WETJET WJ85.402.050 User manual

User Manual
WJ85.402.050
Hand Crank Hose Reel
85.610.701

GENERAL SAFETY REGULATIONS
WARNING: The warnings, cautions, and instructions
discussed in this instruction manual cannot cover all
possible conditions or situations that could occur. It
must be understood by the operator that common
sense and caution are factors that cannot be built into
this product, but must be supplied by the operator.
1. Keep the work area clean and dry. Damp or wet work areas can result in injury.
2. Keep children away from work area. Do not allow children to handle this
product.
3. Use the right tool for the job. Do not attempt to force small equipment to do
the work of larger industrial equipment. There are certain applications for
which this equipment was designed. It will do the job better and more safely
at the capacity for which it was intended. Do not modify this equipment, and
do not use this equipment for a purpose for which it was not intended.
4. Check for damaged parts. Before using this product, carefully check that it
will operate properly and perform its intended function. Check for damaged
parts and any other conditions that may affect the operation of this product.
Replace damaged or worn parts immediately.
5. Do not overreach. Keep proper footing and balance at all times to prevent
tripping, falling, back injury, etc.
6. DO NOT use the equipment when tired or under the influence of drugs,
alcohol, or medication. A moment of inattention while operating this
equipment may result in serious personal injury.
WARNING
1. Read carefully and understand the manual of the pressure washer that you
will be using with this hose reel and follow all the safety concerns and warnings
in the pressure washer manual.
2. Read carefully and understand all assembly and operation instructions before
operating. Failure to follow the safety rules and other basic safety precautions
may result in serious personal injury.
3. Never modify any part of the hose reel and replace damaged or worn parts
immediately otherwise further damage or injury may occur.
4. Never exceed the maximum ratings of the hose reel or the hose that has been
used with it.

TECHNICAL DETAILS
Read the following precautions and instructions before you begin assembly or using. Keep this
literature in a dry place for future reference.
ASSEMBLY
Max Hose Diameter**
Max Hose Length**
Max PSI**
Max Temp**
Inlet Size**
Outlet Size**
3/8"
50'
4000
78°C/160°F
3/8"
3/8"
E1
TECHNICAL
DETAILS
SAFETY
PRECAUTIONS
ASSEMBLY UNPACKING
L202&H202
11"/285mm
4.2"/108mm
3"/84mm
14"/350mm
11"/285mm
8"/200mm
4"/100mm
3"/84mm
4"/100mm
13"/330mm
4"/100mm
**Hose not included**
This hose reel will come mostly preassembled. The only part that will need to be added is the
cranking handle. The cranking handle will be packaged separately and will include all the
mounting hardware. The alignment of the holes is designed to allow it to be mounted only
one way on the outside of the hose reel. Use a PHILLIPS screwdriver and a wrench to
secure tightly.
Mounting it to your pressure washer
Note: You must purchase extra hardware and hose to mount this hose reel.
1. The unit will have a mounting bracket with four predrilled holes. This will allow it to be
mounted on any flat surface that can support its weight.
2. Depending on your pressure washer design, it may also mount directly on the upper frame
plate. You may need to remove decals and/or drill holes to match up to the pattern of the
hose reel.
3. Use nuts and bolts (not included) to attach the hose reel to where it is being mounted.
4. The 3/8” MNPT brass fitting at the bottom of the hose reel is the inlet. Connect this fitting to
your pressure washer pump. (You may need to purchase fittings and an extra hose.)
5. The hose reel can accommodate up to a 3/8” x 50’ hose (sold separately). Thread one end
of the hose from the inside of the hose reel, through the slot, and then to the brass swivel
fitting. Use Teflon tape to secure the fitting and help prevent leaking.
6. Use the provided hose clamp to secure the hose going from the fitting through the slot.
It is strongly recommended to give the hose some slack to minimize stresses on the fitting
from the angles.
7. Wrap up the hose in the hose reel.
EXPLODED AND
PARTS LIST
TROUBLESHOOTING
AND WARRANTY

TROUBLESHOOTING
E2
EXPLODED AND
PARTS LIST UNPACKING
TROUBLESHOOTING
AND WARRANTY
Problem(s)
Leaking water
Water leaking through
swivel
Swivel assembly not
moving freely
(locking up).
Possible Cause
a) Fittings need to be sealed
with teflon tape.
b) Hose has burst.
a) Fittings need to be sealed
with teflon tape.
b) Too much tension on swivel.
Inlet hose is not flexible causing
side force on swivel.
Corrective Action
a) Identify fittings, tape threads
with teflon tape.
b) Replace hose.
a) Identify fittings, tape threads
with teflon tape.
b) Replumb so that there is more
slack on the hose that is
connected to it.
Properly tighten inlet hose.
Hand tighten fitting, plus another
half turn with wrench.
WARRANTY
This hose reel unit has a three months limited warranty. This warranty covers manufacturer
defects only and does not extend to any damage caused by the user. It also does not extend
to any wear and tear caused by regular use of the product.
TECHNICAL
DETAILS
SAFETY
PRECAUTIONS
ASSEMBLY

EXPLODED AND PARTS LIST
Part No.
1
2
3
4
5
6
7
8
9
10
11
12
Description
Base(welded with stand)
Stand(steel pipe covered with foam protector)
Fixed washer (welded on stand)
Washer
Positon sleeve
Flange A
Sleeve
Flange B
Position sleeve
Washer
Spring
Washer
Q’ty
1
1
1
1
1
1
1
1
1
1
1
1
Part No.
13
14
15
16
17
18
19
20
21
22
23
24
Description
Swivel (including 2 valve & 2 O-ring)
Spring wahser
Nut
Washer
Protector (rubber)
Clamp
Screw
Screw
Washer
Nut
Handle
Valve
Q’ty
1
1
3
3
1
1
3
3
3
3
1
1
E3
EXPLODED AND
PARTS LIST UNPACKING
TROUBLESHOOTING
AND WARRANTY
TECHNICAL
DETAILS
SAFETY
PRECAUTIONS
ASSEMBLY

If you need assistance with the assembly
operation of your Hand Crank Hose Reel please call
1-866-850-6662