Whirlpool LA6500XP User manual

g
&&J?L’ SERIES
AUTOMATIC
WASHER
Design 2000”
k;lz,Capacity
LA6500XP
wave Ovens, Trash Compactors, Room Air Condltmners. Oehumldlhers, Automatic Washers, Clothes Dryers. free2erS. Retrlgerator-Free21

Parts and features
LAUNDRY TEMPERATURE
LIQUID BLEACH
DISPENSER
LIQUID FABRIC
-SOFTENER DISPENSER
1 MODEL AND SERIAL NUMBER PLATE
(not shown)
’ AGITATOR
Remove the Consumer
Buy Guide label. It will be
easier to remove before
the washer is used.
You should wipe out the
basket with a damp cloth
before using to remove
dust from storing or
shipping.
Copy your Model and Serial Numbers here
When youneed service or call with a
question, have this information ready: Model Number
1. Complete Model and Serial Num-
bers(from plate underthe lid nearthe
hinge). Serio, Number
2. Purchase date from sales slio.
Copy this information in these spaces. Purchase Da+e
Keep this book in the Laundry Informa-
tion Center with your “Laundry Guide,”
sales slip and warranty. Service Company/
Phone Number
There is no warranty registration to return. Proof-of-purchase is all
that is required for in-warranty service.
2

Your re!sponsibilities
Read this “Use and Care Guide”
and your “Laundry Guide” care-
fully for important use and safety
information.
You are personally responsible
for making sure that your
washer...
l is installed by a qualifiedinstaller.
l is properly installed and
leveled on a floor that can
support the weight.*
l is connected to the right kind
of outlet, electric supply, water
supply and drain.*
l is properly grounded.*
l is used only for jobs normally
expected of home automatic
washers.
l is properly maintained.
l is protected from the weather
and kept where the tempera-
ture will not fall below freezing.
l is not run by children or anyone
unable to operate it properly.
*See the “Installation Instructions”
for complete information.
Contents
Paae
PARTS AND FEATURES,
YOUR RESPONSIBILITIES.
SAFETY FIRST
STARTING YOUR WASHER
WHAT HAPPENS
IN EACH CYCLE.
OTHER OPERATING
INSTRUCTIONS
For a Rinse and Spin
For a Drain and Spin
ForaSoak . .
Liquid Bleach Dispenser
Liquid Fabric Softener
Dispenser
Cleaning the Lint Filter
CARING FOR YOUR WASHER
Winterizing
IF YOU NEED SERVICE OR
-2
3
3
4
6
10
10
10
10
11
11
ii
12
13
ASSISTANCE. 14
01985 Whirlpool Corporation
-SAVE THESE INSTRUCTIONS -

Starting your washer
Before starting your washer: 1 Measure and add detergent
2 Place sorted load in washer.
3 Start washer.
Select a
1. LOAD SIZE Select WATER 2. TEMPERATURES
l Turn the knob to point at a setting
l Match the wash water temperature
that describes the size of load you to the type of fabrics and soils being
want to wash. washed
l Set the knob on or between EX
SMALL (a few items) and LARGE
(a full load).
Recommended wash temperatures
can be found in your “Laundrv Guide”
NOTE: Use fhe LARGE wafer level
for best permanent press results.
LOAD SIZES AND WATER LEVELS
For best cleaning results, the
load must be able to move freely
in the water. loo big a load or too
little water can cause wear or
tearing of load items.
CAUTtON :
DO NOT
OVERLOAD WASHER.
*Approximate
fill with load.
LARGE (17.3 gals./655 L)’
MED (13.4 gals.:50.8 L)*
EX SMALL (9.5 gals. 136.0 L)’
4

3. Start the washer
A. Push in the Control Knob and
turn it to the right. It must be
pushed in and turned only
clockwise.
B. Stop on a number in the cycle
you want. The numbers are min-
utes of wash time. The drawing
shows10 minutes of agitation in
the REGULAR Cycle.
C. Start the washer by pulling out
the Control Knob. The washer
will fill to the level you set with
wash water of the selected
temperature. Afier filling, the
washer will agitate for the
selected number of minutes.
D. To stop the washer at any time
push in the Control Knob. To
restart the washer, pull out the
Control Knob.
5

What happens in each cycle*
Each cycle has different agitation and spin speeds designed for different
kinds of fabrics. Numbers on the dial in each cycle ore the minutes of WASH
agitation time.
When the Cycle Control Knob is set to a number and pulled out, the washer
fills before agitation and timing starts. After agitation starts, the knob turns clock-
wise until it points to OFF and the cycle ends.
REGULAR HEAVY Cycle
A cycle for sturdily con-
structed fabrics that ore
heavilv soiled.
REGULAR Cycle
/0” 10
’ I
.
regular 2.
Ea
6.
regular 10 - f-
hea”” 14 -
\
A cycle for regular loads of
fabncs that ore moderately
soiled
PERMANENT PRESS Cycle
A special cycle with the
necessary cool down rinse
which helps keep wrinkles
from setting into Permanent
Press and some synthetic
fabrics.
6

NOTE: You may hear the sound of water spraying during the spin ports of
some cycles. In some cycles, cold water is sprayed on the spinning load to help
with the rinsing
WASH
rl
NOTE: Always use cold rinse water for
High permanent press fabrics.
Speed

KNITS/GENTLE Cycle
A cycle for lightly soiled
items that need a short
wash and spin time. Wash
nylon hose in a net laundry
bag.
SOAK Cycle Brief periods of agitation
and soak time help remove
heavy soils and certain
stains that need extra
pretreatment. Use recom-
mended amount of
detergent
The SOAK Cycle
should always be fol-
lowed by a Wash Cycle.
DO NOT LOAD
ABOVE CLOTHES GUARD
B

SO;K , p;H 1,
1
Minutes
No
I)1
Minutes
Agitation 7 I sHiah peed 1’
1
WASH
6
Minutes
Hiah
7
11 ..--..
Cycle
I
Special core is needed when soaking or pre-washing laundry
See your “Laundry Guide” for proper use of this cycle. II
CAUTION :
Overloadlng or packing can...
0 cause poor cleaning;
l Increase wrlnkllng;
0 cause excessive lint;
0 wear out or tear Items.

Other operating instructions
For a rinse and spin
You may need an extra. rinse and
spin for heavily soiled loads which
need more detergent. (Extra de-
tergent can require an extra rinse.]
l Push Control Knob in.
l Turn clockwise to any l on the dial
See above drawing.
l Pull Control Knob out.
l The washer will fill to selected
level; agitate 2 minutes, drain
and spin.
For a drain and spin
Your washer can be set to drain
and spin out water.
l Push Control Knob in.
l Turn clockwise to the bar just before
OFF in any cycle. See above
drawing.
l Pull Control Knob out.
l The washer will drain and spin.
For agitation and spin speeds in each cycle, see pages 6-9.
For a soak
For best results, use warm water
for soaking stained laundry. Hot
water can set stains.
l Use recommended amount of
detergent or pre-soak product.
l Push Control Knob in
l Turn clockwise to point at a number
in the SOAK Cycle...use the 6-minute
mark for a pre-wash.*
l Pull Control Knob out to start washer.
l When the cycle is over, add de-
tergent for the next selected wash
cycle. The SOAK Cycle should
always be followed by a Wash
Cycle.
Important: See additional care
information on page 7 of your
“Laundrv Guide!’
l Set the washer and start the next
selected wash cycle.
*To start soak with agitation, the Cycle Control Knob must point to a number in
the SOAK Cycle, as indicated by the arrows.
10

Liquid bleach dispenser
Always measure bleach. Do not
guess. Never use more than 1 cup
(250 ml) for a full load. Use less with
lower water level settings. Follow
directions on bottle for safe use. Use
a cup with a pounng spout to avoid
spilling.
1. toad the washer first
2. Pour measured bleach carefully
Into dispenser DO NOT let bleach
splash, drip or run down into the
washer basket. Undiluted bleach
will damage any fabric it touches
3. Start the washer Bleach WIII be
diluted automatically during the
wash part of the cycle
For more information on bleaching, see “Laundry Guide” page 11
Liquid fabric softener dispenser
1. Add detergent and load to the
basket.
2. Add liquid fabric softener to
the dispenser using the amount
recommended on the bottle.
3. Avoid dripping or spilling any fab-
ric softener on the load.
Cleaning the lint filter
Clean filter after every load for best
filtering results. Note: The load type
will vary the amount of lint build-up.
To clean:
l Lift off the agitator barrel.
l \Nash or wipe the filter clean in the
bottom of the agitator barrel. The
filter is not removable.
l Replace the agitator barrel and
snap into place
4. Dilute fabric softener with hot
water. Add enough hot water to fill
the dispenser up to the opening.
5. Startthe washer. Diluted liquid fab-
ric softener will be added to the
load during the deep rinse portion
of the cycle.
NOTE: Do not stop the washer
during this time. If you do, the
softener will mix with the remaining
soapy wash water. This will cause
stains. Do not put detergent in the
liquid fabric softener dispenser.
6. If dispenser needs cleaning, fluih
with hot water. NOTE: Do not wash
clothes with dispenser removed.

Caring for your washer
OF
WHEN NOT WASHING, keep both
water faucets turned off. This takes
the pressure off the water inlet valve
and hoses.
APTER WASHING, use a soft dry cloth
to wipe the outside and inside dry.
Leave the lid up until the basket is dry.
Wipe up spills right away. Spills can
dull or damage the finish.
REMOM SHARP OBJECTS such as pins,
buckles, etc., from clothes before
washing. Close metal zippers.
SHARP OR HEAVY OBJECTS should
never be put on or in the washer.
Check pockets for bolts, nuts,
tools. etc.
SOME PRETREATMENT PRODUCTS
can damage washer and dryer dials,
consoles and finishes. Do not use
these products on or near your
washer or dryer.
12

Winterizing
Because some water stays in the washer, freez-
ing can cause a lot of damage. If your washer is
stored or moved during the cold weather..
1. Shut off both water
faucets. Discon-
nect and drain
water inlet hoses.
2. Put a auart of
automobile-type
antifreeze in the
basket.
3. Set the washer for a
DRAIN and SPIN
[see page 10). Let it
run for about 30
seconds to mix the
antifreeze and
water.
ON
To use the washer again.. .
-.
4. Run the washer
through a com-
plete cycle with
one cup of deter-
1. Flush water pipes and hoses. gent to clean out
2. Connect hoses to the washer. the antifreeze.
3. Turn on the water faucets.
13

If you need service or assistance, we suggest
you follow these four steps:
I Before calling for
assistance...
Performance problems often result
from little things you can find and fix
yourself without tools of any kind.
If your washer does not fill:
l Is the power supply cord plugged
into a live circuit with the proper
voltage?
l Have you checked your home’s
main fuses or circuit breaker box?
l Are the water supply hoses kinked?
l Is the Cycle Control Knob set and
pulled out?
If your washer does not spin:
l Is the lid closed?
l Is the power supply cord plugged
into a live circuit with the proper
voltage?
l Have you checked your home’s
main fuses or circuit breaker box?
If your washer stops during a cycle:
l Remember, the washer pauses
briefly at different times in each cy-
cle. These pauses are normal.
If your washer fills and drains with-
out running:
l Make sure that the Cycle Control
Knob is pointing to a number in the
cycle.
Make sure the drain hose is higher
than the water level in the washer. If
it isn’t...
l The washer may seem to be drain-
ing during wash and rinse cycles.
l Water can siphon out. (See “lnstalla-
tion Instructions!‘)
l Are both water faucets open?
14

2. If you need
as&stance*...
Call Whirlpool COOL-LINER serv-
ice assistance telephone number.
Dial free from:
Continental U.S. . [phone]
Michigan . . . . . . . . [phone]
Alaska & Hawaii [phone]
and talk with one ot our trained Con-
sultants. The Consultant can instruct
you in how to obtain satisfactory oper-
ation from your appliance or, if serv-
ice is necessary, recommend a
qualified service company in your
area.
3. If you need service*...
,z@
d
Whirlpool has
0l a nationwide
inetwork of fran-
I v
Ichised TECH-CARE R
) TfCU-CARf Service Compa-
d!~CHrSEDsERV’C~ 1nies. TECH-CARE
servile technicians are trained to
fulfill the product warranty and pro-
vide after-warranty service, any-
where in the United States. To locate
TECH-CARE service in your area, call
our COOL-LINE service assistance
telephone number(see Step 2) or look
in your telephone directory Yellow
Pages under:
4. If you have a
problem*. ..
Call our COOL-LINE service as-
sistance telephone number (see Step
2) and talk with one of our Consultants,
or if you prefer, write to:
Mr. Stephen E.Upton
Senior Vice President
Whirlpool Corporation
Administrative Center
2000 US-33, North
Benton Harbor, Ml 49022
*If you must call or write, please pro-
vide: model number, serial number,
date of purchase, and a complete
description of the problem. This infor-
mation is needed in orderto better re-
spond to your request for assistance.
FSP is a registered trademark
0
of Whirlpool Corporation for
quality parts. Look for this
FSP
symbol of quality whenever
you need a replacement part
R for your Whirlpool appliance.
FSP replacement part5
will tit right and work right, because they are
made to the same exacting specifications
used lo build every new Whirlpool appliance.

Making your world a little easier
Part NO. 308777
~11985 Whirlpool Corporation Printed in U.S.A.