarity protected
Redundant power input Ye s
Isolation to All other
Connection Detachable screw terminal
Connector size 0.2 – 2.5 mm² (AWG 24 – 13)
Connect the unit using at least 18 AWG (0.75 mm²) wiring
Shielded cable Not required
* External supply current capability for proper start-up.

11
6642-22501
RS-232
Electrical specification EIA RS-232
Data rate 300 bit/s – 115.2 kbit/s
Data format 7 or 8 data bits, Odd, even or none parity, 1 or 2 stop bits
Protocol Transparent, optimised by packing algorithm
Circuit type SELV
Transmission range 15 m / 49 ft
Isolation to Power, SHDSL, Ethernet
Galvanic connection to USB, Console
Connection RJ-45 according to EIA-561
Shielded cable Recommended
Conductive housing Ye s
Number of ports 1
Ethernet TX
Electrical specification IEEE std 802.3. 2005 Edition
Data rate 10 Mbit/s, 100 Mbit/s, manual or auto
Duplex Full or half, manual or auto
Circuit type TNV-1
Transmission range Up to 150 m, with CAT5e cable or better
Isolation to All other
Connection RJ-45, auto MDI/MDIX
Shielded cable Not required, except when installed in Railway applications as
signalling and telecommunications apparatus and located close
to rails.*
Conductive housing Ye s
Number of ports 2
* To minimise the risk of interference, a shielded cable is recommended when the cable is located inside 3 m
boundary to the rails and connected to this port. The cable shield should be properly connected (360°) to an
earthing point within 1 m from this port. This earthing point should have a low impedance connection to the
conductive enclosure of the apparatus cabinet, or similar, where the unit is built-in. This conductive enclosure
should be connected to the earthing system of an installation and may be directly connected to the protective
earth.
Console
Electrical specification LVTTL/LVCMOS-level
Data rate 115.2 kbit/s
Data format 8 data bits, none parity, 1 stop bit, no flow control
Circuit type SELV
Connection 2.5 mm jack, use Westermo cable 1211-2027

12
6642-22501
USB
Electrical specification USB 2.0 host interface
Data rate Up to 12 Mbit/s (full-speed mode)
Circuit type SELV
Maximum supply current 500 mA
Connection USB receptacle connector type A
I/O / Relay output
Maximum voltage/current 60 VDC / 80 mA
Connect resistance Max 30 Ω
Isolation to All other
Connection Detachable screw terminal
Connector size 0.2 – 2.5 mm² (AWG 24 – 13)
I/O / Digital in
Maximum voltage / load current 60 VDC / 2 mA
Voltage levels Logic one >12 V, Logic zero <1V
Isolation to All other
Connection Detachable screw terminal
Connector size 0.2 – 2.5 mm² (AWG 24 – 13)
SHDSL
Electrical specification ITU-T G.991.2 Annex B
Data rate 32 kbit/s to 30.4 Mbit/s with bonding
Protocol EFM according to IEEE 802.3-2005
Transmission range According to ITU-T G.991.2 depending on line quality
Isolation to All other
Connection Detachable screw terminal
Connector size 0.2 – 2.5 mm² (AWG 24 – 13)
Shielded cable Not required
Number of ports 2

13
6642-22501
Location of interface ports and LED’s
LED Indicators
Power connection
I/O connection
SHDSL connection
RS-232 Connection
Position Signal Direction* Description
No. 1 DSR Out Data Set Ready
No. 2 DCD Out Data Carrier Detect
No. 3 DTR In Data Terminal Ready
No. 4 SG – Signal Ground, not chassis ground
No. 5 RD Out Receive Data
No. 6 TD In Transmit Data
No. 7 CTS Out Clear To Send
No. 8 RTS In Request To Send
Female
Pin 1Pin 8
* Direction relative this unit.
Ethernet connection TX (2 ports)
Position Direction* Description
No.1 In/Out Transmitted/Received data
No. 2 In/Out Transmitted/Received data
No. 3 In/Out Transmitted/Received data
No. 4 Not Connected
No. 5 Not Connected
No. 6 In/Out Transmitted/Received data
No. 7 Not Connected
No. 8 Not Connected
* Direction relative this unit.
USB
Position Direction* Description
No.1 Out VBUS
No. 2 In/Out D–
No. 3 In/Out D+
No. 4 Out GND
Shield In/Out Connected to protective earth
* Direction relative this unit.

14
6642-22501
Power connection
1
2
3
4
4-position Product marking Direction Description
No. 1 +DC1 Input Supply voltage input DC1
No. 2 +DC2 Input Supply voltage input DC2
No. 3 -COM Input Common
No. 4 -COM Input Common
This unit supports redundant power connection. The positive inputs are +DC1 and +DC2, the negative input for
both supplies are –COM. Connect the primary voltage (e.g. +24 VDC) to the +DC1 pin and return to one of the
–COM pins on the power input.
Connection to console port
The console port can be used to connect to the CLI
(Command Line Interface).
The following steps needs to be taken
1. Connect the serial diagnostic cable to the console port
(use only Westermo cable 1211-2027).
2. Connect cable to your computer (USB port, if drivers are needed they can be downloaded
from our Web page).
3. Use a terminal emulator and connect with correct speed and format (115200, 8N1)
to the assigned port.
For more information about the CLI, see the WeOS management guide.
I/O connection
Cable 1211-2027
Bottom view
Accessories
Description Art no
Westermo console cable 1211-2027
RJ45 to DB9 cable 1211-2210
Console port
Position Direction* / description
No.1 In / out / GND
No. 2 Out / Tx
No. 3 In / Rx
* Direction relative to this unit.

15
6642-22501
I/O connection
1
2
3
4
4-position Product marking Direction Description
No. 1 Status + Output Alarm relay (status) contact
No. 2 Status – Output Alarm relay (status) contact
No. 3 Digital in + Input Digital in +
No. 4 Digital in – Input Digital in –
The Status output is a potential free, opto-isolated normally closed solid-state relay.
This can be configured to monitor various alarm events within the unit, see WeOS Management Guide.
An external load in series with an external voltage source is required for proper functionality.
For voltage/current ratings, see Interface Specification section.
The Digital in is an opto-isolated
digital input which can be used
to monitor external events.
For voltage/current ratings, see
Interface Specification section:
DDW-142
External
Load
Status
V
VDigital In
+
1
2
3
4
–
SHDSL
1
2
Position Direction* Description
No.1 In/Out 2-wire Receive/Transmit SHDSL
No. 2 In/Out 2-wire Receive/Transmit SHDSL
* Direction relative this unit.

16
6642-22501
URS1
DDW-142 and
DDW-142-12VDC
DDW-242 and
DDW-242-12VDC
LED indicators
LED Status Description
ON OFF Unit has no power.
GREEN All OK, no alarm condition.
RED Alarm condition, or until unit has started
up. (Alarm conditions are configurable, see
WeOS Management Guide).
FLASH Location indicator ("Here I am!"). Activated
when connected to IPConfig Tool, or upon
request from Web or CLI.
DC1 OFF Unit has no power.
GREEN Power OK on DC1.
RED Power failure on DC1.
DC2 OFF Unit has no power.
GREEN Power OK on DC2.
RED Power failure on DC2.
FRNT OFF FRNT disabled.
GREEN FRNT OK.
RED FRNT Error.
BLINK Unit configured as FRNT focal point.
RSTP OFF RSTP disabled.
GREEN RSTP enabled.
BLINK Unit elected as RSTP/STP root switch.
USR1
(only DDW-242)
OFF
Configurable, see WeOS Management
Guide.
GREEN
RED
LNK
SHDSL ports
Link indicator
Port 1–2
OFF No DSL link.
GREEN DSL link established.
GREEN FLASH DSL link negotiation.
YELLOW Port alarm and no link. Or if FRNT or RSTP
mode, port is blocked.
SHDSL ports
Quality indicator
Port 1–2
All OFF No DSL link.
3 RED Signal to noise value below 3 dB.
Unstable DSL link.
1 GREEN Signal to noise value 3–5 dB.
Marginal DSL link.
2 GREEN Signal to noise value 6–9 dB.
Normal DSL link.
3 GREEN Signal to noise value above 9 dB.
Strong DSL link.
RD OFF No serial data received.
GREEN FLASH Serial data received.
TD OFF No serial data transmitted.
GREEN FLASH Serial data transmitted.
YELLOW FLASH Indicate error on RS-422/485 bus.
Copper ports
Port 1–2
OFF No link.
GREEN Link established.
GREEN FLASH Data traffic indication.
YELLOW Port alarm and no link. Or if FRNT, RSTP or
Link Aggregation mode, port is blocked.

17
6642-22501
Mounting
These units should be mounted on 35 mm DIN-rail, which is horizontally mounted inside
an apparatus cabinet or similar. It is recommended that the DIN-rail is connected to
ground. Snap on mounting, see figure.
Mounting the product with integrated DIN-clip:
Removal
Cooling
These unit use convection cooling. To avoid
obstructing the airflow around the unit, use minimum
spacing 25 mm (1.0") above/below and 10 mm (0.4")
left/right the unit.
Spacing is recommended for the use of unit in full
operating temperature range and service life. When
this unit is operated at an ambient temperature
above +60°C (+140°F), refer to the Safety warnings
on page 4.
10mm 10mm
Removing the product with integrated DIN-clip:
Press down the support at the back of the unit using
a screwdriver. See figure.

18
6642-22501
Configuration
Configure the unit via web browser
The unit can easily be configured via a web browser. Open the link http://192.168.2.200
in your web browser, and you will be prompted with a Login screen, where the default
settings for Username and Password are:
Username: admin
Password: westermo
Once you have logged in, you can use the extensive integrated help function describing
all configuration options. Two common task when configuring a new switch is to assign
appropriate IP settings, and to change the password of the admin account. The password
can be up to 64 characters long, and should consist of printable ASCII characters (ASCII
33-126); 'Space' is not a valid password character.
Getting Started
This product runs Westermo Operating System (WeOS) which provides several
management tools that can be used for configuration of the unit.
• IPConfig tool
This is a custom Westermo tool used for discovery of attached Westermo units.
• Web
Configuration of the unit using the web browser.
• CLI
Configuration of the unit via the Command Line Interface.
If the computer is located in the same subnet as the switch you can easily use a web
browser to configure the unit. Within the web you can configure most of the available
functions.
For advanced network settings and more diagnostic information, please use the CLI.
Detailed documentation is available in the chapter ”The Command Line Management
Tool” in the WeOS management guide.
Factory default IP address: 192.168.2.200
Netmask: 255.255.255.0
Gateway: Disabled
Note! If you are not sure about the subnet – consult your network administrator.

19
6642-22501
Cable factory reset on DDW-142 and DDW-242
It is possible to set the unit to factory default settings by using a standard Ethernet RJ-45
cable.
1. Power off the unit and disconnect all cables.
2. Connect an Ethernet cable between Ethernet ports 1 and 2. The unit needs to be
connected directly by an Ethernet cable i.e., not via a hub or switch. Use a straight cable –
not a cross-over cable, when connecting the ports.
3. Power on the unit.
4. Wait for the unit to start-up. Control that the ON LED is flashing red. The ON LED
flashing indicates that the unit is now ready to be reset to factory default. You now
have the choice to go ahead with the factory reset, or to skip factory reset and boot
as normal.
• Go ahead with factory reset:
Acknowledge that you wish to conduct the factory reset by unplugging the Ethernet
cable. The ON LED will stop flashing. This initiates the factory reset process*, and
the unit will restart with factory default settings. When the switch has booted up,
the ON LED will show a green light, and is now ready to use.
• Skip the factory reset:
To skip the factory reset process, just wait for approximately 30 seconds (after the
ON LED starts flashing RED) without unplugging the Ethernet cable. The switch will
conduct a normal boot with the existing settings.
* Note Do not power off the unit while the factory reset process is in progress.
Referring documents
Type Description Document number
Management Guide Westermo OS management guide 6101-3201
Dimensions
Measurements are stated in millimeters.
92 ±1
Min 4mm
Max 7,5mm
34
±1
96 ±1
52 ±1
100
±1

REV. O 6642-22501 2018-05 Westermo Teleindustri AB, Sweden
Westermo • SE-640 40 Stora Sundby, Sweden
Tel [phone] Fax [phone]
E-mail: [e-mail]
www.westermo.com