Whirlpool 1157672 User manual

L
Part No. 1157672 Rev. D
IMPORTANT:
Read and save
these instructions.
( IMPORTANT:
Air Conditioner
j Installer: Leave Installation Instructions
with the homeowner.
Homeowner: Keep Installation Instructions
1 s for future reference.
ave Installation Instructions for local
electrical inspector’s use.

Before you
Grounded electrical outlet within
reach of the power supply cord IS
start.. .
required. See Electrical
requirements.
ProDer installation is vour
responsibility. Make sure you have
everything necessary for correct
Important: Observe all
installation. It is the customer’s
governing codes and
responsibilitv to comDlv with the
ordinances.
installation specific&i&s
provided.
7/oly\
7
opening size
Electrical outlet must
be available within
the reach of the Do Not use an
extension cord.
Check location where air An electrical outlet must be
conditioner will be installed for available within reach of the
opening size, electrical outlet, and service cord. DO NOT USEAN
airflow. EXTENSION CORD.
The opening dimensions must
have a 24-7/8” width and 15-l j4”
height.
Electrical Shock Hazard
It is the customer’s responsibility: Electrical Code, ANSI/NFPA 70-
* TO contact a qualified electri- latest edition, and all local
cc11installer. codes and ordinances.
l To assure that the electrical Failure to do so could result in
installation is adequate and in fire, electrical shock or other
conformance with National personal injury.
Personal Injury/Product Damage Hazard
l Because of the weight and size conditioner to prevent it from
of the air conditioner, more falling out of opening during
than one person is needed to installation.
move, lift and safely install it.
l Do Not locate air conditioner
l Handle air conditioner with where cabinet front is exposed
care. Metal fins on front and to a heat source that raises the
rear coils are sharp. surface temperature above
l Do Not drink the water that 120°F.
collects inside the air condi- Failure to follow these instructions
tioner. It is not sanitary.
l Maintain a firm hold on the air could result in personal injury or
damage to air conditioner.
Page 2
Tools and
materials
needed for
installation:
Order Through-the-Wall
Mounting Kit, Port No.
1158268 from authorized
parts distributor.
Electrical
requirements
Electrical Shock Hazard
l Electrical ground is required
on this appliance.
l Do Not modify the power
supply cord plug. If it does not
fit the outlet, have a proper
outlet installed by a qualified
electrician.
. Do Not have a fuse in the
neutral or grounding circuit.
A fuse in the neutral or
grounding circuit could result
in electric shock.
l Do Not use an extension cord
with this appliance.
l Check with a qualified
electrician if you are in doubt
as to whether the appliance is
properly grounded.
Failure to follow these insfructions
could result in serious injury or
death.
If codes permit and a separate
grounding wire is used, it is
recommended that a qualified
electrician determine that the
grounding path is adequate.

A single-phase, 6OHz.
AC only, electrical supFjly is
required on a separate circuit. A
15amp. time-delay fuse or circuit
breaker is required. Copper wire
(#14-gauge) is required.
The model and serial label is
located behind the front panel
on the base flange.
Specific electrical requirements
are listed in the chart. Follow the
requirements for the type of plug
on the power supply cord.
Wiring
requirements
r
Plug Type A 1 Plug Type B
J-prong
grounding
plug
I
l/4’ blade
Dower supply cord grounding prong
115volt -
230/2oa ~0tt -
103.5~ min., 197.6~ min.,
126.5~ max.
23% max.
7Samp 12-amp rating
ratings or less or less - use a
- a double single outlet
outlet is and a separate
acceptable. circuit.
7.6through
I2-amp ratings
- use only a
;ingle outlet and
;eparate circuit.
Recommended grounding
method
Do Not, under any circumstances,
remove the power supply cord
grounding prong.
For your personal safety, this
appliance must be grounded.
This appliance is equipped with a
power supply cord having a
3-prong grounding plug. To
minimize possible shock hazard.
the cord must be plugged into a
mating, 3-prong grounding-type
wall receptacle, grounded in
accordance with the National
Electrical Code, ANSI/NFPA
70-latest edition, and local codes
and ordinances. If a mating wall
receptacle is not available, it is
the personal responsibility and
obligation of the customer to
have a properly grounded,
3-prong wall receptacle installed
by a qualified electrician.
Now start...
with air conditioner in room
where it will be installed.
It is the customer’s responsibility
and obligation to have this
product installed by a qualified
technician familiar with through-
the-wall room air conditioner
installations.
Check the air conditioner model
number on the model/serial label
located behind the front panel on
the base flange.
If the air conditioner model num-
ber starts with letters ACU, it must
be installed into on air conditioner
sleeve. It will fit into a Whirlpool
sleeve, Model? AOW22W2, or a
comparable sleeve that is at least
19” deep. See THROUGH-THE-WALL
SLEEVE INSTALLATION on bock
cover.
If the air conditioner mO=del num-
ber starts with letters other than
ACU, instoll according to
THROUGH-THE-WALL INSTALLATICI\I
Appropriate
header if required
plaster t
alternate
construction
for plaster
frame
construction
Appropriate
header if required
trim*% lintel
frame
thickness
alternate
construction
or plaster e
brick veneer to ‘rame
construction
1
When using a wood, metal
n or plastic molding, the
frame should line up with the
inside wall. If the plastered wall
is to be flush with the cabinet
and no molding is used, the
frame must be set l/2-inch into
the wall.
SS
wall Dimension depends
on wall thickness
and type of molding.
2
Cut opening through the
n wall. Remove insulation.
3
Use l-inch or heavier
n lumber for wood frome.
Measure depth of wall opening
and frame. Apply wood
preservative to the outside,
exposed surface.
Page 3

4
Insert the frame in the wall
n opening, Square and level
frame. Nail frame securely to the
wall studs.
K
Remove air conditioner and
ti l front panel from carton.
Personal Injury/Product
Damage Hazard
l Maintain a firm hold on the air
conditioner to prevent it from
falling out of the opening
-during installation.
Failure to follow this instruction
could result in personal injury or
damage to the air conditioner.
air conditioner
frameT
6
Place unit in center
. of opening.
7
Place level on air
n conditioner in openinq.
There should be a tilt t6 the -
outside of about one bubble.
The air conditioner should be
level from side to side.
air conditioner
fram<.
8
Secure air conditioner in
n opening. Go to Step 9.
tab
tront panel
9
lik
screw
Remove sheet metal
n screws from front base
flange. Insert tabs on the top
edge of front panel into slots in the
air conditioner cabinet. Use two
screws to attach the bottom of
the front panel to the cabinet.
10
Use insulation to seal
n opening between
cabinet and frame. Caulk outside
wall openings around cabinet.
11
If needed, install
n moldina around
room side of cabinet.
Wall/Floor Damage
Check that air conditioner is
tilted to the outside so that
water will run to the outside.
Failure to do so may cause
damage to wall/floor coverings.
Pcirt No. 1157672 Rev. D Prepared by Whirlpool
Corporation,
t’ 1902 Whirlpool CorL>cJrcJtiorl Benton Harbor, Michigan 49022
1
Remove the rear grille from
n the air conditioner and
discard the grille. ~;--~
cabinet
flange
Place the foamseal between the
front edge of the air conditioner
base and the bottom flange of
the cabinet.
2
Install the sleeve by
n following the installation
instructions that came with it.
3
Follow THROUGH-THE-WALL
n INSTALLATION, Steps 9
through 11 to complete installa-
tion.
If your air conditioner is
not operating properly...
Check that the circuit breaker is
not tripped or house fuse blown.
Check that power supply cord is
securely plugged into the
electrical outlet.
If you need assistance...
The Whirlpool Consumer Assistance
Center will answer any questions
about operating or maintaining
your air conditioner not covered in
the Installation Instructions. The
Whirlpool Consumer Assistance
Center is open 24 hours u day, 7
days a week. Just dial (800) 253-l 301
-the call is free. When you call, you
will need the air conditioner model
number and serial number. Both
numbers are found on model and
serial label located behind the front
panel on the base flange.
Printed in U.S.A.