Whirlpool PACHW2900CO User manual

Instructions for use

-3-
PACHW2900CO
ENGLISH Instructions for use Page 4

-4-
SAFETY INSTRUCTIONS
IMPORTANT TO BE READ AND OBSERVED
• Download the complete instruction manual on docs.whirlpool.eu or call the phone
number shown on the warranty booklet.
• Before using the appliance, read these safety instructions. Keep them nearby for future
reference.
• These instructions and the appliance itself provide important safety warnings, to be
observed at all times. The manufacturer declines any liability for failure to observe
these safety instructions, for inappropriate use of the appliance or incorrect setting of
controls.
• The appliance uses flammable refrigerant (R290),the maximum refrigerant charged
amount is 0.22 kg.The appliance shall be installed,operated and stored in a room with a
floor area larger than 11 m2. And the room should higher than 2.2 m.
The appliance was tested within 0.95 MPa - 1.05 MPa of external static pressures.
• Very young children (0-3 years) should be kept away from the appliance. Young
children (3-8 years) should be kept away from the appliance unless continuously
supervised. Children from 8 years old and above and persons with reduced physical,
sensory or mental capabilities or lack of experience and knowledge can use this
appliance only if they are supervised or have been given instructions on safe use and
understand the hazards involved. Children must not play with the appliance. Cleaning
and user maintenance must not be carried out by children without supervision.
PERMITTED USE
• CAUTION: the appliance is not intended to be operated by means of an external
switching device, such as a timer, or separate remote controlled system.
• This appliance is intended to be used in household and similar applications such as:
hotels and working offices.
• This appliance is not for professional use.
• Always turn off the air conditioner by remote control or power button on product
panel first.
Do not use the power supply circuit breaker or pull off the plug to turn it off.
Disconnect the air conditioner from the power supply if it is to be left unused for a long
period of time or during a hunder/lightning storm.
Never insert obstacle in the air outlet-risk of injury. Keep ventilation openings clear
of any obstruction.

-5-
SAFETYINSTRUCTIONS
INSTALLATION
• The appliance must be handled and installed by two or more persons - risk of injury.
Use protective gloves to unpack and install - risk of cuts.
• Installation, including electrical connections, and repairs must be carried out by a
qualified technician according to national wiring rules.
Do not repair or replace any part of the appliance unless specifically stated in the user
manual.
Keep children away from the installation site. After unpacking the appliance, make sure
that it has not been damaged during transport.
In the event of problems, contact the dealer or your nearest After-sales Service.
Once installed, packaging waste (plastic, styrofoam parts etc.) must be stored out of
reach of children - risk of suffocation.
The appliance must be disconnected from all remote power supply before any
installation operation - risk of electric shock.
During installation, make sure the appliance does not damage the power cable - risk
of fire or electric shock. Only activate the appliance when the installation has been
completed.
The flexible exhaust hose allows placement of the air conditioner between 23”and
67”(60 cm and 170 cm) from window or door.
• Do not operate your air conditioner in a wet room such as a bathroom or laundry room.
• Disconnect power cord before moving the appliance.

-6-
SAFETY INSTRUCTIONS
ELECTRICAL WARNINGS
• The power supply must be of rated voltage with special circuitry for the appliance.
The diameter of the power cord must comply with requirements.
• It must be possible to disconnect the appliance from the power supply by unplugging.
The appliance must be earthed in conformity with national electrical safety standards.
• The use of a time-delay fuse or time-delay circuit breaker is recommended. All
wiring must comply with local and national electrical regulations and be installed by a
qualified electrician.
• Do not use extension leads, multiple sockets or adapters. The electrical components
must not be accessible to the user after installation. Do not use the appliance when you
are wet or barefoot. Do not operate this appliance if it has a damaged power cable or
plug, if it is not working properly, or if it has been damaged or dropped.
• If the supply cord is damaged, it must be replaced with an identical one by the
manufacturer, its service agent or similarly qualified persons in order to avoid a hazard-
risk of electrical shock.
• Ensure safe grounding and a grounding wire connected with the special grounding
system of the building, installed by professionals. The appliance must be fitted with
electrical leakage protection switch and an auxiliary circuit breaker with sufficient
capacity. The circuit breaker must also have a magnetic and a thermal tripping function
to ensure protection in case of short-circuit and overload.
• The appliance shall be installed in accordance with national wiring regulations.
Model 9K
Required capacity of circuit breaker 16A (Fuse Type: T3.15A/250VAC)
CLEANING AND MAINTENANCE
• WARNING: Ensure that the appliance is switched off and disconnected from the
power supply before performing any maintenance operation; never use steam cleaning
equipment - risk of electric shock.
DISPOSAL OF PACKAGING MATERIALS
• The packaging material is 100% recyclable and is marked with the recycle symbol . The various parts of the packaging must
therefore be disposed of responsibly and in full compliance with local authority regulations governing waste disposal.
DISPOSAL OF HOUSEHOLD APPLIANCES
• This appliance is manufactured with recyclable or reusable materials. Dispose of it in accordance with local waste disposal
regulations. For further information on the treatment, recovery and recycling of household electrical appliances, contact your
local authority, the collection service for household waste or the store where you purchased the appliance. This appliance is
marked in compliance with European Directive 2012/19/EU, Waste Electrical and Electronic Equipment (WEEE). By ensuring this
product is disposed of correctly, you will help prevent negative consequences for the environment and human health.
The symbol on the product or on the accompanying documentation indicates that it should not be treated as domestic
waste but must be taken to an appropriate collection center for the recycling of electrical and electronic equipment.
DECLARATION OF CONFORMITY
• This product contains Fluorinated Greenhouse Gases covered by the Kyoto Protocol, the refrigerant gas being in a hermetically
sealed system (R290, GWP 3 ).Please refer to the rating label for detailed information.

-7-
SAFETYINSTRUCTIONS
Explanation of symbols displayed unit.
WARNING
This symbol shows that this appliance uses a flammable
refrigerant.
If the refrigerant is leaked and exposed to an external ignition
source, there is a risk of fire
CAUTION This symbol shows that the operation manual should be read
carefully
CAUTION This symbol shows that a service personnel should be handling
this equipment with reference to the installation manual
CAUTION This symbol shows that information is available such as the
operating manual or installation manual
SAFETY INSTRUCTIONS FOR SERVICING APPLIANCE WITH SPESIFIC REFRIGERANT
• Download the complete manual for detailed installation, servicing, maintenance and
reparing methods on docs.whirlpool.eu.
• Do not use means to accelerate the defrosting process or to clean, other than those
recommended by the manufacturer.
• The appliance shall be stored in a well-ventilated area where the room size
corresponds to the room area as specified for operation; without continuously
operating ignition sources (such as; open flames, an operating gas appliance or an
operating electric heater).
• Do not pierce or burn. Be aware that the refrigerants may not contain an odor.
Any person who is involved with working on or breaking into a refrigerant circuit
should hold a current valid certificate from an industry-accredited assessment
authority, which authorizes their competence to handle refrigerants safely in
accordance with an industry recognized assessment specification. Servicing shall only
be performed as recommended by the equipment manufacturer. Maintenance and
repair requiring the assisstance of other skilled personnel shall be carried out under the
supervision of the person competent in the use of flammable refrigerants. Appliance
shall be installed, operated and stored in a room with a floor area larger than 11 m2. The
installation of pipe-work shall be kept to a room with a floor area larger than 11 m2. The
pipe-work shall be compliance with national gas regulations. The maximum refrigerant
charge amount is 0.22 kg.
When flared joints are reused , the flare part shall be re fabricated.
1. Transport of equipment containing flammable refrigerants shall be compliant with the
transport regulations.
2. Marking of equipment using signs shall be compliant with local regulations.
3. Disposal of equipment using flammable refrigerants shall be compliant with national
regulations.

-8-
SAFETY INSTRUCTIONS
4. The storage of equipment / appliances should be in accordance with the
manufacturer’s instructions.
5. Storage of packed (unsold) equipment Storage package protection should be
constructed such that mechanical damage to the equipment inside the package
will not cause a leak of the refrigerant charge. The maximum number of pieces of
equipment permitted to be stored together will be by local regulations.
6. Information on servicing.
6-1 Checks to the area
Prior to beginning work on system containing flammable refrigerants, safety checks are
necessary to ensure that the risk of ignition is minimized. For repair to the refrigerating
system the following precautions shall be complied with prior to conducting work on
the system.
6-2 Work procedure
Work shall be undertaken under a controlled procedure so as to minimize the risk of
flammable gas or vapour being present while the work is being performed.
6-3 General work area
All maintenance staff and others working in the local area shall be instructed on the
nature of work being carried out. Work in confied spaces shall be avoided.
6-4 Checking for presence of refrigerant
The area shall be checked with an appropriate refrigerant detector prior to and during
work, to ensure the technician is aware of prtentially flammable atmospheres. Ensure
that hte leak detection equipment being used is suitable for use with flammable
refrigerants, i.e. non-sparking adequately sealed or intrinsically safe.
6-5 Presence of fire extinguisher
If any hot work is to be conducted on the refrigerating equipment or any associated
partsappropriate fire extinguishing equipment shall be avalaible to hand. Have a dry
powder or CO2 fire extinguisher adjacent to the charging area.
6-6 No ignition sources
No person carrying out work in relation to a refrigerating system which involves exposing
any pipe work that contains or has contained flammable refrigerant shall use any
sources of ignition in such a manner that it may lead to the risk of fire or explosion.
All possible ignition sources, including cigarette smoking, should be kept sufficiently
far away from the site of installation, repairing, removing and disposal, during which
flammable refrigerant can possibly be released to the surrounding space. Prior to work
taking place, the area around the equipment is to be surveyed to make sure that there
are no flammable hazards or ignition risks.“No Smoking”signs shall be displayed.
6-7 Ventilated area
Ensure that the area is in the open or that it is adequately ventilated before breaking into
the system or conducting any hot work. A degree of ventilation shall continue during
the period that the work is carried out. The ventilation should safely disperse any
released refrigerant and preferably expel it externally into the atmosphere.

-9-
SAFETYINSTRUCTIONS
6-8 Checks to the refrigerating equipment
Where electrical components are being changed, they shall be fit for the purpose
and to the correct specification. At all times the manufacturer’s maintenance and
service guidelines shall be followed. If in doubt consult the manufacturer’s technical
department for assistance. The following checks shall be applied to installations using
flammable refrigerants:
- The actual refrigerant charge is in accordance with the room size within which the
refrigerant containing parts are installed;
- The ventilation machinery and outlets are operating adequately and are not obstructed;
- If an indirect refrigerating circuit is being used, the secondary circuit shall be checked
for the presence of refrigerant;
- Marking to the equipment continues to be visible and legible. Markings and signs that
are illegible shall be corrected;
- Refrigerating pipe or components are installed in a position where they are unlikely to
be exposed to any substance which may corrode refrigerant containing components,
unless the components are constructed of materials which are inherently resistant to
being corroded or are suitably protected against being so corroded.
6-9 Checks to electrical devices
Repair and maintenance to electrical components shall include initial safety checks and
component inspection procedures. If a fault exists that could compromise safety, then
no electrical supply shall be connected to the circuit until it is satisfactory dealt with. if
the fault cannot be corrected immediately but it is necessary to continue operation, an
adequate temporary solution shall be used. This shall be reported to the owner of the
equipment so all parts are advised. Initial safety checks shall include:
- That capacitors are discharged: this shall be done in a safe manner to avoid possibility
of sparking;
- That there no live electrical components and wiring are exposed while charging,
recovering or purging the system;
- That there is continuity of earth bonding.
7. Repairs to sealed components
During repairs to sealed components, all electrical supplies shall be disconnected from
the equipment being worked upon prior to any removal of sealed electrical supply to
equipment during servicing, then a permanently operating form of leak detection shall be
located at the most critical point to warn of a potentially hazardous situation. Particular
attention shall be paid to the following to ensure that by working on coelectrical
components. The casing is not altered in such a way that the level of protection is
affected. This shall include damage to cables, excessive number of connections, terminals
not made to original specification, damage to seals, incorrect fitting of glands, etc.
Ensure that apparatus is mounted securely. Ensure that seals or sealing materials
have not degraded such that they no longer serve the purpose of preventing the
ingress of flammable atmospheres. Replacement parts shall be in accordance with the
manufacturer’s specifications.
NOTE:
The use of silicon sealant may inhibit the effectiveness of some types of leak detection
equipment. Intrinsically safe components do not have to be isolated prior to working on them.

-10-
SAFETY INSTRUCTIONS
8. Repair to intrinsically safe components
Do not apply any permanent inductive or capacitance loads to the circuit without ensuring
that this will not exceed the permissible voltage and current permitted for the equipment
in use. Intrinsically safe components are the only types that can be worked on whilelive in
the presence of a flammable atmosphere. The test apparatus shall be at the correct rating.
Replace components onlywith parts specified by the manufacturer. Other parts may result
in the ignition of refrigerant atmosphere from a leak.
9. Cabling
Check that cabling will not be subject to wear, corrosion, excessive pressure, vibration, sharp
edges or any other adverse environmental effects.The check shall also take into account the
effects of aging or continual vibration from sources such as compressors or fans.
10. Detection of flammable refrigerants
Under no circumstances shall potential sources of ignition be used in the searching for or
detection of refrigerant leaks. A halide torch (or any other detector using a naked flame)
shall not be used.
10. Leak detection methods
The following leak detection methods are deemed acceptable for systems containing
flammable refrigerants:
- Electronic leak detectors shall be used to detect flammable refrigerants, but the
sensitivity may not be adequate, or may need re-calibration (Detection equipment shall
be calibrated in a refrigerant-free area.)
- Ensure that the detector is not a potential source of ignition and is suitable for the
refrigerant used.
- Leak detection equipment shall be set at a percentage of the LFL of the refrigerant and
shall be calibrated to the refrigerant employed and the appropriate percentage of gas
(25% maximum) is confirmed.
- Leak detection fluids are also suitable for use with most refrigerants but the use of
detergents containing chlorine shall be avoided as the chlorine may react with the
refrigerant and corrode the copper pipe-work.
- If a leak is suspected, all naked flames shall be removed/ extinguished.
- If a leakage of refrigerant is found which requires brazing, all of the refrigerant shall
be recovered from the system, or isolated (by means of shut off valves) in a part of the
system remote from the leak.
11. Removal and evacuation
- When breaking into the refrigerant circuit to make repairs - or for any other purpose
conventional procedures shall be used. However, it is important that best practice is
followed since flammability is a consideration.
The following procedure shall be adhered to:
- Remove refrigerant;
- Purge the circuit with inert gas;
- Evacuate;
- Purge with inert gas;
- Open the circuit by cutting or brazing.
The refrigerant charge shall be recovered into the correct recovery cylinders.The system
shall be purged with OFN to render the appliance safe for flammable refrigerants. This