Whirlpool ACV09000R Installation guide
ACH09000R/ ACH12000R
Thank you for choosing our product. For proper operation, please read and
keep this manual carefully. If you have lost the User’s Manual, please
contact the customer service or visit
ᑢፕእ҈ࠨ ଐۂeྦྷכᆢ ኧАcᇼˠୀቇᚾԎѢഁړΦ說明
࣊eߗፘ使用說明࣊cᇼᐲᖎ۪ʸר৻ֶᓒᙴ以下網址.
ଐۂΪͲܞʵd使用說明及Ϊܞڲ
ʗβОࣩዀ
Model 產品型號: ACV09000R/ ACV12000R
Operation Notices
Precautions 1-6
Parts name 7-8
9
10-15
16-17
18
18
19
19-21
22-25
26
27
28
29-30
31
32-36
37-39
40
40
41
41
44
Screen Operation Guide
Buttons on remote controller
Introduction for icons on display screen
Introduction for buttons on remote controller
Function introduction for combination buttons
Operation guide
Replacement of batteries in remote controller
Emergency operation
Maintenance
Clean and maintenance
Malfunction
Malfunction analysis
Installation Notice
Installation dimension diagram
Safety precautions for installing and relocating the unit
Tools for installation
Selection of installation location
Requirements for electric connection
Installation
Installation of indoor unit
Installation of outdoor unit
Vacuum pumping
Leakage detection
Check after installation
Test operation
Pipe expanding method
Connecting the cable 45
Content
9
- Please read all instructions carefully before using this product.
- When using the appliances, should always follow this instruction to reduce the
- Please keep this manual. If you deliver the appliance to other users, do
handover this manual together.
Indicates a hazardous situation that, if not avoided, will
Indicates a hazardous situation that, if not avoided, could
Indicates a hazardous situation that, if not avoided, may
Indicates important but not hazard-related information,
used to indicate risk of property damage.
Indicates a hazard that would be assigned a signal word
WARNING or CAUTION.
Explanation of Symbols
Precautions
Operation and Maintenance
WARNING
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person
responsible for their safety.
play with the appliance (including remote control).
hazard.
Otherwise, it may cause electric shock.
persons in order to avoid a hazard.
shock or malfunction.
damage.
1
Precautions
WARNING
electric shock or damage. Please contact dealer when
you need to repair air conditioner.
remote controller may be broken.
conditioner and disconnect power immediately, and then
operation switch, please press this switch with an
plug to turn it off.
2
Precautions
WARNING
3
button when your hands are wet.
sure it is not broken.
it may cause the power cord damage and electric shock.
health. It is advisable to set the louvers in order to avoid
pressing the ON/OFF button on the remote control, and
then disconnect it from power supply.
can damage the appliance.
is to be left unused for a long period of time or during a
thunder/lightning storm.
covered by the Kyoto Protocol, the refrigerant gas being
in a hermetically sealed system. Refrigerant gas: R410a
has a Global Warming Potential (GWP) 2088.
Precautions
4
WARNING
Installation
the unit.
power supply circuit and circuit break.
separation of at least 3mm in all poles
should be
note air switch should be included magnet buckle
and heating buckle function, it can protect the circuit-
short and overload.
safety grounding. The appliance must be connected to
an electrical leakage protection switch with sufficient
capacity.
of air conditioner. Unstable power supply or incorrect
wiring or malfunction. Please install proper power supply
cables before using the air conditioner.
Precautions
WARNING
5
wire of power socket.
any work related to electricity and safety.
persons in order to avoid a hazard.
keep the interconnection cable away from the copper
tube.
national wiring regulations.
wire, which cannot be used for other purposes.
electric safety regulations.
accessible.
connected by a professional.
please contact the supplier for a new one. Avoid
extending the wire by yourself.
Precautions
WARNING
6
be installed in the line.
place, only the qualified person can perform the work.
away from animals or plants. If it is unavoidable, please
add the fence for safety purpose.
provided by the manufacturer.
NOTICE:
-18ʝ~ 43ʝ; for heat pump unit is 0ʝ~ 43ʝ
Working temperature range
ʝ ʝ)
Maximum cooling 32/23 43/26
Maximum heating 27/- 24/18
Parts Name
7
Indoor Unit
Outdoor Unit
air inlet
panel
aux.button
horizontal louver
air outlet
remote control
above graphics, please refer to actual products)
NOTICE:
Actual product may be different from above graphics, please refer to actual
products.
air inlet
air outlet
Parts Name
8
Display
products.
Green-status-ON.
Red-status-OFF.
display
temp.
indicator
receiver
window
White-W-Cool Mode-
Red-R-Heat Mode- (only for heating model)
W R G
Buttons on remote controller
Introduction for icons on display screen
1
1
2
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
3
4
5
9
10
12
14
16
6
7
8
11
13
15
ON/OFF button
FAN button
TURBO
button
button
button
SLEEP button
I FEEL button
TIMER ON / TIMER OFF button
CLOCK button
QUIET button
WiFi button
LIGHT button
button
TEMP button
Set fan speed
I feel
Quiet
Clock
Sleep mode
Light
X-FAN function
Set time
WiFi*
Turbo mode
Send signal
Healthy mode*
Scavenging functions*
8ʝheating function#
Set temperature
TIMER ON/TIMER OFF
Child lock
Auto mode
Cool mode
Fan mode
Heat mode#
Up & down swing
Left & right swing
:Set temp. :Indoor ambient temp.
:Outdoor ambient temp.
Operation mode
Temp. display type
9
# Applicable to ACH09000R /
ACH12000R only
* Applicable model only
Introduction for buttons on remote controller
10
Note:
Press this button to turn on or turn off the air conditioner. After turning on the air
FAN" button to adjust fan speed. Press " " / " "
button to adjust fan blowing angle.
When selecting cool mode, air conditioner will operate under cool mode. Cool
no heating. All indicators are off, operation indicator is ON. press "FAN" button
with multifunction; For some functions, which the model doesn't have, if press
#
When selecting heating mode#, the air conditioner operates under heat mode.
# Applicable to ACH09000R /
ACH12000R only
Introduction for buttons on remote controller
Note:
Note:
For preventing cold air, after starting up heating mode, indoor unit will delay
1~5 minutes to blow air (actual delay time is depend on indoor ambient
temperature).
Set temperature range from remote controller: 16~30ʝ(61-86ʞ);
Fan speed: auto, low speed, low-medium speed, medium speed, medium-high
speed and high speed.
is displayed and the indoor fan will continue operation for a few minutes to dry
the indoor until even though you have turned off the unit. After energization, X-FAN
OFF is defaulted. X-FAN is not available in AUTO, FAN and HEATmode. This
function indicates that moisture on evaporator of indoor unit will be blowed after
the unit is stopped to avoid mould.
button,indoor fan will continue running for a few minutes at low speed. In this
period, hold fan speed button for 2s to stop indoor fan directly.
button, the complete unit will be off directly.
Under COOL or HEATmode, press this button to turn on quick COOL or quick
If start this function, the unit will run at super-high fan speed to cool or heat quickly
so that the ambient temp. approachs the preset temp. as soon as possible.
to byʝ(ʞ).
will change quickly. Release button after setting is finished, temperature
under auto mode)
This button is used for setting Fan Speed in the sequence that goes from AUTO, ,
,, , , then back to Auto.
FAN button
TURBO button
5button
Auto
Low speed Low-Medium speed Medium speed
Medium-High speed High speed
11
Note:
Note:
"""""" for details.
Press this button continuously for more than 2s, the main unit will swing back
and forth from left to right, and then release the button, the unit will stop
swinging and present position of guide louver will be kept immediately.
Under swing left and right mode, when the status is switched from off to ,
if press this button again 2s later, will disappear directly; if press this button
again within 2s, the change of swing status will also depend on the circulation
sequence stated above.
for applicable models only
IFare not the
air conditioner will blow fan automatically.
Press this button continuously, the main unit will swing back and forth from up
to down, and then release the button, the unit will stop swinging and present
position of guide louver will be kept immediately.
Under swing up and down mode, when it is switched from off to , if press
this button again 2s later, status will disappear directly; if press this button
again within 2s, the change of swing status will also depend on the
circulation sequence stated above.
Press this button to select left & right swing angle. Fan blow angle can be
selected circularly as below:
Press this button to select up & down swing angle. Fan blow angle can be
selected circularly as below:
12
Introduction for buttons on remote controller
6
7
(
louver will automatically swing up & down at maximum angle.
for more thanthe
the required angle, release the button.
Left / Right button
Up/ Down button
13
Introduction for buttons on remote controller
Press this button, can select Sleep 1 ( ), Sleep 2 ( ), Sleep 3 ( ) and cancel
mode
Sleep 1 is Sleep mode 1, in Cool modes; sleep status after run for one hour, the
main unit setting temperature will increase 1 ʝ. After two hours, setting
temperature increased 2 ʝ, then the unit will run at this setting temperature; In
Heat mode: sleep status after run for one hour, the setting temperature will
decrease 1ʝ.After two hours, setting temperature will decrease 2ʝ, then
the unit will run at this setting temperature.
Sleep 2 is sleep mode 2, that is air conditioner will run according to the
presetting a group of sleep temperature curve.
(1)Under Sleep 3 mode, press “Turbo” button for a long time, remote controller
enters into user individuation sleep setting status, at this time, the time of remote
controller will display “1hour”, the setting temperature will display the
Default
temperature will be shown for the initial use);
Press to
(3) At this time, 1hour will be automatically increased at the timer position on the
curve and blink;
(4) Repeat the above step (2)~(3) operation, until 8 hours temperature setting
finished, sleep,curve setting finished, at this time, the remote controller will
resume tooriginal timer display; temperature display will resume to original
setting temperature.
The
user could accord to sleep curve setting method to inquire the presetting sleep
curve, enter into user individuation sleep setting status, but do not change
presetting or enquiry procedure, if no button is pressed within 10s, the sleep
curve setting status will be automatically quit and resume to the original
will quit
similarly.
controller. When this function is set, the remote controller will send the detected
indoor temperature according to the detected temperature. Press this button again
turn off
8SLEEP button
9I FEEL button
14
Introduction for buttons on remote controller
to avoid detecting inaccurate ambient temperature.
TIMER ON button
For on
later, the time will change quickly until reaching your required time.
resumes displaying. Cancel TIMER ON: Under the condition that TIMER ON is
TIMER OFF button
For on
later, the time will change quickly until reaching your required time.
Cancel TIMER OFF. Under the condition that TIMER OFF is started up, press
Under on or off status, you can set TIMER OFF or TIMER ON simultaneously.
Z#*>`'#*>`'QQ!
After starting up TIMER ON or TIMER OFF, set the constant circulating valid.
After that, air conditioner will be turned on or turned off according to setting time.
ON/OFF button has no effect on setting. If this function is not needed, please use
remote controller to cancel it.
Clock time adopts 24-hour mode.
The interval between two operation can't exceeds 5s. Otherwise, remote controller
will quit setting status. Operation for TIMER ON/TIMER OFF is the same.
TIMER ON / TIMER OFF button
Note:
For e
time will change quickly. Release thebutton when reaching your required time.
Note:
CLOCK button
15
())*)+**&%*&,*&%%&&*.%),%%+%*&%)%
),%%+%*&%
+**&%
+**&%
+**&%
())*)+**&%*+*)**+))+%(*+*&+*$&)'.%
)%%+*$&)'.)%%+**()%&
)%&)'.*('&(&%*+*)+*
+*+%*&%%)*+'%$&)%(*+*$&
*%
)')%&*,
())+**&%*&*+(%&%&(*+(%&+%*&%%+%*&%)
*+(%&%*&%)'.&%($&*&%*(&(%()**+)
&($&*&%*(&(&'())%+**&%))$+*%&+).&()
$&+()*&(*&*&(.+*)**%
signal
MODE
Under cooling mode: indoor fan operates at notch 4 speed. 10 minutes later or
when indoor ambient temperature≦28oC, indoor fan will operate at notch 2
speed or quiet mode according to the comparison between indoor ambinet
temperature and set temperature.
Under heating mode: indoor fan operates at notch 3 speed or quiet mode
according to the comparison between indoor ambinet temperature and set
temperature.
Under dry and fan mode: indoor fan operates at quiet mode.
Under auto mode: the indoor fan operates at the auto quiet mode according to
actual cooling, heating or fan mode.
for applicable models only
utton
Press this button to turn off the display light on indoor unit. " " icon on remote
controller disappears. Press this button again to turn on display light. " " icon
is displayed.
#$(%!.
')"%')*'#)$'
$##$$'*#)(%!.(())"%')*'
')"%')*'#)$'$##$$'*#)
(%!.(#$$'"#))"%')*'
')"%')*'#)$'$##$$'*#)
(%!.($*)$$'"#))"%')*'
*)$$')"%')*'(%!.(#$)+!!$'($""$!())))"#$$'
*#)'+((#!,!)(%!.(#$$'())"%')*'
(*!))$(%!.())"%')*',#)*'##$#)*#)'(#$
(%!.#)'"$)$#)'$!!'
.
$*)$$'"#))"%')*'#$$'
)"%')*'#)$'(%!.($''(%$##)"%')*'#*)$")!!.)*'#
16
(%l.('(()*))o#o')(o#)me to start healthy and
scavenging functions simultaneously; LCD displays " " and " ". Press this
button for the third time to quit healthy and scavenging functions simultaneously.
Press the button for the fourth time to start healthy function; LCD display " ".
6TEMP button
By pressing this button, you can see indoor set temperature, indoor ambient temp-
erature or outdoor ambient temperature on indoor unit's display. The setting on
remote controller is selected circularly as below :
for applicable models only
17
ć
ʝDQGʞ
#'$$!#"$%'((#*))$#(("*!)#$*(!.)$
()')*%$')*'#$#'.(+#*#)$###'.(+#*#)$#(()')
*%,!!($,#$#'"$)$#)'$!!'#'$#)$#',!! *())()
)"%')*'*)$")!!.$'#)$-)$'.())#)$')$)()
#'.(+#)'((#*))$#(("*!)#$*(!.#)$
-)#'.(+#*#)$#
*()
This manual suits for next models
3
Table of contents
Other Whirlpool Air Conditioner manuals
Whirlpool
Whirlpool 1188908 Assembly instructions
Whirlpool
Whirlpool ACS102PP User manual
Whirlpool
Whirlpool 63851341 Assembly instructions
Whirlpool
Whirlpool ACS082PP0 User manual
Whirlpool
Whirlpool ACE244PT1 User manual
Whirlpool
Whirlpool AMD 302 User manual
Whirlpool
Whirlpool 881406658997 Assembly instructions
Whirlpool
Whirlpool 1172397 User manual
Whirlpool
Whirlpool AMD 064 User manual
Whirlpool
Whirlpool AR1000 User manual
Whirlpool
Whirlpool WHAW061BW User manual
Whirlpool
Whirlpool AMAP101AB User manual
Whirlpool
Whirlpool 1188907 Assembly instructions
Whirlpool
Whirlpool RH123A1 User manual
Whirlpool
Whirlpool BHAC1400XS0 User manual
Whirlpool
Whirlpool ACP102PS2 User manual
Whirlpool
Whirlpool CA25WC50 Operation manual
Whirlpool
Whirlpool AMD 091/1 User manual
Whirlpool
Whirlpool AMD 084 User manual
Whirlpool
Whirlpool ACU072XE Product information sheet
Popular Air Conditioner manuals by other brands
Fujitsu
Fujitsu ASYG 09 LLCA installation manual
York
York HVHC 07-12DS Installation & owner's manual
Carrier
Carrier Fan Coil 42B Installation, operation and maintenance manual
intensity
intensity IDUFCI60KC-3 installation manual
Frigidaire
Frigidaire FAC064K7A2 Factory parts catalog
Sanyo
Sanyo KS2432 instruction manual
Mitsubishi Electric
Mitsubishi Electric PUHZ-RP50VHA4 Service manual
Panasonic
Panasonic CS-S18HKQ Service manual
Panasonic
Panasonic CS-E15NKE3 operating instructions
Gree
Gree GWH18TC-K3DNA1B/I Service manual
Friedrich
Friedrich ZoneAire Compact P08SA owner's manual
Daikin
Daikin R32 Split Series installation manual