Whale F600 User manual

OWNER’S MANUAL
FOR
WATER HEATERS
CAUTION: READ INSTRUCTIONS BEFORE OPERATING APPLIANCE.
MODEL: F600, F650, F750, F1100, F1150, F1200,
F1250, H2000, H2050, H2200, H2250,
H2850, HF2000, HF2050, HF2200, HF2250,
S600, S650, S700, S750, S1100, S1150,
S1200, S1250, S1800, S1900
75545 Rev. C

1
IMPORTANT SAFETY INSTRUCTIONS
WARNING
When using electrical appliances, basic safety precautions to reduce the risk of re,
electrical shock, or injury to persons should be followed, including:
1. READ ALL INSTRUCTIONS BEFORE USING THIS WATER HEATER.
2. This water heater must be grounded. Connect only to properly grounded source.
See "GROUNDING INSTRUCTIONS" found on Page 4, Item 7.
3 Install or locate this water heater only in accordance with the provided installation
instructions.
4. Use this water heater only for its intended use as described in this manual.
5. Do not use an extension cord set with this water heater. If no junction box is available
adjacent to the water heater, contact a qualied electrician to have one properly
installed.
6. As with any appliance, close supervision is necessary when used by children.
7. Do not operate this water heater if it has a damaged power supply line, if it is not
working properly, or if it has been damaged or dropped.
8. This water heater should be serviced only by qualied service personnel. Contact
nearest authorized service facility for examination, repair, or adjustment.
WARNING
This water heater is equipped with a heat exchanger. Extended engine coolant circulation
through the heater may result in excessively hot water.
This water heater tank and heat exchanger is made of aluminum. Some engine
manufacturers recommend that cooling system be ushed periodically. Caustic chemicals
are commonly used. DO NOT ush caustic chemicals (such as Nalcool) through your
system with the heat exchanger hooked up or damage WILL occur to heater.
If ushing is required by your engine manufacturer, you must isolate heater from this
process. After system ushing is complete and neutralized, you can then re-plumb heater.
Make sure recommended automotive type premixed ethylene glycol coolants such as
Prestone, Xerex, or Peak are used for replacement. Damage that occurs to heater due
to chemical reaction by caustic chemicals IS NOT under warranty.

2
CAUTION
Hydrogen gas can be produced in a hot water system served by these heaters that
have not been used for a long period of time (generally 2 weeks or more). Hydrogen
gas is extremely ammable. To reduce the risk of injury under these conditions, it is
recommended that the hot water faucet be opened for several minutes at the kitchen
sink before using any electrical appliance connected to the hot water system. If hydrogen
is present, there will be an unusual sound such as air escaping through the pipe as the
water begins to ow. There should be no smoking or open ame near the faucet at the
time it is open.
Small amounts of electric currents may move to your boat through your shore cord,
causing galvanic damage to your water heater. To help prevent possible damage, a
galvanic isolator is recommended. Galvanic corrosion IS NOT covered under warranty.
ANODES
In a small number of instances tap water may have sufcient concentrations of dissolved
salts to cause corrosion of the heater tank. Anode rods preserve the life of a water heater
by corroding themselves so the water heater doesn’t. These anode rods are easy to
install! Simply replace the drain plug with this product to protect the water heater tank.
Note:
DO NOT USE ZINC ANODES. THEY WILL NOT PREVENT
CORROSION TO YOUR HEATER TANK!!!!
If you live in an area known to have such water please contact our customer service
department at 616-897-9241 to order a Magnesium Anode.
Part No. 74556, Magnesium 4" Anode with 3/4" thread to replace drain valve.
ANODE PART # 74556
REPLACES DRAIN
VALVE PART # 73123
HOT WATER OUTLET
DRAIN
***REMOVE DRAIN AND
REPLACE WITH ANODE
P & T VALVE
COLD WATER INLET

3
NOTICE
This temperature / pressure valve may weep during initial operation. This is normal. The
valve will seat itself with use. A drain hose should be installed at this valve and directed
overboard.
If the boat is connected to the dockside water system, make sure to turn off the system
at the dock when not attended. Also make sure a pressure regulator is used to control
pressure.
OPERATING INSTRUCTIONS
1. Fill water system and completely ll tank.
2. Locate and turn remote electrical switch to "ON".
3. Turn switch to "OFF" position prior to draining water system.
4. The temperature / pressure valve may weep during initial operation. This is normal.
The valve will seat itself with use.
NOTE: DO NOT OPERATE HEATER WITHOUT ELEMENT BEING SUBMERGED IN WATER
MAINTENANCE
1. Check heat exchanger lines for leaks at regular intervals. A leak in the system will
cause coolant loss and may damage engine.
2. Flush tank periodically to help prevent build-up of deposits.
3. Protect against damage from freezing temperatures (32° F or less)
Please review the following:
a) Drain tank by fully opening drain valve. Open T&P valve to help relieve vacuum
in tank. (See item 2 in exploded view)
b) It is recommended you winterize your fresh water system. First complete step
3a, then follow instructions of your local supplier regarding chemicals to use
and how to use them.
CAUTION
If heater has been run without water and now fails to work, ll heater tank with water and push
electric reset button high limit switch under wire access cover before calling for service.

4
INSTALLATION
NOTE: DO NOT INSTALL THE WATER HEATER ON ITS SIDE OR UPSIDE DOWN
1. Locate water heater at engine level as close to engine as possible.
2. Secure mounting brackets to structure with eight #12 minimum screws or 1/4 - 20
minimum cap screws and nuts.
3. Connect cold water supply and hot water outlet to heater as marked, 1/2" N.P.T.
ttings.
4. Connect heat exchanger system described in Figure 1. Make sure coolant system is
completely purged of air and full of coolant before operating.
5. Pressure temperature relief valve is factory installed. The pressure relief shall limit the
pressure to 127.5 PSI (879.3 KPA) minimum, 150 PSI (1034.2 KPA) maximum.
The valve must be oriented, provided with tubing, or otherwise installed so that
discharge can exit no more than 6 inches above, or at any distance below the structural
oor, and cannot contact any live electrical part.
Install replacement temperature and pressure protective equipment required by local
codes, but not less than a combination temperature and pressure relief valve certied
as meeting the requirements for relief valves and automatic gas shutoff devices for
hot water supply systems, ANSI Z21.22 by a nationally recognized testing laboratory
that maintains periodic inspection of production of listed equipment or materials.
6. Connect the electrical supply by a qualied electrician. The electrical supply shall be
permanent wiring, armored cable or conduit, per national electrical code NFPA 70,
with a minimum capacity of 1500 watts.
On 120 volt circuits, use a UL approved 15 amp circuit breaker. On 240 volt circuits,
use a 10 amp approved circuit breaker per leg.
7. GROUNDING INSTRUCTIONS: The supply ground shall be connected to the green
wire located in the water heater wiring compartment. Do not place switch in the
grounding circuit.
8. RESET INSTRUCTIONS: The heater is equipped with a high limit switch which can
be manually reset. If the limit switch activates, proceed as follows:
• Turn power off at main power panel or remote switch
• Remove wiring access cover
• Depress red button on high temperature limit switch
• Replace cover and turn power on
• If temperature limit switch reactivates, contact a Whale-Seaward
Authorized service center.

5
WIRING DIAGRAM FOR 120V
WIRING DIAGRAM FOR 240V

6
Winterizing Your Whale®Heat Water Heater
Winterizing your fresh water system is an essential procedure that will maintain the life and longevity
of your Whale Heat water heater and fresh water tanks. To ensure that your fresh water system has
adequate protection for winter storage, use the following recommended winterizing procedure.
Winterizing the Water Heater and Fresh Water System
1. Locate the fresh water tank drain valve or plug and allow the fresh water tanks to drain until
approximately 115% to 120% of the water heater capacity remains in the tanks.
Example: If water heater is 11 gallons = 12 to 13 gallons in fresh water tanks.
2. Treat the remaining fresh water left in the fresh water tanks with "Winterizing Chemicals".
Winterizing chemicals are non-toxic antifreeze that is a propylene-glycol base and are safe for
portable water systems.
NOTICE
DO NOT USE THE TYPE OF ANTI-FREEZE THAT IS USED TO WINTERIZE
AUTOMOBILES. THIS IS NOT SAFE FOR PORTABLE WATER SYSTEMS.
NOTICE
Antifreeze can be very corrosive to the anode rode. The result will be accelerated
deterioration of the rod and heavy sediment in the tank. If you intend to winterize by
adding antifreeze into the system and your water heater is equipped with an anode,
remove the anode rode (storing it for the winter) and replace it with a 3/4" male pipe
thread drain plug.
3. Turn off 120V or 240V AC power.
4. Turn on fresh water pump.
5. Open each faucet and water outlet one at a time until winterizing chemical is apparent at the
opening.
6. Turn off fresh water pump and leave all faucets and water outlets open over winter.
7. Locate the water heater drain and pressure relief valve and allow all water to drain from water
heater until empty. Leave water heater drain and pressure relief valve open over winter.
CAUTION
SPECIAL PRECAUTIONS MUST BE USED WHEN DRAINING AND FILLING
AN ELECTRIC WATER HEATER. ELECTRICITY MUST BE TURNED OFF
BEFORE DRAINING AND REFILLING WATER HEATER TANKS.

7
De-Winterizing the Water Heater and Fresh Water System
1. Close all faucets, water outlets, the water heater drain and pressure relief valve.
2. If during the winterizing procedure the anode was removed and replaced with a 3/4" male pipe
thread drain plug, remove the drain plug and replace with anode.
3. Fill fresh water tanks with fresh water approximately so that 115% to 120% of the water heater
capacity remains in the fresh water tanks.
Example: If water heater is 11 gallons = 12 to 13 gallons in fresh water tanks.
CAUTION
SPECIAL PRECAUTIONS MUST BE USED WHEN DRAINING AND FILLING
AN ELECTRIC WATER HEATER. ELECTRICITY MUST BE TURNED OFF
BEFORE DRAINING AND REFILLING WATER HEATER TANKS.
4. Turn on fresh water pump.
5. Open each faucet and water outlet one at a time until winterizing chemical is no longer apparent
at the opening. This allows the fresh water to ush the winterizing chemicals out of the fresh
water system.
6. Fill fresh water tanks to 100% capacity.
NOTICE
Whale Heat recommends that while lling the fresh water storage tanks that a
small amount of common household bleach be added to the fresh water system to
control the possible growth of algae. If an algae condition starts it is very difcult
to control.
Example: 1 oz. of bleach for every 50 gallons of fresh water.
7. Fresh water system is now de-winterized and ready for use.

8
ITEM MODEL NO. PART NO. DESCRIPTION
1 ALL MODELS 80727 TANK ASSEMBLY
2 ALL MODELS 73127 TEMPERATURE/PRESSURE VALVE
3 ALL MODELS 73124 GASKET, HEATING ELEMENT
4S300W 75586 1250W HEATING ELEMENT
5S300W 74563 HIGH LIMIT SWITCH, 120V
6 ALL MODELS 73129 THERMOSTAT
7S300W 73148 PLATE, THERMOSTAT MOUNTING 120V
8 ALL MODELS 73123 DRAIN VALVE
9ALL MODELS 73145 SHIELD, WIRES
10 ALL MODELS 75552 WRAP, WHITE
11 ALL MODELS 73290 BACK PANEL, WHITE
12 ALL MODELS 80652 FRONT PANEL, WHITE
13 ALL MODELS 75553 BASE, WHITE
14 ALL MODELS 74669 ACCESS, COVER WHITE
15 ALL MODELS 73146 INSULATION, WRAP
16 ALL MODELS 73147 INSULATION, FRONT
17 ALL MODELS 73330 INSULATION, BACK
PARTS LIST MODELS
S300W

PARTS LIST MODELS
H2000, H2050, H2200, H2250, HF2000, HF2050, HF2200, HF2250
H2000E, H2050E, H2200E, H2250E
ALL MODELS ENDING WITH AN “E” ARE ELECTRIC ONLY
SEE PAGE 10 FOR PART LIST BREAKDOWN
9

ITEM MODEL NO. PART NO. DESCRIPTION
1
H2000 / H2050 / H2200 / H2250 80355 TANK ASSEMBLY
H2000E / H2050E / H2200E /H2250E E80355E TANK ASSEMBLY ELECTRIC ONLY
HF2000 / HF2050 / HF2200 /HF2250 80351 TANK ASSEMBLY
2 ALL MODELS 73127 TEMPERATURE/PRESSURE VALVE
3 ALL MODELS 73124 GASKET, HEATING ELEMENT
4ALL 120V MODELS 74031 1500W HEATING ELEMENT
ALL 240V MODELS 74032
5ALL 120V MODELS 74563 HIGH LIMIT SWITCH
ALL 240V MODELS 74607
6 ALL MODELS 73129 THERMOSTAT
7ALL 120V MODELS 73148 PLATE, THERMOSTATE MOUNTING
ALL 240V MODELS 73171
8 ALL MODELS 73123 DRAIN VALVE
9ALL MODELS 73145 SHIELD, WIRES
10
H2000 / HF2000 / H2050 / HF2050 74000 WRAP, GALVANIZE
H2000 / HF2000 / H2050 / HF2050 74675 WRAP, WHITE
H2200 / HF2200 / H2250 / HF2250 74001 WRAP, S.S.
11
H2000 / H2050 73169 BACK PANEL, GALVANIZE
H2000 / H2050 / HF2000 / HF2050 74667 BACK PANEL, WHITE
H2200 / H2250 73290 BACK PANEL, S.S.
HF2000 / HF2050 73941 BACK PANEL, GALVANIZE
HF2200 / HF2250 73942 BACK PANEL, S.S.
12
H2000 / H2050 80654 FRONT PANEL, GALVANIZE
H2000 / H2050 80658 FRONT PANEL, WHITE
H2200 / H2250 80657 FRONT PANEL, S.S.
HF2000 / HF2050 80655 FRONT PANEL, GALVANIZE
HF2000 / HF2050 80659 FRONT PANEL, WHITE
HF2200 / HF2250 80656 FRONT PANEL, S.S.
13
H2000 / H2050 / HF2000 / HF2050 74002 BASE, GALVANIZE
H2000 / H2050 / HF2000 / HF2050 74668 BASE, WHITE
H2200 / H2250 / HF2200 / HF2250 74003 BASE, S.S.
14 ALL MODELS
73141 ACCESS, COVER GALVANIZE
73291 ACCESS, COVER S.S.
74669 ACCESS, COVER WHITE
15 ALL MODELS 74616 INSULATION, WRAP
16 H2000 / H2050 / H2200 / H2250 73176 INSULATION, FRONT
HF2000 / HF2050 / HF2200 / HF2250 74227
17 H2000 / H2050 / H2200 / H2250 73331 INSULATION, BACK
HF2000 / HF2050 / HF2200 / HF2250 74228
10

11
ITEM MODEL NO. PART NO. DESCRIPTION
1H2850ES-3000, H2850ES-4500 80491 TANK ASSEMBLY
H2850EW-3000, H2850EW-4500 80491 TANK ASSEMBLY
2 ALL MODELS 73127 TEMPERATURE/PRESSURE VALVE
3 ALL MODELS 73124 GASKET, HEATING ELEMENT
4H2850ES-3000, H2850EW-3000 74715 3000W HEATING ELEMENT
H2850ES-4500, H2850EW-4500 75086 4500W HEATING ELEMENT
5240V 74607 HIGH LIMIT SWITCH
6 ALL MODELS 73129 THERMOSTAT
7 ALL MODELS 73171 PLATE, THERMOSTATE MOUNTING
8 ALL MODELS 73123 DRAIN VALVE
9ALL MODELS 73145 SHIELD, WIRES
10 H2850ES-3000, H2850ES-4500 75234 WRAP, S.S.
H2850EW-3000, H2850EW-4500 75055 WRAP, WHITE
11 H2850ES-3000, H2850ES-4500 73290 BACK PANEL, S.S.
H2850EW-3000, H2850EW-4500 74667 BACK PANEL, WHITE
12 H2850ES-3000, H2850ES-4500 73289 FRONT PANEL, S.S.
H2850EW-3000, H2850EW-4500 74666 FRONT PANEL, WHITE
13 H2850ES-3000, H2850ES-4500 75235 BASE, S.S
H2850EW-3000, H2850EW-4500 75056 BASE, WHITE
14 H2850ES-3000, H2850ES-4500 73291 ACCESS, COVER S.S.
H2850EW-3000, H2850EW-4500 74669 ACCESS, COVER WHITE
15 ALL MODELS 74616 INSULATION, WRAP
16 ALL MODELS 73176 INSULATION, FRONT
17 ALL MODELS 73331 INSULATION, BACK
PARTS LIST MODELS
H2850EW-3000, H2850EW-4500, H2850ES-3000, H2850ES-4500

12
PARTS LIST MODELS
S1800 / S1850 / S1900 / S1950
SEE PAGE 13 FOR PART LIST BREAKDOWN

13
ITEM MODEL NO. PART NO. DESCRIPTION
1 ALL MODELS 80263 TANK ASSEMBLY
2 ALL MODELS 73127 TEMPERATURE/PRESSURE VALVE
3 ALL MODELS 73124 GASKET, HEATING ELEMENT
4S1800 / S1900 74031 1500W HEATING ELEMENT 120V
S1850 / S1950 74032 1500W HEATING ELEMENT 240V
5S1800 / S1900 74563 HIGH LIMIT SWITCH 120V
S1850 / S1950 74607 HIGH LIMIT SWITCH 240V
6 ALL MODELS 73129 THERMOSTAT
7S1800 / S1900 73148 PLATE, THERMOSTAT MOUNTING
S1850 / S1950 73171
8 ALL MODELS 73123 DRAIN VALVE
9ALL MODELS 73145 SHIELD, WIRES
10
S1800 / S1850 73395 WRAP, GALVANIZE
S1800 / S1850 74687 WRAP, WHITE
S1900 / S1950 73405 WRAP, S.S.
11
S1800 / S1850 73396 BOTTOM PANEL, GALVANIZE
S1800 / S1850 74688 BOTTOM PANEL, WHITE
S1900 / S1950 73406 BOTTOM PANEL, S.S
12
S1800 / S1850 73397 FRONT PANEL, GALVANIZE
S1800 / S1850 74690 FRONT PANEL, WHITE
S1900 / S1950 73407 FRONT PANEL, S.S.
13
S1800 / S1850 73398 TOP PANEL, GALVANIZE
S1800 / S1850 74689 TOP PANEL, WHITE
S1900 / S1950 73408 TOP PANEL, S.S.
14
S1800 / S1850 73141 ACCESS, COVER GALVANIZE
S1800 / S1850 74669 ACCESS, COVER WHITE
S1900 / S1950 73293 ACCESS, COVER S.S.
15 ALL MODELS 73404 INSULATION, BOTTOM
16 ALL MODELS 73409 INSULATION, WRAP
17 ALL MODELS 73404 INSULATION, TOP

14
PARTS LIST MODELS
S1800E / S1850E / S1900E / S1950E
SEE PAGE 15 FOR PART LIST BREAKDOWN

15
ITEM MODEL NO. PART NO. DESCRIPTION
1 ALL MODELS 80263E TANK ASSEMBLY
2 ALL MODELS 73127 TEMPERATURE/PRESSURE VALVE
3 ALL MODELS 73124 GASKET, HEATING ELEMENT
4S1800E / S1900E 74031 1500W HEATING ELEMENT 120V
S1850E / S1950E 74032 1500W HEATING ELEMENT 240V
5S1800E / S1900E 74563 HIGH LIMIT SWITCH 120V
S1850E / S1950E 74607 HIGH LIMIT SWITCH 240V
6 ALL MODELS 73129 THERMOSTAT
7S1800E / S1900E 73148 PLATE, THERMOSTAT MOUNTING
S1850E / S1950E 73171
8 ALL MODELS 73123 DRAIN VALVE
9ALL MODELS 73145 SHIELD, WIRES
10
S1800E / S1850E 73395 WRAP, GALVANIZE
S1800E / S1850E 74687 WRAP, WHITE
S1900E / S1950E 73405 WRAP, S.S.
11
S1800E / S1850E 73396 BOTTOM PANEL, GALVANIZE
S1800E / S1850E 74688 BOTTOM PANEL, WHITE
S1900E / S1950E 73406 BOTTOM PANEL, S.S
12
S1800E / S1850E 80661 FRONT PANEL, GALVANIZE
S1800E / S1850E 80664 FRONT PANEL, WHITE
S1900E / S1950E 80663 FRONT PANEL, S.S.
13
S1800E / S1850E 73398 TOP PANEL, GALVANIZE
S1800E / S1850E 74689 TOP PANEL, WHITE
S1900E / S1950E 73408 TOP PANEL, S.S.
14
S1800E / S1850E 73141 ACCESS, COVER GALVANIZE
S1800E / S1850E 74669 ACCESS, COVER WHITE
S1900E / S1950E 73293 ACCESS, COVER S.S.
15 ALL MODELS 73404 INSULATION, BOTTOM
16 ALL MODELS 73409 INSULATION, WRAP
17 ALL MODELS 73404 INSULATION, TOP

16
PARTS LIST MODELS
S600, S650, S700, S750, F600, F650, F700, F750
S1100, S1150, S1200, S1250, F1100, F1150, F1200, F1250
ITEM MODEL NO. PART NO. DESCRIPTION
1
S600 / S700 80253
TANK ASSEMBLY
F600 / F700 80309
S1100 / S1200 80254
F1100 / F1200 80310
2 ALL MODELS 73127 TEMPERATURE/PRESSURE VALVE
3 ALL MODELS 73124 GASKET, HEATING ELEMENT
4ALL 120V MODELS 74031 1500W HEATING ELEMENT
ALL 240V MODELS 74032
5ALL 120V MODELS 74563 HIGH LIMIT SWITCH
ALL 240V MODELS 74607
6 ALL MODELS 73129 THERMOSTAT
7ALL 120V MODELS 73148 PLATE, THERMOSTAT MOUNTING
ALL 240V MODELS 73171
8 ALL MODELS 73123 DRAIN VALVE
9ALL MODELS 73145 SHIELD, WIRES
10
S600 / S650 / F600 / F650 73137 WRAP, GALVANIZE
S600 / S650 / F600 / F650 74661 WRAP, WHITE
S700 / S750 / F700 / F750 73283 WRAP, S.S.
S1100 / S1150 / F1100 / F1150 73166 WRAP, GALVANIZE
S1100 / S1150 / F1100 / F1150 74665 WRAP, WHITE
S1200 / S1250 / F1200 / F1250 73287 WRAP, S.S.
11
S600 / S650 73140 BOTTOM PANEL, GALVANIZE
F600 / F650 73888
S600 / S650 74681 BOTTOM PANEL, WHITE
F600 / F650 74663
S700 / S750 73286 BOTTOM PANEL, S.S.
F700 / F750 73887
S1100 / S1150 73169 BACK PANEL, GALVANIZE
F1100 / F1150 73941
S1100 / S1150 74691 BACK PANEL, WHITE
F1100 / F1150 74667
S1200 / S1250 73290 BACK PANEL, S.S.
F1200 / F1250 73942
ITEM MODEL NO. PART NO. DESCRIPTION
12
S600 / S650 80648 FRONT PANEL, GALVANIZE
F600 / F650 80649
S600 / S650 80652 FRONT PANEL, WHITE
F600 / F650 80653
S700 / S750 80650 FRONT PANEL, S.S.
F700 / F750 80651
S1100 / S1150 80654 FRONT PANEL, GALVANIZE
F1100 / F1150 80655
S1100 / S1150 80658 FRONT PANEL, WHITE
F1100 / F1150 50659
S1200 / S1250 80657 FRONT PANEL, S.S.
F1200 / F1250 80656
13
S600 / S650 / F600 / F650 73138 BASE, GALVANIZE
S600 / S650 / F600 / F650 74664 BASE, WHITE
S700 / S750 / F700 / F750 73284 BASE, S.S.
S1100 / S1150 / F1100 / F1150 73170 BASE, GALVANIZE
S1100 / S1150 / F1100 / F1150 74668 BASE, WHITE
S1200 / S1250 / F1200 / F1250 73288 BASE, S.S.
14 ALL MODELS
73141 ACCESS, COVER GALVANIZE
73291 ACCESS, COVER S.S.
74669 ACCESS, COVER WHITE
15 S600 / F600 / S700 / F700 73146 INSULATION, WRAP
S1100 / F1100 / S1200 / F1200 73175
16
S600 / S700 73147
INSUALTION, FRONT
F600 / F700 74225
S1100 / S1200 73176
F1100 / F1200 74227
17
S600 / S700 73330
INSULATION, BACK
F600 / F700 74226
S1100 / S1200 73331
F1100 / F1200 74228

LIMITED TWO YEAR WARRANTY
WHALE®HEAT warrants the products delivered will be:
A. Free from (1) encumbrances and (2) defects in material and workmanship under the normal
use and service.
B. Will meet applicable specications and descriptions at time of delivery to BUYER.
The obligation of WHALE HEAT under this warranty is limited to the repair, rework, or replacement at WHALE
HEAT’S option, any part or component thereof, which examination discloses to our satisfaction to have been
nonconforming or defective. WHALE HEAT, after establishing customer’s purchase date and determining problem
to be under warranty, will either repair the product at their factory or authorized service center and allow labor
and parts for (2) two years from purchase date. Transportation charges are the responsibility of the customer.
Conditions not covered under warranty are:
(1) Corrosion due to electrolysis
(2) Cracking of the tank due to freezing water
(3) Routine maintenance that may be required
The foregoing warranty and condition shall apply to any repaired, reworked, or replaced products, part or
component supplied by WHALE HEAT and shall in no event be liable to BUYER OR BUYER’S customers for
any incidental or consequential damages, or loss of use, or other losses, however occasioned.
Implied warranties of merchantability and of the tness of the product for any purpose are warranted for a period
of two years on parts and labor.
WHALE HEAT makes no warranties, expressed or implied after that time.
Some states do not allow limitation on how long an implied warranty lasts or for the exclusion or limitations of
incidental or consequential damages, therefore, the above limitations may not apply to you.
This warranty is extended to the original purchaser only, unless purchased for purpose of resale. This warranty
gives you specic legal rights, and you may also have other rights which vary from state to state.
REPAIR PARTS
Repair parts listed herein may be ordered through Attwood Corporation, Attwood Distributors and Dealers, or
Dealer’s Authorized Service Centers. All parts will be shipped at prevailing prices.
When ordering repair parts, please give the following information:
1. The part number
2. The part description
3. The model number of the water heater
4. The serial number of the water heater
The model number and serial number of the water heater will be found on the rating plate located on the front
panel. For the Authorized Service Center nearest you, please contact Attwood Corporation.
Attwood Corporation
1016 North Monroe Street
Lowell, MI 49331
Tel: [phone]
[email protected]
17

NOTES
18