Westermo DDW-02-B1 User manual

www.westermo.com
DDW-02-B1
EN 50155 Ethernet Broadband Bridge
DC2
ON
DC1 X1 X1
LINK STATUS
ACTIVITY
LINK MASTER
M12 Torque
0,6±0,1Nm / 0,45±0,1 lbft
10/100 BASE-TX
LINK
POWER

26641-2280
Legal information
The contents of this document are provided “as is”. Except as required by applicable
law, no warranties of any kind, either express or implied, including, but not limited to,
the implied warranties of merchantability and fitness for a particular purpose, are made
in relation to the accuracy and reliability or contents of this document. Westermo
reserves the right to revise this document or withdraw it at any time without prior
notice.
Under no circumstances shall Westermo be responsible for any loss of data or income
or any special, incidental, and consequential or indirect damages howsoever caused.
More information about Westermo can be found at the following Internet address:
http://www.westermo.com

3
6641-2280
Safety
Before installation:
Read this manual completely and gather all information on the unit. Make sure
that you understand it fully. Check that your application does not exceed the safe
operating specifications for this unit.
This unit should only be installed by qualified personnel.
This unit should be built-in to an apparatus cabinet, or similar, where access is
restricted to service personnel only. The power supply wiring must be sufficiently
fused, and if necessary it must be possible to disconnect manually from all power
supply. Ensure compliance to national installation regulations. This unit relies on
convection heating. Make sure that it is installed so that the ambient temperature
is within the specified temperature range, e.g. by avoiding obstruction of the
airflow around the unit. Also check chapter EN 45545-2 mounting notes.
Before mounting, using or removing this unit:
Prevent access to hazardous voltage by disconnecting the unit from all power supply.
WARNING
Do not open connected unit. Hazardous voltage may occur within this unit when
connected to power supply.
Before powering-up, a protective earthing conductor must be connected to the
protective earthing terminal and have a cross-sectional area of at least 1.5 mm².
Note that this unit can be connected to two different power sources.
To reduce the risk of fire, use only No. 26 AWG or larger telecommunication line
cord.
!
!

46641-2280
Care recommendations
Follow the care recommendations below to maintain full operation of unit and to fulfill
the warranty obligations:
…Do not attempt to dissassemble the unit. There are not any user serviceable
parts inside.
…Do not drop, knock or shake the unit. Rough handling above the specification
may cause damage to internal circuit boards.
…Do not use harsh chemicals, cleaning solvents or strong detergents to clean
the unit.
…Do not expose the unit to any kind of liquid (water, beverages, paint etc),
unless all connectors are connected or fitted with protective caps (delivered
with the unit), tightened to the specified torque. Connected cables must have
the appropriate ingress protection code.
…Do not use or store the unit in dusty or dirty areas, unless all connectors and
the ventilation membrane are sufficiently protected.
…Do not cover or bring mechanical force to the ventilation membrane on the
back of the unit.
If the unit is not working properly, contact the place of purchase, nearest Westermo
distributor office or Westermo Tech support.
Maintenance
No maintenance is required, as long as the unit is used as intended within the specified
conditions.
Product disposal
This symbol means that the product shall not be treated
as unsorted municipal waste when disposing of it. It needs
to be handed over to an applicable collection point for
recycling electrical and electronic equipment.
By ensuring this product is disposed of correctly, you will
help to reduce hazardous substances and prevent potential
negative consequences to both environment and human
health, which could be caused by inappropriate disposal.

5
6641-2280
Agency approvals and standards compliance
Type Approval / Compliance
EMC EN 61000-6-1, Immunity residential environments
EN 61000-6-2, Immunity industrial environments
EN 61000-6-3, Emission residential environments
EN 61000-6-4, Emission industrial environments
EN 50121-3-2, Railway applications – Rolling stock – apparatus
EN 50121-4/IEC 62236-4, Railway signaling and telecommunications apparatus
IEEE 16 - IEEE Standard for Electrical and Electronic Apparatus on Rail Vehicles
Tested and verified for FCC part 15, class A
Safety EN/IEC 60950-1 IT equipment
Environmental EN 50124-1 – Railway applications – Insulation coordination
EN 50155 – Railway applications – Electronic equipment used on rolling stock
EN 61373 – Railway applications – Rolling stock equipment. Shock and vibration tests
IEC 60068-2-27 – Shock
IEC 60068-2-64 – Vibration, broadband random and guidance
IEEE 1478 –Environmental conditions for transit rail car electronic equipment
EN 45545-2 Fire protection
FCC Part 15.105
Notice:
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
… Reorient or relocate the receiving antenna
… Increase the separation between the equipment and receiver
… Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected
… Consult the dealer or an experienced radio/TV technician for help.
Simplified EU declaration of conformity
Hereby, Westermo declares that the equipment is in compliance with EU directives. The
full EU declaration of conformity and other detailed information are available at the
respective product page at www.westermo.com. .

66641-2280
Type tests and environmental conditions
Environmental phenomena Basic standard Description Test levels
ESD EN 61000-4-2 Enclosure Contact: ±6 kV
Air: ±8 kV
Fast transients EN 61000-4-4 Power port ±2 kV
Signal ports ±2 kV
Earth port ±1 kV
Surge EN 61000-4-5 Power port L-E: ±2 kV, 12Ω, 9 μF, 1.2/50 μs
L-L: ±1 kV, 2Ω, 18 μF, 1.2/50 μs
L-E: ±2 kV, 42Ω, 0.5 μF, 1.2/50 μs
L-L: ±2 kV, 42Ω, 0.5 μF, 1.2/50 μs
Ethernet ports L-E: ±2 kV, 2 Ω
Power frequency magnetic field EN 61000-4-8 Enclosure 300 A/m; 0, 16.7, 50, 60 Hz
Pulsed magnetic field EN 61000-4-9 Enclosure 300 A/m
Radiated RF immunity EN 61000-4-3 Enclosure 20 V/m @ (80 MHz – 2.7 GHz)
1 kHz sine, 80% AM
10 V/m @ (2.7 – 6 GHz)
1 kHz sine, 80% AM
Conducted RF immunity EN 61000-4-6 Power port 10 V, 80% AM, 1 kHz; (0.15 – 80) MHz
Ethernet ports 10 V, 80% AM, 1 kHz; (0.15 – 80) MHz
Earth port 10 V, 80% AM, 1 kHz; (0.15 – 80) MHz
Radiated RF emission CISPR 16-2-3 Enclosure Class B (30 – 2000 MHz)
ANSI C63,4
(FCC Part 15)
Class B (30 – 2000 MHz)
Conducted RF emission CISPR 16-2-1 Power port Class B
Ethernet ports Class B
Dielectric strength EN 60950-1 Power port
to all other ports
1.5 kV ACrms, 50 Hz, 1 min
Fast Ethernet ports
to all other ports
1.5 kVACrms, 50 Hz, 1 min
Link to all other
ports
1.5 kVrms, 50 Hz, 1 min
Environmental
Temperatures EN 60068-2-1
EN 60068-2-2
Operating –40 to +70°C (–40 to +158°F)
Storage and transport –50 to +85°C (–58 to +185°F)
Humidity EN 60068-2-30 Operating 5 to 95% relative humidity
Storage and transport 5 to 95% relative humidity
Altitude Operating 2 000 m / 70 kPa
Service life Operating 15 years
MTBF 1,568,000 hours MIL-C217F2, GB, 25°C (+77°F)
Vibration IEC 60068-2-64
(random)
Operating 2 m/s² (RMS) 5 – 150 Hz
Shock IEC 60068-2-27 Operating 10 g, 30 ms, 20 g, 11 ms
Enclosure EN 60950-1 Zinc Fire enclosure
Dimension W x H x D
With connectors
See "Dimensions" chapter for details
Weight 1.4 kg
Degree of protection EN 60529 Enclosure IP67
Cooling Convection

7
6641-2280
Description
Made easy for extending Ethernet
The Wolverine series consists of Ethernet extenders and bridges for propagating
Ethernet traffic over existing cabling. The Ethernet link can be allowed to be extended
over longer distances than possible with pure copper Ethernet and at data rates of up to
70 Mbit/s.
The DDW-002-B1 makes it possible to reuse many types of pre-existing copper cables
since it is based on power line communication (IEEE 1901). A network with the DDW-
002-B1 devices is capable of bridging high bandwidth Ethernet traffic over 2-wire cables,
even when there are corroded connector.s The powerline communication standard is
designed to establish a reliable communication link over both twisted pair and parallell
cabling.
This can lead to considerable financial savings when refurbishing a train with Ethernet
communication, as existing train couplers can be reused without the need for a costly
rebuild or even replacement. By simply installing a DDW-002-B1 on each side of the
coupler, a bridge connecting the Ethernet networks on each side is created. The fact that
no configuration is needed further contributes to the ease of use.
Designed for harsh industrial environments
The DDW-002-B1 has been thoroughly tested by certified labs to ensure its compliance
with the standard for electronic equipment used on rolling stock, the EN 50155. For
several characteristics, Westermo exceeds the requirements mandated by the standard.
Furthermore, the design is based on Westermo’s long experience within the rolling stock
market, which brings benefits such as vibration safe integrated connector threading, IP67
ingress protection with GORE-TEX® membrane to prevent condensation water build-up
and ultimately a high MTBF and long service life under the harshest conditions.
Meeting the requirements for rolling stock, makes the DDW-002-B1 also very well suited
for deployment in other applications with severe operating conditions and extreme
environments.

86641-2280
Interface specifications
DC, Power port
Rated voltage 24 to 110 VDC
Operating voltage 16.8 to 143 VDC (14.4 VDC for 100 ms, 154 VDC for 1 s)
Rated current 350 mA @ 24 VDC and 90 mA @ 110 VDC
Rated frequency DC
Inrush current, I²t 1 mA²s @ 24 V and 6 mA²s @ 110 V
Startup current* 535 mA @ 24 V
145 mA @ 110 V
Polarity Reverse polarity protected
Redundant power input Yes
Isolation to 1500 VAC rms to all other
Connection 4 pin male M12 A-coded connector, use Westermo cable
3146-1106 for 1.5 m
3146-1107 for 5 m
Connector size M12, recommended cable area 0.5 mm² (minimum 0.25 mm²),
cable dimensions depend on choice of M12 connector
* External supply current capability for proper start-up
X1 Ethernet ports
Electrical specification IEEE std 802.3. 2005 Edition
Data rate Auto-negotiation (10 Mbit/s or 100 Mbit/s)
Duplex Auto-negotiation (full or half)
Circuit type X1: TNV-1
Transmission range Up to 150 m with CAT5e cable or better
Isolation to 1500 VAC rms to all other ports
Connection 4-pin M12 D-code, auto MDI/MDI-X, use e g Westermo cable
3146-1100 M12-M12 – 1 m
3146-1101 M12-M12 – 5 m
3146-1103 RJ45-M12 – 1 m
3146-1104 RJ45-M12 – 5 m
Shielded cable Not required, but recommended in severe electromagnetic
environments
Conductive housing Yes
Number of ports 1
X2 Powerline interface
Data rate Up to 70 Mbit/s (depending on cable characteristics and
temperature
Connection 4-pin M12 B-code
Transmission range Up to 300 m (depending on cable characteristics and
temperature)
Electrical specification Supports communication over wires powered from 0 to 143
VDC.

9
6641-2280
X1 LINK STATUS
ACTIVITY
LINK MASTER
0,6±0,1Nm / 0,45±0,1 lbft
10/100 BASE/TX LINK
DC1
DC2
ON
POWER
X2
M12 Torque
Location of interface ports and LEDs
Ethernet connection TX
Power connection
LED indicators
Earth
connection
Powerline connection

10 6641-2280
Connector pinout
Power connection
Pin number Signal
2 1
3 4
No 1 +DC1
No 2 +DC2
No 3 -COM
No 4 -COM
Ethernet connection
Pin number Signal
No 1 TD+
No 2 RD+
No 3 TD–
No 4 RD–
Housing Shield
Auto MDI/MDI-X is used. The table shows signals in
MDI mode.
Powerline connection
Pin number Signal 1 4
2 3
No 1 PLC1
No 2 NC
No 3 PLC2
No 4 NC
PLC1 and PLC2 are polarity free.