Westermo MRI-128-F4G Series User manual

1
MRI-128-F4G
Series
User’sManual
Version1.0









IndustrialManaged
EthernetSwitch


2































CopyrightNotice

Copyright©2010WestermoTeleindustriAB
Allrightsreserved.
Reproductioninanyformorbyanymeanswithoutpermissionisprohibited.


3
FederalCommunicationsCommission(FCC)Statement

ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforaClassA
digitaldevice,pursuanttoPart15oftheFCCRules.Theselimitsaredesignedto
providereasonableprotectionagainstharmfulinterferencewhentheequipmentis
operatedinacommercialenvironment.Thisequipmentgenerates,uses,andcan
radiateradiofrequencyenergyand,ifnotinstalledandusedinaccordancewiththe
instructionmanual,maycauseharmfulinterferencetoradiocommunications.
Operationofthisequipmentinaresidentialareaislikelytocauseharmful
interferenceinwhichcasetheuserwillberequiredtocorrecttheinterferenceathis
expense.
Theuseriscautionedthatchangesandmodificationsmadetotheequipment
withoutapprovalofthemanufacturercouldvoidtheuser’sauthoritytooperatethis
equipment.

Index
1Introduction..........................................................................................................2
1.1Overview....................................................................................................2
1.2MajorFeatures...........................................................................................3
1.3PackageList................................................................................................4
2HardwareInstallation............................................................................................5
2.1HardwareIntroduction..............................................................................5
2.2WiringPowerInputs..................................................................................6
2.3WiringEarthGround..................................................................................7
2.4WiringFastEthernetPorts.........................................................................7
2.5WiringFiberPorts......................................................................................8
2.6WiringGigabitComboPorts......................................................................9
2.7WiringRS‐232ConsoleCable.....................................................................9
2.8RackMountingInstallation........................................................................9
2.9SafetyWarning.........................................................................................12
3PreparationforManagement.............................................................................13
3.1PreparationforSerialConsole.................................................................13
3.2PreparationforWebInterface.................................................................14
3.3PreparationforTelnetConsole................................................................16
4FeatureConfiguration.........................................................................................19
4.1CommandLineInterfaceIntroduction.....................................................19
4.2BasicSetting.............................................................................................25
4.3PortConfiguration....................................................................................46
4.4NetworkRedundancy...............................................................................59
4.5VLAN.........................................................................................................71
4.6TrafficPrioritization..................................................................................82
4.7MulticastFiltering....................................................................................89
4.8SNMP........................................................................................................96
4.9Security..................................................................................................100
4.10Warning..................................................................................................117
4.11MonitorandDiag...................................................................................123
4.12DeviceFrontPanel.................................................................................133
4.13SavetoFlash...........................................................................................134
4.14Logout....................................................................................................135

1
5Appendix...........................................................................................................136
5.1PinAssignmentoftheRS‐232ConsoleCable........................................136
5.2PrivateMIB.............................................................................................137
5.3RevisionHistory......................................................................................138

2
1Introduction

WelcometoMRI‐128‐F4GRackmountManagedEthernetSwitchUserManual.
Followingtopicsarecoveredinthischapter:
1.1 Overview
1.2 MajorFeatures
1.3 PackageChecklist

1.1 Overview

TheMRI‐128‐F4GSeries,the19‐inch24+4GManagedEthernetRingSwitch,is
equippedwith2410/100Base‐TXportsplus4GigabitRJ45/MINIGBICcombo
ports.Theswitchisspeciallydesignedforcontrolroomswherehigh‐port
densityandperformancearerequired.TheGigabitComboportallows
10/100/1000triplespeedofcopperports,andtheSFPportsacceptalltypesof
GigabitSFPtransceivers,includingGigabitSX,LX,LHX,ZXandXDforseveral
connectionsanddistances.

ModelNameDescription
MRI‐128‐F4G 
RackmountManagedEthernetSwitchwith2410/100
Base‐TX+4GigabitComboPorts,90‐264VACinput
MRI‐128‐F4G/DC


RackmountManagedEthernetSwitchwith2410/100
Base‐TX+4GigabitComboPorts,24V(12‐48V)DCinput

Thedeviceismountedwithinthe19inchrack,alongwithother19inchpublic
serversorothernetworkdevices.Whenotherindustrialswitchesare
aggregatedtotheswitch,the24+4Gdesignallowsconnectingupto12100M
ringsplus2Gigabitringsandeachringhasitsownringredundancyprotection.
Theswitchisdesignedasafan‐lessrackmountswitchwithlowpower
consumptionandwideoperatingtemperature.TheMRI‐128‐F4G/DCallows
24V(12‐48V)DCinput.TheswitchsupportsJumboframefeaturingupto9,216
bytespacketsizeforlargesizefiletransmissionwhichisthetrendforfuture
industrialapplicationrequests.

3
TheswitchsupportsRSTP,MultipleSuperRingtechnology,VLAN,IGMP
Snooping,LACPfornetworkcontrol,SNMPandLLDPfornetworkmanagement.
SecuredaccessisprotectedbyPortSecurity,802.1xandflexibleLayer2/4 
AccessControlList.

1.2 MajorFeatures

•24‐port10/100Base‐TXand4‐portGigabitRJ‐45/SFPcomboports
(10/100/1000Base‐TX,1000Base‐X)
•Non‐BlockingSwitchingPerformance,nocollisionordelaywhenwire‐speed
transmission
•SupportsJumboFrameupto9,216byte
•RSTPandMultipleSuperRing(RapidSuperRing,RapidDualHoming,
MultiRing,TrunkRing)
•Maximum12x100MRingsplus2GigabitRingsaggregationcapability
•VLAN,LACP,GVRP,QoS,IGMPSnooping,RateControl,OnlineMultiPort
MirroringandWeDashboard
•LinkLayerDiscoveryProtocol(LLDP),SNMPV1/V2c/V3,RMON
•AdvancedSecuritysupportsIP/PortSecurity,802.1xandAccessControlList
•EventNotificationbyE‐mail,SNMPTrap,SyslogandRelayOutput
•90‐264VACorDual12‐48VDCpowerinput.


4
1.3 PackageList

MRI‐128‐F4G24+4GRackmountManagedEthernetRingSwitch
Includes:
•Theswitch(noSFPtransceivers)
•RackMountKit
•ConsoleCable
•PowerCord
•DocumentCD

MRI‐128‐F4G/DC24+4GRackmountManagedEthernetRingSwitchwith
12‐48VDCinput
Includes:
•Theswitch(noSFPtransceivers)
•RackMountKit
•ConsoleCable
•DocumentCD
Ifanyoftheaboveitemsaremissingordamaged,pleasecontactyourlocal
salesrepresentative.


5
2HardwareInstallation

Thischapterincludeshardwareintroduction,installationandconfiguration
information.
Followingtopicsarecoveredinthischapter:

2.1 HardwareIntroduction
2.2 WiringPowerInputs
2.3 WiringEarthGround
2.4 WiringEthernetPorts
2.5 WiringFiberPorts
2.6 WiringGigabitComboPorts
2.7 WiringRS‐232consolecable
2.8 RackMountingInstallation
2.9 SafetyWarning

2.1 HardwareIntroduction
LED
System:Power(Green),RingMaster(Green)
10/100RJ‐45:
Link/Activity:Green=100M,Yellow=10M;
Duplex:On=Full,Off=Half
GigabitCopper/SFP:
Link/Activity:Green=1000M,Yellow=10Mor100M;
Duplex:On=Full,Off=Half)
GigabitSFP:Link/Activity(Green/GreenBlinking)

Dimension
44mm(H)x438mm(W)x170mm(D)

6


PanelLayout
ThefrontpanelincludesRS‐232ConsolePort,System&PortLEDs,Fast
EthernetPortInterfacesandGigabitComboPortInterfaces.
TheconsoleportchoosesRS‐232DB‐9types.Thepinarrangementis“Pin2:TxD,
Pin3:RxD,Pin5:GND”.Theconsolecableisshippedwiththeswitch.
IntheRearpanel,thereare2typespowerinputconnectorappliedtothe
switchandtheswitch‐DC.
TheACvariancechoosesstandardACplugaspowerinputsocket.TheDC
variancechooses4‐pinterminalblockaspowerinputsocket.FollowtheV+,V‐
indicationintherearpaneltoscrewthepowersource.

2.2 WiringPowerInputs

TheMRI‐128‐F4Gseriesprovidestwovarianceswithdifferentpowerinputs.

ACPowerInput
ConnecttheattachedpowercordtotheACpowerinputconnector,the
availableACpowerinputisrangefrom90‐264VAC.

DCPowerInput
Thesuggestedpowerinputis24VDC,theavailablerangeisfrom12‐48VDC.
FollowbelowstepstowiretheswitchredundantDCpowerinputs.
MRI‐128‐F4G/DC
MRI‐128‐F4G

7

1. InsertpositiveandnegativewiresintoV+
andV‐ contactsrespectivelyofthe
terminalblockconnector
2. Tightenthewire‐clampscrewstoprevent
DCwiresfrombeingloosened.
3. Power1andPower2supportpower
redundancy.
4. Positiveandnegativepowersystem
inputsarebothaccepted,butPower1
andPower2mustapplythesamemode.
Note1:Itisagoodpracticetoturnoffinputand
loadpower,andtounplugpowerterminalblockbeforemakingwire
connections.Otherwise,yourscrewdriverbladecaninadvertentlyshortyour
terminalconnectionstothegroundedenclosure.
Note2:TherangeofthesuitableDCelectricwireisfrom12to24AWG.
Note3:PleasefollowtheV+andV‐ indicator.Incorrectwiringwouldnot
damagetheswitch,onlypreventtheswitchtopowerupNote4:Pleasefollow
theV+andV‐ indicator.Incorrectwiringwouldnotdamagetheswitch,only
preventtheswitchtopowerup

2.3 WiringEarthGround

Toensurethesystemwillnotbedamagedbynoiseoranyelectricalshock,we
suggestyoutomakeexactconnectionwithEarthGround.
ForACinput,the3pinincludeV+,V‐andGND.TheGNDpinmustbeconnected
totheearthground.
ForDCinput,loosentheearthgroundscrewusingascrewdriver;thentighten
thescrewafterearthgroundwireisconnected.

2.4 WiringFastEthernetPorts

Theswitchincludes24RJ‐45FastEthernetports.TheFastEthernetports
support10Base‐Tand100Base‐TX,fullorhalfduplexmodes.AlltheFast
Ethernetportswillauto‐detectthesignalfromconnecteddevicestonegotiate
thelinkspeedandduplexmode.AutoMDI/MDIXallowsuserstoconnect
anotherswitch,huborworkstationwithoutchangingstraightthroughor
crossovercables.

8
Notethatcrossovercablessimplycross‐connectthetransmitlinesateachend
tothereceivedlinesattheoppositeend.


Straight‐throughCablingSchematicCross‐overCablingSchematic

NotethatEthernetcablesusepins1,2,3,and6ofan8‐pinRJ‐45connector.The
signalsofthesepinsareconvertedbytheautomaticMDI‐Xfunction,asshownin
thetablebelow:

PinMDI‐XSignalsMDISignals
1RD+TD+
2RD‐ TD‐
3TD+RD+
6TD‐ RD‐

ConnectonesideofanEthernetcableintoanyswitchportandconnectthe
othersidetoyourattacheddevice.TheLNKLEDwilllightupwhenthecableis
correctlyconnected.RefertotheLEDIndicatorssectionfordescriptionsofeach
LEDindicator.Alwaysmakesurethatthecablesbetweentheswitchesand
attacheddevices(e.g.switch,hub,orworkstation)arelessthan100meters(328
feet).
Thewiringcabletypesareasbelow.
10Base‐T:2‐pairUTP/STPCat.3,4,5cable,EIA/TIA‐568100‐ohm(100m)
100Base‐TX:2‐pairUTP/STPCat.5cable,EIA/TIA‐568100‐ohm(100m)
1000Base‐TX:4‐pairUTP/STPCat.5ecable,EIA/TIA‐568100‐ohm(100m)

2.5 WiringFiberPorts

SmallForm‐factorPluggable(SFP)
TheSFPportsfulfilltheSFPstandard.Toensurethesystemreliability,itis
recommendedtousetheapprovedGigabitSFPTransceiver.Thewebuser
interfacewillshowUnknownvendortypewhenchoosingtheSFPwhichisnot
approved.

9
ThewaytoconnecttheSFPtransceiveristoPluginSFPfibertransceiverfirst.
Cross‐connectthetransmitchannelateachendtothereceivechannelatthe
oppositeendasillustratedinthefigurebelow.



Note:ThisisaClass1Laser/LEDproduct.Don’tstareattheLaser/LEDBeam.

2.6 WiringGigabitComboPorts

Theswitchincludes4RJ‐45GigabitEthernetportswhichsupports10Base‐T,
100Base‐TXand1000Base‐TX.Theswitchisalsoequippedwith4GigabitSFP
portscombowhichsupports1000Base‐SX/LXandisaccordingthestandardMINI
GBICSFPtransceiver.

2.7 WiringRS‐232ConsoleCable

WestermoattachesoneRS‐232DB‐9toDB‐9cableinthebox.ConnecttheDB‐9
connectortotheCOMportofyourPC,openTerminaltoolandsetupserial
settingsto9600,N,8,1.(BaudRate:9600/Parity:None/DataBit:8/StopBit:1)
ThenyoucanaccesstheCLIinterfaceusingtheconsolecable.
Note:Ifyoulostthecable,pleasecontactyourlocalsalesofficeorfollowthepin
assignmenttobuy/makeanewone.Thepinassignmentspecislistedinthe
appendix.

2.8 RackMountingInstallation

TheRackMountKitisattachedinsidethepackagebox.

10
Attachthebracketstothedevicebyusingthescrewsprovidedinthe
RackMountkit.


Mountthedeviceinthe19’rackbyusingfourrack‐mountingscrews.

Wheninstallingmultipleswitches,mountthemintherackonebelowtheother.
It’srequestedtoreserve0.5U‐1Ufreespaceformultipleswitchesinstallingin
hightemperatureenvironment.Thisisimportanttodispersetheheatgenerated
bytheswitch.


11
Noticewheninstalling:
zTemperature:Checkifthetemperatureconformstothespecifiedoperating
temperaturerange.
zMechanicalLoading:Donoplaceanyequipmentontopoftheswitch.In
highvibrationenvironment,additionalrackmountingprotectionisnecessary,
liketheflatboardunder/abovetheswitch.
zGrounding:Rack‐mountedequipmentshouldbeproperlygrounded.


12

2.9 SafetyWarning

2.2.1TheEquipmentintendedforinstallationinaRestrictedAccessLocation.


2.2.2Thewarningtestisprovidedinusermanual.Belowistheinformation:
”Fortilslutningafdeovrigeledere,semedfolgendeinstallationsvejledning”.
“Laiteonliitettavasuojamaadoitus‐koskettimillavarustettuunpistorasiaan”
„Apparatetmatilkoplesjordetstikkontakt“
”Apparatenskallanslutastilljordatuttag”


13
3PreparationforManagement

Theswitchprovidesbothin‐bandandout‐bandconfigurationmethods.You
canconfiguretheswitchviaRS232consolecableifyoudon’tattachyouradmin
PCtoyournetwork,orifyoulosenetworkconnectiontotheswitch.Thisis
so‐calledout‐bandmanagement.Itwouldn’tbeaffectedbynetwork
connectivity.
Thein‐bandmanagementmeansyoucanremotelymanagetheswitchviathe
network.YoucanchooseTelnetorWeb‐basedmanagement.Youjustneedto
knowthedevice’sIPaddressandyoucanremotelyconnecttoitsembedded
HTTPwebpagesorTelnetconsole.
Followingtopicsarecoveredinthischapter:

3.1 PreparationforSerialConsole
3.2 PreparationforWebInterface
3.3 PreparationforTelnetconsole

3.1 PreparationforSerialConsole

Inthepackage,thereisoneRS‐232DB‐9toDB‐9consolecable.Pleaseattach
RS‐232DB‐9connectortoyourPCCOMport,connecttheotherendtothe
Consoleportoftheswitch.Ifyoulose/lostthecable,pleasefollowtheconsole
cablePINassignmenttofindanewone,orcontactyourclosestWestermo
salesoffice.(Refertotheappendix).
1. GotoStart‐>Program‐>Accessories‐>Communication‐>HyperTerminal
2. Giveanametothenewconsoleconnection.
3. ChoosetheCOMname
4. Selectcorrectserialsettings.Theserialsettingsoftheswitchareasbelow:
BaudRate:9600/Parity:None/DataBit:8/StopBit:1
5. Afterconnected,youcanseeSwitchloginrequest.
6. Logintotheswitch.Thedefaultusernameis“admin”,password,
“westermo”.

Switch login: admin
Password:
The switch (version 1.1-20101014-11:04:13).
Switch>

14

3.2 PreparationforWebInterface

TheswitchprovidesHTTPWebInterfaceandSecuredHTTPSWebInterfacefor
webmanagement.

3.2.1 WebInterface

WebmanagementpageisdevelopedbyJAVA.Itallowsyoutouseastandard
web‐browsersuchasMicrosoftInternetExplorer,orMozillaFirefox,to
configureand/orlogfromtheswitchfromanywhereonthenetwork.
Beforeyouattempttousetheembeddedwebinterfacetomanageswitch
operation,verifythattheswitchisproperlyinstalledonyournetworkandthat
thePConthisnetworkcanaccesstheswitchviathewebbrowser.
1. Verifythatyournetworkinterfacecard(NIC)isoperational,andthatyour
operatingsystemsupportsTCP/IPprotocol.
2. WireDCpowertotheswitchandconnectyourswitchtoyourcomputer.
3. MakesurethattheswitchdefaultIPaddressis192.168.2.200.
4. ChangeyourcomputerIPaddressto192.168.2.2orotherIPaddresswhich
islocatedinthe192.168.2.x(NetworkMask:255.255.255.0)subnet.
5. SwitchtoDOScommandmodeandping192.168.2.200toverifyanormal
responsetime.
LaunchthewebbrowserandLogin.
6. Launchthewebbrowser(InternetExplorerorMozillaFirefox)onthePC.
7. Typehttp://192.168.2.200(ortheIPaddressoftheswitch).Andthenpress
Enter.
8. Theloginscreenwillappearnext.
9. Typeintheusernameandthepassword.Defaultusernameisadminand
passwordwestermo.

15

ClickonEnterorOK.Thewelcomepageoftheweb‐basedmanagement
interfacewillthenappear.


Onceyouentertheweb‐basedmanagementinterface,youcanfreelychange
theIPaddresstofityournetworkenvironment.

Note1:InternetExplorer5.0orlaterversionsdonotallowJavaappletsto
opensocketsbydefault.Usershavetodirectlymodifythebrowsersettingsto
selectivelyenableJavaappletstousenetworkports.
Note2:TheWebUserInterfaceconnectionsessionoftheswitchwillbelogged
outautomaticallyifyoudon’tgiveanyinputafter30seconds.Afterloggedout,
youshouldre‐loginandtypeinthecorrectusernameandpasswordagain.


16
3.2.2 SecuredWebInterface
WestermowebmanagementpagealsoprovidessecuredmanagementHTTPS
login.Alltheconfigurationcommandswillbesecured.
LaunchthewebbrowserandLogin.
1. Launchthewebbrowser(InternetExplorerorMozillaFirefox)onthePC.
2. Typehttps://192.168.2.200(ortheIPaddressoftheswitch).Andthen
pressEnter.
3. ThepopupscreenwillappearandrequestyoutotrustthesecuredHTTPS
connection.PressYestotrustit.
4. Theloginscreenwillappearnext.

5. Keyintheusernameandthepassword.Thedefaultusernameisadmin
andpasswordiswestermo.
6. PressEnterorclickonOK.Thewelcomepageoftheweb‐based
managementinterfacewillthenappear.
7. Onceyouentertheweb‐basedmanagementinterface,allthecommands
youseearethesameaswhatyouseebyHTTPlogin.

3.3 PreparationforTelnetConsole
3.3.1 Telnet
TheswitchsupportsTelnetconsole.YoucanconnecttotheswitchbyTelnet
andthecommandlinesarethesameaswhatyouseebyRS232consoleport.
BelowarethestepstoopenTel n etconnectiontotheswitch.

1. GotoStart‐>Run‐>cmd.AndthenpressEnter
2. Typethetelnet192.168.2.200(ortheIPaddressoftheswitch).Andthen
pressEnter