Westermo T200 series User manual

V3.8
OnTime Industrial Ethernet
U/R/T200 series Installation Guide
- 1 -
U/R/T200 series Installation Guide
..............................................................................................................................................

V3.8
OnTime Industrial Ethernet
U/R/T200 series Installation Guide
- 2 -

V3.8
OnTime Industrial Ethernet
U/R/T200 series Installation Guide
- 3 -
1INTRODUCTION..................................................................................................................... - 5 -
1.1 T200......................................................................................................................................- 5-
1.2 R200 .....................................................................................................................................- 5-
1.3 U200.....................................................................................................................................- 5-
2QUICK INSTALL GUIDE.......................................................................................................- 6 -
2.1.1 Release Notes – Software versions .............................................................................. - 6 -
2.1.2 Mounting, power and port connections....................................................................... - 6 -
2.1.3 Redundant ring – FRNT0 configuration...................................................................... - 6 -
3SWITCH INSTALLATION AND CONFIGURATION........................................................- 9 -
3.1 MOUNTING............................................................................................................................- 9-
3.1.1 DIN rail mounting........................................................................................................ - 9 -
3.1.2 19” dual units mounting............................................................................................ - 10 -
3.1.3 19” single unit mounting........................................................................................... - 11 -
3.1.4 Wall mounting............................................................................................................ - 12 -
3.1.5 Power connection...................................................................................................... - 13 -
3.1.6 Copper drop link connection ..................................................................................... - 13 -
3.1.7 Fiber drop link connection ........................................................................................ - 13 -
3.2 POWER SUPPLY CONNECTOR...............................................................................................- 13 -
3.2.1 Redundant power inputs............................................................................................ - 13 -
3.2.2 Fault Contact............................................................................................................. - 14 -
3.3 FRONT PANEL LED’S AND PUSH BUTTONS..........................................................................- 14 -
3.3.1 Manual Configuration............................................................................................... - 14 -
3.3.2 Normal Indication Mode............................................................................................ - 15 -
3.3.3 Select Port Mode ....................................................................................................... - 15 -
3.3.4 Speed Button.............................................................................................................. - 15 -
3.3.5 Duplex Button............................................................................................................ - 15 -
3.3.6 Auto-negotiation........................................................................................................ - 15 -
3.3.7 Save Button................................................................................................................ - 15 -
3.3.8 LED Fault indication................................................................................................. - 16 -
3.4 FIBER OPTIC CARE ...............................................................................................................- 17 -
4IP CONFIGURATION SOFTWARE.................................................................................... - 18 -
4.1 FRNT VERSION 0–SINGLE RING .........................................................................................- 23 -
4.2 FRNT VERSION 1–MULTIPLE RINGS...................................................................................- 24 -
4.3 RSTP/STP...........................................................................................................................- 25 -
4.4 SNMP.................................................................................................................................- 25 -
4.5 DHCP .................................................................................................................................- 26 -
4.6 STATIC IP ADDRESS.............................................................................................................- 26 -
4.7 IP GATEWAY ADDRESS ........................................................................................................- 27 -
4.8 PORT LINK ALARMS............................................................................................................- 27 -
4.9 ENABLING PUSH BUTTONS ..................................................................................................- 27 -
4.10 PORT CONFIGURATION AND PORT MIRRORING ...................................................................- 27 -
4.11 IGMP SNOOPING .................................................................................................................- 28 -
4.12 VLAN.................................................................................................................................- 28 -
5TIME SYNCHRONIZATION ............................................................................................... - 30 -
5.1 SNTP/NTP SERVER OR IEEE1588 GRANDMASTER............................................................- 30 -
5.2 IEEE1588 TRANSPARENCY.................................................................................................- 30 -
5.3 SNTP TIME CLIENT AND SERIAL TIME SERVER.....................................................................- 30 -
5.4 IRIG-B................................................................................................................................- 31 -
5.5 PULSE PER XSECONDS ON GPS INTERFACE ........................................................................- 31 -
5.6 PULSE PER MINUTE.............................................................................................................- 31 -

V3.8
OnTime Industrial Ethernet
U/R/T200 series Installation Guide
- 4 -
6SERIAL INTERFACE............................................................................................................ - 31 -
6.1 GPS INTERFACE –ACUTIME 2000.......................................................................................- 31 -
6.2 SERIAL TIME SERVER..........................................................................................................- 34 -
7RETURN PROCEDURE........................................................................................................ - 34 -
8UPGRADING OF THE R/T200 SWITCH............................................................................ - 35 -
8.1 INTRODUCTION....................................................................................................................- 35 -
8.2 FTP SERVER CONFIGURATION .............................................................................................- 35 -
8.2.1 Stopping existing FTP servers................................................................................... - 35 -
8.2.2 Configure the FTP server.......................................................................................... - 35 -
8.3 FIRMWARE UPGRADE VIA IP CONFIGURATION TOOL............................................................- 37 -
8.4 FTP SERVER TROUBLESHOOTING.........................................................................................- 38 -
8.4.1 Example 1.................................................................................................................. - 38 -
8.4.2 Example 2.................................................................................................................. - 40 -
8.4.3 Typical problems ....................................................................................................... - 41 -
9SOFTWARE VERSIONS OF THE R/T200 SWITCH........................................................ - 42 -
9.1 INTRODUCTION....................................................................................................................- 42 -
9.2 HOW TO UPGRADE FROM OLD TO NEW MAJOR SOFTWARE VERSION.....................................- 42 -
9.3 IP CONFIGURATION TOOL –SOFTWARE VERSIONS ...............................................................- 44 -

V3.8
OnTime Industrial Ethernet
U/R/T200 series Installation Guide
- 5 -
1 Introduction
This document describes how to install and configure switches in the T200, R200 or U200
series.
This Operator Manual describes the properties of the T200, R200 and U200 series.
1.1 T200
The T200 is the time synchronization switch series of Westermo OnTime. The T200 series
has also full management support including QoS, network redundancy (FRNT protocol),
SNMP, IGMP snooping, VLAN and MAC security. The switches are approved for industrial
use.
All chapters in this document are relevant for the T200 series.
Note: Using the time synchronization, SNMP, IGMP snooping, VLAN and MAC security
management features of the T200 series require minimum network knowledge by the user.
1.2 R200
The R200 series contains the same features as the T200 series except for time
synchronization.
All chapters in this document except chapters 5 and 6 are relevant for the R200 series.
Note: Using the SNMP, IGMP snooping, VLAN and MAC security management features of
the R200 series require minimum network knowledge by the user.
1.3 U200
The U200 series is an unmanaged switch implementation with QoS support (layer 2 and 3).
The U200 switch series has the same approvals for industrial use as the R200 and T200
series.
All chapters in this document except chapters 3.3.8, 4, 5, 6 and 8 are relevant for the U200
series.

V3.8
OnTime Industrial Ethernet
U/R/T200 series Installation Guide
- 6 -
2 Quick Install Guide
2.1.1 Release Notes – Software versions
Information on release notes, software versions, IP Configuration tool and MIB’s can be found
on the CD or www.OnTimenet.com/upgrades.htm
Access to this page requires a user name and a password. This can be obtained by
contacting us on telephone [phone], Fax [phone] or
[email protected] . User name will be given in exchange for information of Customer
name, Switch type/serial number or Order number for the delivery of switches.
2.1.2 Mounting, power and port connections
A quick guide for how to install a U/R/T/200 using DIN rail mounting (default) is as follows:
1. Mounting, see chapter 3.1.1
2. Power connection, see chapter 3.1.5
3. Port connections, see chapter 3.1.6 and 3.1.7
Now the switch is ready for use.
2.1.3 Redundant ring – FRNT0 configuration
Setting up several R/T200 switches in a redundant ring using the FRNT0 protocol requires
switch management configuration via the IP configuration tool. The program is available for
download from OnTime web page: http://www.OnTimenet.com/upgrade.htm.
Extract the .ZIP file to your computer, and start the application from a PC on the network that
you want to configure. Make sure that the IP Address of the configuration software (see figure
below) is in the same sub domain as your PC.

V3.8
OnTime Industrial Ethernet
U/R/T200 series Installation Guide
- 7 -
In a ring configuration as FRNT v0, one, and only one, R/T200 switch must be configured to
be the network Focal Point. The Focal Point switch will then have the role as Redundancy
Manager, and thus be responsible for recovery when a connection between the switches is
broken. To set up a FRNT v0 configuration the following steps must be followed:
1. Define which Switch that shall be the network Focal Point.
2. Power up the switch and connect this to the network.
3. Assign an IP address for the configuration software. Ensure the address range is
within the same Subnet as your assigned IP address for your PC.
4. Press the ‘Scan for devices’ button. The Switches on the network will be listed, see
below.

V3.8
OnTime Industrial Ethernet
U/R/T200 series Installation Guide
- 8 -
5. Run the cursor over the listed Switch and click the mouse to select it.
6. A new configuration Window will open:
7. If required; assign a new IP address and Subnet address for this Switch.
8. Press the ‘Set’ button to assign this IP address and Subnet settings to the Switch.
9. Tick the ‘Enable FRNT Ring’ and ‘Network focal point’ to set the Switch to be the
Focal Point and Bus Member to ensure the Switch configured to run within a
Redundant Ring.
10. Press the ‘Set’ button (all your changes performed will be set).
11. Press the ‘Restart’ button to re-configure the Switch. The Switch will run through the
start sequence. During this period communication to the Switch will be lost.
12. Connect the next Switch into the ring. (This must be connected from Port 8 to Port 7
in a clockwise manner on version 2.30 or older).
13. Press the ‘Scan for devices’ button. The second Switch will appear on the list.
14. Run the cursor over the second Switch and left click the mouse.
15. If required; assign a new IP address and Subnet address for this Switch.
16. Tick ‘Enable FRNT ring’ to ensure the Switch is configured to run within a Redundant
Ring.
17. Press the ‘Set’ button.
18. Press the ‘Restart’ button to re-configure the Switch. The Switch will run through the
start sequence. During this period communication to the Switch will be lost.
19. Continue connecting Switches in this manner until the ring has been completed

V3.8
OnTime Industrial Ethernet
U/R/T200 series Installation Guide
- 9 -
3 Switch Installation and Configuration
3.1 Mounting
3.1.1 DIN rail mounting
The U/R/T200 DIN rail kit is the default mounting kit, and this kit is enclosed in the switch
shipment unless another mounting kit is specified. Both vertical and horizontal mounting is
possible. The DIN rail kit contains the following parts:
- 2 x DIN clips
- 4 x screws
Figure 1 shows vertical and horizontal DIN rail mounting.
Figure 1, DIN rail mounting
Detailed drawings for both vertical (MOUN0004) and horizontal (MOUN0002) DIN rail
mounting are found on http://www.OnTimenet.com/downloads.htm.
Heavy duty DIN clips are also available (improved vibration properties) for horizontal DIN rail
mounting, MOUN0003. This mounting kit must be ordered separately.

V3.8
OnTime Industrial Ethernet
U/R/T200 series Installation Guide
- 10 -
3.1.2 19” dual units mounting
The U/R/T200 wall mounting kit, MOUN0009, contains the following parts:
- 2 x short angle brackets
- 4 x nut brackets
- 2 x H – lists
- 4 x curved nuts
- 4 x rack screws
- 4 x rack brackets
- 8 x brackets
- 8 x screws
Figure 2 shows how to mount two URT200 by using the 19” dual units mounting kit.
This mounting kit must be ordered separately.
Figure 2, 19” dual units mounting kit

V3.8
OnTime Industrial Ethernet
U/R/T200 series Installation Guide
- 11 -
3.1.3 19” single unit mounting
The U/R/T200 wall mounting kit, MOUN0008, contains the following parts:
- 1 x long angle bracket
- 1 x short angle bracket
- 4 x nut brackets
- 4 x curved nuts
- 4 x rack screws
- 4 x rack brackets
- 8 x brackets
- 8 x screws
Figure 3 shows how to mount on U/R/T200 by using the 19” single unit mounting kit.
This mounting kit must be ordered separately.
Figure 3, 19” single unit mounting kit

V3.8
OnTime Industrial Ethernet
U/R/T200 series Installation Guide
- 12 -
3.1.4 Wall mounting
The U/R/T200 wall mounting kit, MOUN0006, contains the following parts:
- 2 x short angle brackets
- 4 x nut brackets
- 8 x brackets
- 8 x screws
Figure 4 shows how to mount the wall mounting kit.
This mounting kit must be ordered separately.
Figure 4, Wall mounting kit

V3.8
OnTime Industrial Ethernet
U/R/T200 series Installation Guide
- 13 -
3.1.5 Power connection
Connect your primary voltage (e.g. +24VDC) to the VinA pin and ground to one of the –COM
pins on the power input on the U/R/T200 switch by using the enclosed power connector.
Figure 5, Power input
3.1.6 Copper drop link connection
Both straight and crossed RJ45 cables can be used for copper connection, see Operator
Manual for details related to the Auto-MDI-X operations.
3.1.7 Fiber drop link connection
Auto-MDI-X is not supported on the fiber ports. Thus, the user must make sure that the fiber
drop link used is crossed. This is easily verified by checking if the fiber port LED is on or not,
when the fiber drop link is connected between two switches or the switch and a fiber enabled
end node. Manual swaping of the TX/RX drop link on one of the fiber devices is required in
case the LED is off on both devices. This can be done either directly on the switch fiber port
or on a fiber patch panel if this is available (preferably).
3.2 Power Supply Connector
3.2.1 Redundant power inputs
The switch is designed to operate permanently over a very wide range of power input (19 V
DC to 60 VDC). Two redundant inputs are provided to provide enhanced redundancy if either
supply fails.
The power supply draws power from the input that has the highest potential difference when
compared to the alternate supply.
This enables use of e.g. a 48V source as primary supply with a 24VDC battery as back up.
Power supply inputs have reverse polarity protection.
The switch is delivered with a power connector (Wieland 25.621.3553.0) that is suitable for
wires between AWG 20 and AWG 22 (0,34-0,5 mm2).

V3.8
OnTime Industrial Ethernet
U/R/T200 series Installation Guide
- 14 -
Figure 6, Power contact
3.2.2 Fault Contact
The switch is incorporated with a user configurable fault contact (STAT pin on the power
contact) that enables network and switch faults to be highlighted.
The user configurable fault contact is a solid state component and therefore requires power to
control the device.
As standard the fault contact will always highlight the following:
•Internal switch watchdog failure.
•Link / Port 7 Failure (if redundant ring mode is activated)
•Link / Port 8 Failure (if redundant ring mode is activated)
•Power Supply Failure
•Focal Point / Redundancy Mode activated.
•Time sync error; NMEA reports or PPS missing on RS232/422 interface
Using the Switch configuration software, the fault contact can highlight the following addition
failures:
•Link / Port 1 to Port 8 Failure
The user can connect to the fault contact, STAT pin on power connector, see Figure 6, with a
pull-up resistor to Vin.
The fault contact implementation is described in details in the Operator Manual.
3.3 Front panel LED’s and Push Buttons
3.3.1 Manual Configuration
The front panel LEDs provides indication on the Status of each port. In addition, each port can
be manually configured for speed, duplex and auto-negotiation can also be set from the push
button panel. The LED/push button panel is shown in the figure below.
Figure 7, LED’s and push buttons

V3.8
OnTime Industrial Ethernet
U/R/T200 series Installation Guide
- 15 -
3.3.2 Normal Indication Mode
When the unit is first powered on the Switch front panel LEDs will run in normal mode. In this
condition the port LED will indicate link and traffic status.
3.3.3 Select Port Mode
The front panel will enter Select Port Mode when the Select Port button is pressed. Pressing
the Select Port button once will illuminate Port 1 LED – manual control of this port is now
available. Pressing the Select Port button a second time will illuminate Port 2 LED – manual
control of this port is now available. Each additional port can be placed into Manual mode by
subsequent pressing of the Select Port button.
If no buttons are pressed for 30 seconds the unit will return back to Normal Indication Mode.
3.3.4 Speed Button
Pressing the Speed button once selects 10M, twice enables 100M.
3.3.5 Duplex Button
Pressing the Duplex button changes the Port duplex mode from full duplex to half duplex and
vice-versa.
3.3.6 Auto-negotiation
Pressing both the Speed and the Duplex button will enable or disable auto-negotiation for the
selected port.
3.3.7 Save Button
Newly configured settings are stored in non-volatile memory when the Save button is
pressed.
Note: Manual configuration of fiber ports is not possible. These ports are configured for full
duplex connectivity and 100 Mbps.

V3.8
OnTime Industrial Ethernet
U/R/T200 series Installation Guide
- 16 -
3.3.8 LED Fault indication
In addition to display port and traffic status, the LED front panel will display fault information if
the switch is managed (U/R200 series). The LED fault indications are as follows:
•HDX LED will blink in case of a FRNT v0 error. I.e. the FRNT v0 ring is not intact.
The focal point or a member switch will indicate that one or both of its FRNT0 ring
ports is not working (link is OFF, or no FRNT v0 packets are received. The HDX LED
will also blink on the FRNT v0 focal point even if its FRNT v0 ports is working if the
FRNT v0 ring is not intact. Relevant in case FRNT v0 (FRNT ring) is enabled in the IP
configuration tool.
•FDX LED will blink in case of a port alarm. Relevant in case port alarm is enabled in
the IP configuration tool.
•100 LED will blink in case of no PPS signal or no NMEA reports from the GPS
receiver is received on the GPS interface. Relevant when time synchronization and
external time base are enabled in the IP configuration tool. The 100 LED will also
blink in case the SNTP client is out of synchronization, relevant in case SNTP client is
selected in the IP configuration tool.
•10 LED will blink in case of an FRNT v1 error. I.e. no communication to remote
FRNT v0 ring via the FRNT v1 enabled port (either primary or secondary FRNT v1
port). Relevant in case FRNT v1 is enabled in the IP configuration tool.
When the fault contact is energised the front panel display will also mimic this status by
strobing one or more the above LEDs. When the fault(s) is cleared the LEDs will automatically
be extinguished.
Figure 8, LED’s and push buttons

V3.8
OnTime Industrial Ethernet
U/R/T200 series Installation Guide
- 17 -
3.4 Fiber optic care
Fiber optic transmission medium is usually made of Glass. In addition, the diameter of the
fiber can be as low as 9um. In comparison, the diameter of an average piece of Human hair is
40 um.
Therefore, a small piece of dust or contaminate located on the end of a patch cable
could easily disrupt communications. Permanent damage to both fiber patch cords and
fiber optic transceiver components may be the result of just a small invisible piece of
dust!
The fiber optic transceivers and associated patch cables must be treated with great care.
Therefore, the following rules should be adhered to during any commissioning work and fiber
optic installation.
•Dust caps must be replaced immediately after removal of patch cable from
transceiver or patch box. Failure to comply could result in damage to transceivers or
patch cables.
•Keep hands clean when touching fiber optic cable.
•Patch cables should be cleaned with IPA and dried with a lint-free cloth before
installation.
•Once patch cables have been installed dust will not ingress the transceiver

V3.8
OnTime Industrial Ethernet
U/R/T200 series Installation Guide
- 18 -
4 IP Configuration Software
The Westermo OnTime Switches are configured using supplied software. The program is
available for download from OnTime web page: http://www.OnTimenet.com/upgrade.htm.
Extract the .ZIP file to your computer, the application is called IP configuration.
Start the application from a PC on the network. Make sure that the IP Address of the
configuration software (see figure below) is in the same sub domain as your PC.
Figure 9
By clicking the Scan for switches button the IP Configuration Software will detect the switches
in the IP subnet. The information in the figure below will appear for each switch.
•IP Address Of
Configuration
Software
•Scan For
Switches To
Find And
Configure Focal
Point Switch

V3.8
OnTime Industrial Ethernet
U/R/T200 series Installation Guide
- 19 -
Figure 10
By clicking on the line for each respective switch, further configuration opportunities will
appear. See below.
Figure 11
•First Switch
Found
•Switch IP
Address
•Switch MAC
Address
•Firmware
Revision
•Configuration
Style
•Ring Status

V3.8
OnTime Industrial Ethernet
U/R/T200 series Installation Guide
- 20 -
After choosing one of the switches to be the FRNT Primary switch it will appear like the first
one in the list below. For further information about FRNT v0 see section 3.1
Figure 12
If the ring should be broken the Status of the Focal Point switch will change from RING to
BUS. An exclamation mark will be shown on the ports that have lost connection.
Figure 13
•Scanning For
Devices Highlights
All Switches On
Ring
•Highlights FP
Running Network
As A ‘Ring’
•Highlights Network
Focal Point
•Switch software
version
•Scanning For
Devices Highlights
All Switches On
Ring
•Ring Failure
Occurred
•FP Now Running
As Bus
•Highlights Link /
Port That Have
Failed