Wharfedale Pro Titan 12 ACTIVE User manual

www.wharfedalepro.com
2-WAY PROFESSIONAL
PASSIVE LOUDSPEAKER
TITAN 12 User’s Manual
TITAN 12_Manual RevC.indd 1 8/31/06 4:30:49 PM

USER'S MANUAL
Titan 12 is the latest innovation from
Wharfedale Pro. A high performance passive
speaker system designed around your needs.
High output, punchy low end and extended
high frequency response that’s equally at
home with music and speech. An ultra-light-
weight composite enclosure that’s designed
to be stand mounted, arrayed or even used
as a floor monitor. Compact, lightweight and
affordable, the Titan 12 still packs professional
drivers that deliver unmatched performance.
TITAN 12_Manual RevC.indd 2 8/31/06 4:30:49 PM


TITAN 12 • 2-way Passive Loudspeaker
Warnings & Safety Instructions
1. READ ALL INSTRUCTIONS carefully and become familiar with the features and
functions of this product before operating it.
2. RETAIN THESE INSTRUCTIONS for future reference.
3. COMPLY WITH ALL WARNINGS – All warnings and instructions for this product
should be adhered to.
4. USE WITH AMPLIFIERS – In order to avoid damage to drivers and other equipment,
it is advisable to establish and follow a routine for powering up and powering down a
sound system. With all system components connected, turn on source equipment (mixers,
signal processors, record and playback units, etc.) BEFORE powering up amplifiers. Tran-
sient voltages from powering up source equipment can damage speakers if amplifiers are
turned on when these sources are powered up. Make sure that amplifier volumes are set
to their minimum settings and power up any system amplifiers LAST. It is recommended
that all system components be allowed to stabilize for several seconds before any source
signals are introduced or level setting adjustments are made.
Similarly, when shutting systems down, turn all amplifiers off first, before
powering down any other system components.
5. CABLES – Do not use shielded or microphone cables for connection between
amplifiers and speakers. Use only approved speaker cables with proper
connectors.
6. RIGGING – SUSPENDING – MOUNTING – Rigging, suspending and mounting of this
speaker system can expose members of the public to serious health and risks and even
death. UNDER NO CIRCUMSTANCES ATTEMPT TO RIG, SUSPEND OR OTHERWISE MOUNT
THIS SYSTEM UNLESS YOU ARE FULLY QUALIFIED AND CERTIFIED TO DO SO BY REL-
EVANT LOCAL, STATE AND NATIONAL AUTHORITIES. ALL RELEVANT SAFETY REGULA-
TIONS MUST BE FOLLOWED. IF YOU ARE NOT PROPERLY QUALIFIED OR DO NOT KNOW OF
PERTINENT REGULATIONS, CONSULT QUALIFIED PERSONNEL FOR ADVICE.
7. CAUTION – These professional loudspeaker systems are capable of generating very
high sound pressure levels. Use care with placement and operation to avoid exposure to
excessive volume levels that can cause permanent hearing damage if operated to ex-
tremes.
8. SERVICE – There are no user serviceable parts inside this product. Users should not
attempt to service this product. Warranty nullification could result if this is attempted.
TITAN 12_Manual RevC.indd 3 8/31/06 4:30:49 PM


Thank you for purchasing the Wharfedale Pro TITAN 12!
The TITAN 12 offers acoustical voicing and drivers that provide a smooth high end re-
sponse and a punchy, tight low end bass response in a surprisingly small and portable
composite enclosure.
Features:
+Custom designed, heavy duty 12” low frequency driver
+1.75" titanium high frequency compression driver
+90 x 60 degree integral Elliptical Wave Guide for even high frequency dispersion
+Built in 18dB per octave Linkwitz-Riley crossover
+DTF™ Dynamic Thermal Filament – Integral High-Frequency Driver
Overload protection
+High frequency EQ switch (boost/flat)
+Design for a wide variety of sound reinforcement applications
+Built in, rubberized easy-grip handles for convenient transportation
+Integral pole mount adapter for stand mounting
+Trapezoidal shape for vertical arrays and horizontal stage monitor use
+Top stacking feature for easy integration of multiple enclosures
+Ten M8 threaded rigging inserts for several hang-mount options
+Bottom mounted M8 threaded inserts that fit OmniMount® 60.0 footprint
+Injection molded enclosure construction
+Integral cord wrap and cable anchor molded into the enclosure
+Dual ¼" and NL4 input connectors
TITAN 12_Manual RevC.indd 4 8/31/06 4:30:49 PM


Operation
The TITAN 12 is a passive, two-way, speaker system that provides an 8 ohm impedance
load, per enclosure, to each output channel of the system power amplifier. Multiple
TITAN 12 enclosures can be “daisy-chained”, in parallel, with the impedance load
dropping in half with each additional enclosure. In other words, two TITAN 12 enclosures,
connected in parallel, will provide a 4 Ohm impedance load. Like wise, three TITAN 12
enclosures connected in parallel will provide a 2 ohm impedance load to the amplifier. Be
aware that some amplifiers are not designed to accept loads as low as 2 ohms and loads
this low can result in decreased performance and overheating of the amplifier and can
cause damage to amplifier electronics. Consult the manufacturers operating manual for
the amplifier before connecting multiple speakers together.
The HIGH FREQUENCY EQ switch provides a 3dB boost to the high frequency driver for
long throw applications. Switch selections are “BOOST” (3dB increase) and “FLAT”
(no increase).
Connections
The TITAN 12 input connections from the output of the amplifier will be via ¼” phone
jacks or Speakon® NL4 connectors that are located on the rear mounted input plate. NL4
connector pin wiring is configured as follows:
+1 = Positive
–1 = Negative
Optional Accessories
+ Wall mount bracket – Enables surface mounting with pan and tilt positioning for
fixed installations
+ Titan Tour Bag – Ballistic nylon zippered carrying bag with storage pocket
for cables
TITAN 12_Manual RevC.indd 5 8/31/06 4:30:49 PM


TITAN 12 Specifications
Loudspeaker Type: 12" 2-way
Frequency Response (+/–3dB): 55—20kHz
Sensitivity (1W@1M): 98dB
HF Coverage (H x V): 90˚ x 60˚
Peak SPL: 128dB
System Impedance: 8 ohm
POWER HANDLING CAPABILITY (WATTS)
Continuous: 250W
Music: 500W
Peak: 1000W
LOW FREQUENCY DRIVER
Size: 305mm/12"
Coil Size:
HIGH FREQUENCY DRIVER
Type: Compression Driver
Coil Size: 44mm/1.75"
Exit Size: 25mm/1"
Diaphragm Material: Titanium
HF Driver Protection: DTF™ Dynamic Thermal Filament
HF Long-Throw EQ Compensation: 3dB boost (long-throw) / Flat (near-field)
HIGH FREQUENCY HORN
Type: EWG™ - Elliptical Waveguide
Throat Size: 25mm/1"
CROSSOVER
Type: 2-way
Frequency/Filter:
ENCLOSURE
Shape: Trapezoidal for vertical array and horizontal stage
monitor applications
Material: Polypropylene
Rigging: + (10) M8 threaded rigging points for safe flown applications
+ (4) M8 threaded rigging points on bottom in
Omnimount®6.0-type footprint
+ Speaker pole-mount receptacle with lock screw
+ Optional wall-mount bracket
+ Optional dual-unit array speaker stand hardware
IN/OUT PANEL
Input Connectors: (2) 1/4" jacks '+ (2) NL4 connectors
DIMENSIONS/WEIGHTS
Net Weight: 12kg / 26.4lbs
Gross Weight: 14kg / 30.8lbs
Dimensions (H x W x D): 556 x 384 x 312mm / 21.88" x 15.1" x 12.3"
*Features, details and specifications subject to change without notice
TITAN 12_Manual RevC.indd 6 8/31/06 4:30:49 PM
64.26mm / 2.5"
2.2KHz / Linkwitz-Riley

THE WHARFEDALE PRO ADVANTAGE
While other companies increasingly out-
source manufacturing, we continue to add
to our factory; already at 1.5 million square
feet in size. That’s because at Wharfedale
Pro we design, engineer, tool and manufac-
ture each and every component that goes into
our speaker systems. All of which helps ex-
plain how we can pack so much technology,
performance and quality into our products
at an incredibly low cost. Recognized since
1932 as a pioneering brand, Wharfedale Pro
is now part of the International Audio Group
with operations and distributionworldwide.
Our mission remains to design and build
the very best Pro Audio gear possible, with
great technologies, abundant features and
unmatched quality at the very lowest possible
cost. That’s the Wharfedale Pro advantage!
TITAN 12_Manual RevC.indd 7 8/31/06 4:30:50 PM

* Details and specifications subject to change without notice.
© 2006 Wharfedale Pro is a member of the International Audio Group .
IAG House, Sovereign Court, Ermine Business Park, Huntingdon, Cambridgeshire, PE29 6XU
WHARFEDALE PRO [USA] WHARFEDALE PRO [UK] WHARFEDALE PRO [GERMANY] WHARFEDALE PRO [INT.]
ph: +1.877.440.0888 ph: [phone] ph: [phone] ph: [phone]
ph: +1.425.861.3909 ph: [phone] fx: [phone] fx: [phone]
fx: +1.425.861.3906 fx: [phone]
UNPACKING
All Wharfedale Pro products are fully checked before leaving the factory.
After unpacking please inspect cabinets for any physical damage. Please
retain the shipping carton if possible and internal packing material in
case the unit needs to be returned. Please check as soon as possible that
the unit is functioning. In the event of any damage, please contact your
dealer immediately.
WHARFEDALE PRO LIMITED WARRANTY *
Wharfedale Titan loudspeaker systems are warranted to be clear of man-
ufacturing or materials defects for a period of one year from the original
date of purchase. In the event of malfunction, contact your authorized
Wharfedale Professional dealer or distributor for information.
* Be aware that warranty details may differ from country to country.
Contact your dealer or distributor for information. These terms do not
infringe your statutory rights.
www.wharfedalepro.com
TITAN 12_Manual RevC.indd 8 8/31/06 4:30:50 PM
INTERNATIONAL PATENT PROTECTION ZL 200530151345.9