Westermo SDW-541-F1G-T4G User manual

©Westermo Teleindustri AB
www.westermo.com
User Guide
6644-2240
Industrial Ethernet
5-port Switch
SDW-500
SERIES
SDW-541-F1G-T4G
SDW-550-T5G

2
6644-2240
Legal information
The contents of this document are provided “as is”. Except as required by applicable
law, no warranties of any kind, either express or implied, including, but not limited to,
the implied warranties of merchantability and fitness for a particular purpose, are made
in relation to the accuracy and reliability or contents of this document. Westermo
reserves the right to revise this document or withdraw it at any time without prior
notice.
Under no circumstances shall Westermo be responsible for any loss of data or income
or any special, incidental, and consequential or indirect damages howsoever caused.
More information about Westermo can be found at the following Internet address:
http://www.westermo.com

3
6644-2240
Safety
Before installation:
Read this manual completely and gather all information on the unit. Make sure
that you understand it fully. Check that your application does not exceed the safe
operating specifications for this unit.
This unit should only be installed by qualified personnel.
This unit should be built-in to an apparatus cabinet, or similar, where access is
restricted to service personnel only.
The power supply wiring must be sufficiently fused, and if necessary it must be
possible to disconnect manually from the power supply. Ensure compliance
to national installation regulations.
This unit uses convection cooling.To avoid obstructing the air flow around the
unit, follow the spacing recommendations (see Installation section).
Before mounting, using or removing this unit:
Prevent access to hazardous voltage by disconnecting the unit from power supply.
Warning! Do not open connected unit. Hazardous voltage may occur within this
unit when connected to power supply.
Class 1 Laser Product
Do not look directly into fibre optical fibre port or any connected fibre although
this unit is designed to meet the Class 1 Laser regulations.
Care recommendations
Follow the care recommendations below to maintain full operation of unit and to fulfil
the warranty obligations.
This unit must not be operating with removed covers or lids.
Do not attempt to disassemble the unit. There are no user serviceable parts inside.
Do not drop, knock or shake the unit, rough handling above the specification may cause
damage to internal circuit boards.
Do not use harsh chemicals, cleaning solvents or strong detergents to clean the unit.
Do not paint the unit. Paint can clog the unit and prevent proper operation.
Do not expose the unit to any kind of liquids (rain, beverages, etc). The unit is not
waterproof. Keep the unit within the specified humidity levels.
Do not use or store the unit in dusty, dirty areas, connectors as well as other mechanical
part may be damaged.
If the unit is not working properly, contact the place of purchase, nearest Westermo
distributor office or Westermo Tech support.
Fibre connectors are supplied with plugs to avoid contamination inside the optical port.
As long as no optical fibre is mounted on the connector, e.g. for storage, service or
transportation, should the plug be applied.
!
!
!

4
6644-2240
Note. Fibre Optic Handling
Fibre optic equipment needs special treatment. It is very sensitive to dust and dirt. If
the fibre will be disconnected from the modem the protective hood on the transmitter/
receiver must be connected. The protective hood must be kept on during transportation.
The fibre optic cable must also be handle the same way.
If this recommendation is not, it jeopardises the warranty.
Cleaning of the optical connectors
In the event of contamination, the optical connectors should be cleaned by the use of
forced nitrogen and some kind of cleaning stick.
Recommended cleaning fluids:
• Methyl-, ethyl-, isopropyl- or isobutyl-alcohol
• Hexane
• Naphtha
Maintenance
No maintenance is required, as long as the unit is used as intended within the specified
conditions.
SPECIAL CONDITION FOR SAFE USE
Ambient temperature:
This unit is designed for use in extreme ambient temperature conditions according to
the following: –40 ºC to +74 ºC (–40 ºF to +165 ºF)

5
6644-2240
Type Approval / Compliance
EMC EN 50121-4, Railway applications – Electromagnetic compatibility – Emission
and immunity of the signalling and telecommunications apparatus
EN 61000-6-1, Immunity residential environments
EN 61000-6-2, Immunity industrial environments
EN 61000-6-4, Emission industrial environments
Safety EN/IEC/UL 60950-1, IT-equipment
Marine DNV GL rules for classification – Ships and offshore units
Environmental NEMA TS 2-2003
DNV GL rules for classification
Type Temperature Humidity Vibration EMC Enclosure
SDW-541-F1G-T4G
SDW-550-T5G D B B B A/IP21
Corrosive
environment
Notice:
This product has been successfully tested in a corrosion test according to
IEC 60068-2-60, method 3. This means that the product meets the requirements
to be placed in an environment classified as ISA-S71.04 class G3 and G4.
Note! If the product is placed in a corrosive environment, it is important that all
unused connector sockets are protected with a suitable plug in order to avoid
corrosion attacks on the gold plated pins in connectors.
Agency approvals and standards compliance

6
6644-2240
Declaration of Conformity
Westermo Teleindustri AB
Declaration of Conformity
Org.nr/
Postadress/Postal address
Tel.
Telefax
Postgiro
Bankgiro
Corp. identity number
Registered office
S-640 40 Stora Sundby 016-428000 016-428001 52 72 79-4 5671-5550 556361-2604 Eskilstuna
Sweden Int+46 16428000 Int+46 16428001
The manufacturer
Westermo Teleindustri AB
SE-640 40 Stora Sundby, Sweden
Herewith declares that the product(s)
Type of product Model Art no
Industrial Ethernet switch SDW-550-T5G 3644-2001
SDW-541-F1G-T4G 3644-2020
is in conformity with the following EU directive(s).
No Short name
2014/30/EU Electromagnetic Compatibility (EMC)
2014/35/EU Low Voltage Directive (LVD)
2011/65/EU Restriction of the use of certain hazardous substances in electrical and electronic
equipment (RoHS)
References of standards applied for this EU declaration of conformity.
No Title Issue
EN 61000-6-1 Electromagnetic compatibility – Immunity for residential
environments
2007
EN 61000-6-2 Electromagnetic compatibility – Immunity for industrial
environments
2005
EN 61000-6-4 Electromagnetic compatibility – Emission for industrial
environments
2007
EN 50121-4 Railway applications – Electromagnetic compatibility – Emission
and immunity of the signalling and telecommunications apparatus
2015
EN 60950-1 Information technology equipment -- Safety -- General
requirements
2006
+A11:2009
+A1: 2010
+A12:2011
+A2: 2013
EN 50581 Technical documentation for the assessment of electrical and
electronic products with respect to the restriction of hazardous
substances
2012
The last two digits of the year in which the CE marking was affixed: 16
Pierre Öberg
Technical Manager
19
th
May 2016

7
6644-2240
Type tests and environmental conditions
Environmental phenomena Basic standard Description Test levels
ESD EN 61000-4-2 Enclosure Contact: ±6 kV
Air: ±8 kV
Fast transients EN 61000-4-4 Power port ±2 kV
Signal ports ±2 kV
Surge EN 61000-4-5 Power port Line to earth: ±2 kV
Line to line: ±1 kV
Signal ports Line to earth: ±2 kV
Line to line: ±1 kV
Power frequency magnetic field EN 61000-4-8 Enclosure 300 A/m; 0, 16.7, 50 Hz
Pulsed magnetic field EN 61000-4-9 Enclosure 300 A/m
Radiated RF immunity EN 61000-4-3 Enclosure 20 V/m @ (80 – 2700) MHz
10 V/m @ (2700 – 6000) MHz
1 kHz sine, 80% AM
Conducted RF immunity EN 61000-4-6 Power port 10 V, 80% AM, 1 kHz; (0.15 – 80) MHz
Signal ports 10 V, 80% AM, 1 kHz; (0.15 – 80) MHz
Radiated RF emission CISPR 16-2-3 Enclosure Class B (30 – 6000 MHz)
ANSI C63,4
(FCC Part 15)
Class B (30 – 6500 MHz)
Conducted RF emission CISPR 16-2-1 Power port Class B
Signal ports Class B
Dielectric strength EN 60950-1 Power interface to all other 1.5kV AC @ 60s duration
TX signal interface to all other 1.5kV AC @ 60s duration
TX shield interface to all other 1.5kV AC @ 60s duration
Environmental
Temperatures EN 60068-2-1
EN 60068-2-2
Operating –40 to +74 °C (–40 to +165 °F)
Storage and transport –50 to +85 °C (–58 to +185 °F)
Relative humidity EN 60068-2-30 Operating 5 to 95 % (non-condensing)
Storage and transport 5 to 95 % (condensation allowed
outside packaging)
Altitude Operating 2 000 m/70 kPa
Service life Operating 10 year
Reliability prediction (MTBF) MIL-HDBK-217F Operating SDW-541-F1G-T4G: 1.182.000 hours
SDW-550-T5G: 1.121.000 hours
Vibration IEC 60068-2-6
(sine)
Operating 5–9 Hz ±6 mm
9–500 Hz ±2 g
Shock IEC 60068-2-27 Operating 15 g, 11 ms
Mechanical
Enclosure UL94 Plastic Flammability Class V-0
Dimension W x H x D 34 x 123 x 121 mm
Weight 0.2 kg
Mounting DIN-rail
Degree of protection EN 60529 Enclosure IP21
Cooling Convection
Configuration
Auto configured (auto-negotiation) or manually setting of speed and duplex of individual TX port, by DIP-switches. Port
mirror function is possible to set with DIP-switch. With the port mirror function active the switch will copy all outgoing
traffic to port 1. This can be used to monitor all traffic going out from the switch. Packets may be discarded if the total
throughput exceeds the port speed of port 1.

8
6644-2240
Description
The SDW-541-F1G-T4G is an unmanaged 5-port switch with one SFP fibre port
supporting 100 Mbit/s or Gbit Ethernet, and four copper ports supporting 10/100 Mbit/s
or Gbit Ethernet. The Westermo range of 100 Mbit or Gbit Small Form-factor Pluggable
(SFP) transceivers are available as multimode, singlemode or Bi-Di transceivers with
distance up to 120 km.
The SDW-550-T5G is an unmanaged 5-port
switch with five copper ports, all supporting 10
Mbit/s, 100 Mbit/s or Gbit Ethernet. Both are
designed for easy use in heavy duty industrial,
maritime and rail trackside applications. The
units support 802.1Q long packets which allow
all standard industrial Ethernet protocols to
be used.
The units are designed for use in industrial
applications with dual 9.6 to 57.6 VDC power
input. The unique “tri-galvanic” isolation
provides isolation between all ports, power
supply and between each chassis screen
avoiding ground loop currents. The IP21
rating ensures that the unit can be installed in
locations where condensed water may occur.
Only industrial grade components are used
which gives an MTBF of 1.182.000 hours for
the SDW-541-F1T4G and 1.121.000 hours for
the SDW-550-T5G and thus ensures a long
service life. A wide operating temperature
range of –40 to +74 °C (–40 to +165 °F) can
be achieved with no moving parts.
The units have been tested both by Westermo and external test houses to meet EMC,
isolation, vibration and shock standards, all to the highest levels suitable for heavy
industrial, trackside and maritime environments.
Network diagnostics are simplified with the inclusion of port mirroring on one port
allowing data flow through the switch to be monitored using a network analyzer. All
five ports can have data rate and flow control locked by DIP switch which can eliminate
problems with old legacy Ethernet equipment that is unable to support auto negotiation.

9
6644-2240
Interface specifications
Power
Operating voltage Rated: 12 to 48 VDC
Operating: 9.6 to 57.6 VDC
Rated current SDW-541-F1G-T4G: 12-48 VDC; 260–65mA
SDW-550-T5G: 12-48 VDC; 260–65mA
Rated frequency DC
Inrush current, I2t 22.7·10-3 A2s @ 48 VDC
Startup current* 2 x Rated current
Polarity Reverse polarity protected
Redundant power input Ye s
Isolation to All other
Connection Detachable screw terminal
Connector size 0.2 – 2.5 mm2 (AWG 24 – 12)
Shielded cable Not required
* External supply current capability for proper start-up
Ethernet TX
Electrical specification IEEE std 802.3. 2005 Edition
Data rate 10 Mbit/s, 100 Mbit/s, 1000 Mbit/s manual or auto
Duplex Full or half, manual or auto
Circuit type TNV-1
Transmission range Up to 150 m with CAT5e cable or better*
Isolation to All other
Connection RJ-45, auto MDI/MDI-X
Shielded cable Not required, except when installed in Railway applications as
signalling and telecommunications apparatus and located close
to rails.**
Conductive housing Ye s
Number of ports SDW-541-F1G-T4G: 4
SDW-550-T5G: 5
* Refer to Safety section.
** To minimise the risk of interference, a shielded cable is recommended when the cable is located inside 3 m
boundary or the cable is longer than 30 m and inside 10 m boundary to the rails and connected to this port.
Ethernet SFP pluggable connections (FX or TX) (SDW-541-F1G-T4G)
Electrical specification IEEE std 802.3. 2005 Edition
Data rate 100 Mbit/s or 1000 Mbit/s transceivers supported
Duplex Full or Auto, depending on transceiver
Transmission range Depending on tranceiver
Connection SFP slot holding fibre transceiver or copper transceiver
Number of ports SDW-541-F1G-T4G: 1

10
6644-2240
Connections
Power connection
Network
fibre connection
Network
RJ-45 connection
LED indicators
Available models:
… SDW-541-F1G-T4G 10/100/1000Base-T/TX: 4 ports, 100/1000Base-FX: 1 port
… SDW-550-T5G 10/100/1000Base-T/TX: 5 ports
+
+
SDW-541-F1G-T4G SDW-550-T5G

11
6644-2240
1234
Power
The SDW-500 series supports redundant power connection. The positive
inputs are +DC1 and +DC2, the negative inputs for both supplies are
COM. The power is drawn from the input with the highest voltage.
TX
Ethernet TX connection (RJ-45 connector), automatic MDI/MDI-X crossover.
CAT 5 cable is recommended.
Unshielded (UTP) or shielded (STP) connector might be used.
8
7
6
5
4
3
2
1
4-pos screw terminal Description Power
1 COM 0 V
2 +DC1 9.6–57.6 VDC
3 +DC2 9.6–57.6 VDC
4 COM 0 V
Contact Direction Description/Remark
1 In/Out BI_DA+
2 In/Out BI_DA-
3 In/Out BI_DB+
4 In/Out BI_DC+
5 In/Out BI_DC-
6 In/Out BI_DB-
7 In/Out BI_DD+
8 In/Out BI_DD-
Shield In/Out Connected to PE
F1G, 1 SFP slot
The F1G interface has one SFP slot supporting Ethernet 100/1000
BaseFX/X. Each slot can hold one SFP transceiver for copper or fibre
cable. For supported transceivers see SFP transceivers user guide (art
no. 6100-0000) available at www.westermo. com.

12
6644-2240
DIP switch settings SDW-541-F1G-T4G and SDW-550-T5G
DIP-switches are accessible under the lid on top of the unit. DIP-switches are used to
configure the unit.
Warning!
Prevent damage to internal electronics from electrostatic discharges (ESD) by
discharging your body to a grounding point (e.g. use of wrist strap), before the lid
on top/front of the unit is removed.
Warning! Do not open connected equipment.
Prevent access to hazardous voltages by disconnecting the unit from AC/DC mains
supply and all other electrical connections.
!
!
NOTE
When configuration via DIP-switches, the settings of DIP-switches configure the unit only
after a reboot (power off/on).
Observe this when the DIP-switches are configured
… Speed and duplex setting only valid when auto-negotiation is disabled.
… When monitoring selected all outgoing packets from the switch is also copied to the
port 1.
… Speed and duplex switch settings are ignored for FX ports.
… If auto-negotiation and auto MDI/MDI-X disabled all TX ports support MDI-X
configuration.
… If Hub mode is selected, all incoming and outgoing packets are distributed on all other
ports.
ONLY VALID FOR SDW-541-F1G-T4G
… Speed and duplex switch settings are ignored for FX ports.
… If auto-negotiation and auto MDI/MDI-X disabled all TX ports support MDI-X
configuration.

13
6644-2240
Port 1 settings
ON
1 2 3 4 5 6 7 8 9 10
ON
1 2 3 4 5 6 7 8 9 10
ON
1 2 3 4 5 6 7 8 9 10
ON
1 2 3 4 5 6 7 8 9 10
ON
1 2 3 4 5 6 7 8 9 10
S1
S1
S1
S1
S1
Auto-negotiation enabled
10/100/1000 Mbit/s speed
selected
100 Mbit/s speed selected
10 Mbit/s speed selected
Full duplex selected
Half duplex selected
Port 2 settings
ON
1 2 3 4 5 6 7 8 9 10
ON
1 2 3 4 5 6 7 8 9 10
ON
1 2 3 4 5 6 7 8 9 10
1 2 3 4 5 6 7 8 9 10
ON
1 2 3 4 5 6 7 8 9 10
S1
S1
S1
S1
S1
ON
Auto-negotiation enabled
10/100/1000 Mbit/s speed
selected
100 Mbit/s speed selected
10 Mbit/s speed selected
Full duplex selected
Half duplex selected
Port 3 settings
ON
1 2 3 4 5 6 7 8 9 10
ON
1 2 3 4 5 6 7 8 9 10
ON
1 2 3 4 5 6 7 8 9 10
ON
1 2 3 4 5 6 7 8 9 10
ON
1 2 3 4 5 6 7 8 9 10
S1
S1
S1
S1
S1
Auto-negotiation enabled
10/100/1000 Mbit/s speed
selected
100 Mbit/s speed selected
10 Mbit/s speed selected
Full duplex selected
Half duplex selected
Port 5 settings
ON
1 2 3 4 5 6 7 8 9 10
ON
1 2 3 4 5 6 7 8 9 10
ON
1 2 3 4 5 6 7 8 9 10
ON
1 2 3 4 5 6 7 8 9 10
S2
S2
S2
S2
1000 Mbit/s speed selected
100 Mbit/s speed selected
Full duplex selected.
Note: Only valid for TX
SFP
Half duplex selected.
Note: Only valid for TX
SFP
Port settings
Port 5 settings
ON
1 2 3 4 5 6 7 8 9 10
ON
1 2 3 4 5 6 7 8 9 10
ON
1 2 3 4 5 6 7 8 9 10
1 2 3 4 5 6 7 8 9 10
ON
1 2 3 4 5 6 7 8 9 10
S2
S2
S2
S2
S2
ON
Auto-negotiation enabled
10/100/1000 Mbit/s speed
selected
100 Mbit/s speed selected
10 Mbit/s speed selected
Full duplex selected
Half duplex selected
Port 5 settings below only valid for
SDW-541-F1G-T4G
Port 5 settings below only valid for
SDW-550-T5G
S1
S2
S2
ON
1 2 3 4 5
ON
1 2 3 4 5 6 7 8 9 10
ON
1 2 3 4 5 6 7 8 9 10
ON
1 2 3 4 5 6 7 8 9 10
ON
1 2 3 4 5 6 7 8 9 10
ON
1 2 3 4 5 6 7 8 9 10
S1
S1
ON
1 2 3 4 5 6 7 8 9 10
Auto-negotiation enabled
10/100/1000 Mbit/s speed
selected
100 Mbit/s speed
selected
10 Mbit/s speed
selected
Full duplex selected
Half duplex selected
S2
S2
Port 4 settings

14
6644-2240
S1 S2
Port mirroring settings
ON
1 2 3 4 5 6 7 8 9 10
ON
1 2 3 4 5 6 7 8 9 10
S2 No monitoring
selected
S2 Monitoring selected
Hub mode
ON
1 2 3 4 5 6 7 8 9 10
ON
1 2 3 4 5 6 7 8 9 10
S2 Hub mode enabled
S2 Hub mode disabled
Factory settings
S1 S2
ON
1 2 3 4 5 6 7 8 9 10
ON
1 2 3 4 5 6 7 8 9 10
Flow control selected
ON
1 2 3 4 5 6 7 8 9 10
S2 Flow control selected
S2 No flow control
selected
ON
1 2 3 4 5 6 7 8 9 10

15
6644-2240
LED indicators
Indicators (LED)
Power (PWR)
Link (LINK) of every port
Speed (SPD) and duplex (DPX) of TX ports
LED Status Description
PWR ON Internal power, initialising OK
Slow flash Initialisation progressing
Fast flash Initialisation error
LINK/SPD OFF No Ethernet link
ON Good Ethernet link
Flash Ethernet data is transmitted or received, traffic indication
Flash 3 Hz 10 Mbit/s
Flash 6 Hz 100 Mbit/s
Flash 12 Hz 1000 Mbit/s
DPX OFF Half duplex
(TX only) ON Full duplex
SFP Transceivers
The unit supports Westermo labelled transceivers only. See Westermo's modular
transceivers datasheets 100 Mbit and 1 Gbit for supported SFP transceivers. See
Transceiver User Guide "6100-0000" for transceiver handling instructions.
www.westermo.com – A Beijer Electronics Group Company
Gigabit Transceivers
RedFox, Lynx series and ODW-700 series
The Westermo range of Small Form-factor Pluggable (SFP) transceivers covers versions suitable for Gigabit applications.
LC connectors are used as standard due their small size.
These transceivers have been ver ified to meet the Westermo environmental specification and can operate in a range
of different Westermo products in harsh industr ial applications. The transceivers are coded to allow confirmation that
certified versions h ave been installed.
Versions are available with different wave length including 1550 nm for extreme distances upto 120 km (74.5 mi)
and 1310 nm version for both single (9/125) and multimode cables (50/125 and 62.5/125). In applications where only
a single fibre core is available a Bi-Directional (BiDi) transceiver can be used.
…Wide choice to provide optimal solution
• 1000 Mbit/s versions
• Standard LC connector type
…Verified to meet Westermo environmental specifications
• Temperature range –40 to +85°C (–40 to +185°F)
• Coded to guarantee quality
…Different transcivers for many solutions
• Multi mode fibre up to 2 km (1.2 mi)
• Single mode fibre up to 120 km (74.5 mi)
• Bi-directional fibre transciversup to 120 km (74.5 mi)
• Gbit copper transceivers
EN 60825-1
Eye Safety: Class 1 laser product complies
Component Recognition
RXTX
Interfaces How far can we get with transceivers
The different transceiver options are marked with an
indicative range as a part of the transceiver descr iption.
This is the specified distance when the transceiver is used
in Gbit applications.
For the ODW series the maximum distance (km) can be
calculated with the formula:
Power budget (dB) – signal loss (dB) / fibre attenuation
(db) per km.
Signal loss = splice attenuation x number of splices + con-
nector attenuation x number of connectors + safety margin.
Splice, connector and fibre attenuation can be found on article
data sheets.
By calculating the maximum distance based on power
budget a LC2 multimode transceiver can operate
up to 5 km (3.1 mi).
Transceivers 1Gbit_1509_EN_REV. B
www.westermo.com – A Beijer Electronics Group Company
100 Mbit Transceivers
RedFox, Lynx series and ODW-700 series
The Westermo range of Small Form-factor Pluggable (SFP) transceivers covers versions suitable for 10/100 Mbit/s
applications. LC connectors are used as standard due their small size.
These transceivers have been ver ified to meet the Westermo environmental specification and can operate in a range
of different Westermo products in harsh industr ial applications. The transceivers are coded to allow confirmation that
certified versions h ave been installed.
Versions are available with different wave length including 1550 nm for extreme distances upto 120 km (74.5 mi)
and 1310 nm version for both single (9/125) and multimode cables (50/125 and 62.5/125). In applications where only
a single fibre core is available a Bi-Directional (BiDi) transceiver can be used.
…Wide choice to provide optimal solution
• 100 Mbit/s versions
• Standard LC connector type
…Verified to meet Westermo environmental specifications
• Temperature range –40 to +85°C (–40 to +185°F)
• Coded to guarantee quality
…Different transcivers for many solutions
• Multi mode fibre up to 2 km (1.2 mi)
• Single mode fibre up to 120 km (74.5 mi)
• Bi-directional fibre transciversup to 120 km (74.5 mi)
• 100 Mbit copper transceivers
EN 60825-1
Eye Safety: Class 1 laser product complies
Component Recognition
RXTX
Interfaces How far can we get with transceivers
The different transceiver options are marked with an
indicative range as a part of the transceiver descr iption.
This is the specified distance when the transceiver is used
in 100 Mbit applications.
For the ODW series the maximum distance (km) can be
calculated with the formula:
Power budget (dB) – signal loss (dB) / fibre attenuation
(db) per km.
Signal loss = splice attenuation x number of splices + con-
nector attenuation x number of connectors + safety margin.
Splice, connector and fibre attenuation can be found on article
data sheets.
By calculating the maximum distance based on power
budget a LC2 multimode transceiver can operate
up to 5 km (3.1 mi).
Transceivers 100Mbit_1510_EN_REV. B
ESD Protection
www.westermo.com
©
WestermoTeleindustri AB
User Guide
6100-0000
SFP
Transceivers

16
6644-2240
Mounting
This unit should be mounted on 35 mm DIN-rail, which is horizontally mounted on a
wall or cabinet backplate. Snap on mounting, see figure.
Removal
Cooling
This unit uses convection cooling.
To avoid obstructing the airflow
around the unit, use the following
spacing rules. Minimum spacing 25 mm
(1.0 inch) above / below and 10 mm
(0.4 inches) left / right the unit.
Spacing is recommended for the use
of unit in full operating temperature
range and service life.
Press down the black support at the back of the unit, see figure.
CLICK!
CLICK!
10 mm *
(0.4 inches)
25 mm
25 mm
* Spacing (left/right) recommended for
full operating temperature range

17
6644-2240

18
6644-2240

19
6644-2240

REV. F 6644-2240 2017-05 Westermo Teleindustri AB, Sweden
For complete contact information, please visit our website at www.westermo.com/contact or scan the QR code
China
[e-mail]
www.cn.westermo.com
France
[e-mail]
www.westermo.fr
Germany
[e-mail]
www.westermo.de
North America
[e-mail]
www.westermo.us
Singapore
[e-mail]
www.westermo.com
Sweden
[e-mail]
www.westermo.se
United Kingdom
[e-mail]
www.westermo.co.uk
Other Offices
Sales Units
Westermo Data Communications
Westermo • SE-640 40 Stora Sundby, Sweden
Tel [phone] Fax [phone]
E-mail: [e-mail]
www.westermo.com