Westomatic Primo Compact Instruction sheet

WATER RESERVOIR
INSTALL & USE
COMPACT
COMPACT

INSTALL WATER RESERVOIR
External Dimensions Water
Reservoir:
W230xD420xH455mm
External Dimensions Total:
W530xD515xH600mm
Capacity Water Reservoir:
8.2litres/5.2litres with the
Filter
The water reservoir allows the
machine to be used without
mains water connection:

Parts Included:
Water Reservoir
Water Container
Water Hose
Hose Connector x2
Internal Power cable (red &
purple wire)
Power cable (black)
User manual
Brita Filter & cartridge
(optional use)
OPTIONAL: Ingredient Box
PN: 1057339
Check the contents:
NB: The machine will have been set up to your specifications and tested at Westomatic
HQ prior to install. All parts have been assembled on the machine. The QR code inside
the machine gives access to the We:Support pages with technical information.

Remove the
cover plate for
the power cable
feed through
Remove the
screws from
the back cover
Locate the
power pins -
remove the red
and purple wire
connectors
Switch off and
UNPLUG the
Primo Compact
from the mains
power
Place the Water
reservoir on a
level surface
Min Clearances:
Rear: 50mm
Ensure the
protective
plastic is
removed from
the top

11
Connect the
internal power
cord to the plugs
Red-Red/Purple-
Purple
Place plugs back
on power pins
Replace the
back cover -
and fasten the
two screws
Guide the internal
power cable to
the opening in
back cover and
push through
Remove the red
cover from the
water entry on
the Primo
12
Attach water
connector and
tighten

14
16
15
13
17
Insert the water
hose in the
connector
Insert water hose
into the water
connector and
then attach to the
water reservoir
Connect the
Primo to the
power outlet and
Switch on
Connect the
Primo and the
water reservoir
with the external
power cable
Water
Reservoir is
now installed

USING THE RESERVOIR:
Ensure the Water Reservoir is
clean before every refill
The reservoir is dishwasher
safe to max 50°C
NB. The Brita filter lid should
be cleaned by hand (if using)
These instructions show how to
commission the reservoir to use :

Fit filter into the
Brita Filter lid
(If using)
Fill container
with water:
8.2litres Total
(5.2liters with
filter)
Place the water
tank into the
unit and push
to the back
There is space
under the tank
for spare water
filters
On the main
screen select
the Main Menu
Close the lid

11
Select OPERATOR
MENU
Enter Operator
Pin-Code
Default = 11111
Enter Pin-Code
again to enter
Service Menu
Choose
SERVICE MENU
(1.07)
Select SETTINGS
(2.04)
Select EXTERNAL
WATER TANK
(2.04.19)
12
Switch to
ACTIVE,
Select WATER
RESERVOIR,
Press SAVE

Water Reservoir is now set up and
ready to use.
It is possible to use both the Water
Reservoir and the Fresh Milk Fridge
at the same time for the full
experience.

W e s t o m a t i c V e n d i n g
S e r v i c e s L t d ,
U n i t s 7 - 8 F o r d e C o u r t ,
B l o c k 4 F o r d e R o a d ,
N e w t o n A b b o t ,
T Q 1 2 4 B T
+ 4 4 ( 0 ) 1 6 2 6 3 2 3 1 0 0
s a l e s @ w e s t o m a t i c . c o m
w w w . w e s t o m a t i c . c o m
C O N T A C T