Whirlpool LSP680GR User manual

SERVICE MANUAL Automatic Washer LSP680GR
(Philippines)
SPECIFICATION
Power source
Overall dimension(Net dimension)
Net weight
Power consumption
Motor output
Marked capacity of washing/spinning
Washing method
Water capacity
Water consumption
Pulsator speed
Spinner tub speed
AC 220V, 60Hz
500(W) × 535(D) × 895(H)
27kg
300W
150W
6.8kg
Automatic reverse turn
45 Liters
106 Liters (Regular wash cycle
Water level: High)
170 rpm(DELICATE 60 rpm)
850 rpm
Specification: Subject to change without notice.

2
ABNORMAL CONDITION
When the washer is abnormal, the washer stops as the every actions turns off, beep tone
sounds ON-0.1 second and OFF-0.1 second for 6 seconds and number window LED display
abnormal code. The washer judges the following six conditions as abnormal condition.
1) Abnormal condition of water supply
In supplying with water, the water level does not reach extra low level within 10 minutes or
does not reach your chosen water level within 20 minutes.
The number window LED display abnormal code: and the electric buzzer sounds to
indicate a problem at the same time.
2) Abnormal condition of drain
In draining, the water level does not go down below the reset level of the water level sensor
within 8 minutes.
The number window LED display abnormal code: and the electric buzzer sounds to
indicate a problem at the same time.
3) Abnormal condition of spin-dry
• The safety switch works 3 times continuously during the program of rinse-spin or works 1
time in the single program of spin-dry.
The number window LED display abnormal code: and the electric buzzer sounds to
indicate a problem at the same time.
• The washer lid is opened.
The number window LED display abnormal code: and the electric buzzer sounds to
indicate a problem at the same time.
4) Abnormal condition of child lock.
Running in setting child lock, the washer lid is opened beyond 4 seconds.
The number window LED display abnormal code: and the electric buzzer sounds to
indicate a problem at the same time.
5) Abnormal condition of water level sensor.
The water level sensor malfunctions or the water level is overrunning the alert level when the
water does not stop.
The number window LED display abnormal code: and the electric buzzer sounds to
indicate a problem at the same time.
6) Abnormal condition of load sensor.
The number window LED display abnormal code: and the electric buzzer sounds to
indicate a problem at the same time.

3
CIRCUIT DIAGRAM
THOUBLESHOOTING
a. Power Source
Yes
No
COLOR SYMBOL
Gr
Bl
G
B
LB
Br
O
P
R
W
Y
V
GRAY
BLUE
GREEN
BLACK
LIGHT BLUE
BROWN
ORANGE
PINK
RED
WHITE
YELLOW
VIOLET
TROUBLE INSPECTION CAUSES REMEDY
Any indications
and beep do not
work when
power switch is
on and the start
button is pressed
INSPECTION
Is fuse blown? Deterioration of fuse.
Motor is defective.
Capacitor is defective.
Replace.
Replace.
Replace.
Poor connect of 6-pin
connectors (blue&white).
Control circuit board is
defective
Repair or replace.
Replace.

4
Hose joint assembly
Cushion
Filter
Does water stop
when the plug
is removed or
power switch is
OFF?
b. Water Supply
Yes
No
Low
High
Note: When removing the flow sheet, reinstate the filter in place correctly.
Yes
No
TROUBLE INSPECTION CAUSES REMEDYINSPECTION
Water does not
flow when the
power switch is
on and start
button is pressed.
Does humming
noise come on
from water
valve？
Something on the filter of
the water valve or hose
joint assembly.
Clean the filter.
Poor connect of 6-pin
connectors (blue& white).
Water valve is defective.
Water level sensor is
defective.
Control circuit board is
defective.
Repair or replace.
Replace.
Replace.
Replace.
Water is not
supplied normally.
Check water
pressure.
Remove the flow
sheet of the water
valve.
Replace the water
valve.
Clean the filter on
the water valve or
hose joint
assembly.
Replace the water
valve.
Water does not stop
Something in the air trap
hose or air leaks from a
part related water level
sensor system.
Water level sensor is
defective.
Control circuit board is
defective
.
Something on the
diaphragm on the water
valve.
Diaphragm is deformed
Clean or replace.
Replace .
Replace.
Replace or
disassemble the
valve and clean
the diaphragm
Replace
The height of drain hose is
less
than 0.7m.
Make the height of
drain hose is not less
than 0.7m.

5
Bearing ass
’
y is defective. Replace.
Motor wires are
dis-connected.
Capacitor wires are
dis
-
connected
.
Capacitor is defective.
Motor coil shorten.
Brake lining on bearing ass
’
y
is worn out.
Brake lever ass
’
y is defective.
Torque motor is broken.
Brake lining is worn out.
Brake lever ass
’
y is defective.
Foreign matter in drain hose.
Valve bellow is deformed.
Pump lead wire is
disconnected.
Control circuit board is
defective.
c. Wash/Rinse
No
Yes
No
Yes
No
Yes
Yes
No
No
d. Drain
Yes
No
TROUBLE INSPECTION CAUSES REMEDY
Washing cycle does
not start even if
water keeps the
selected water level.
INSPECTION
Does the spin tub
rotated normally
when the
COURSE button
is set to SPIN?
Bearing ass
’
y is defective.
Poor connect of 6-pin
connectors (blue & white)
Thermostat on motor is
opened.
Control circuit board is
defective.
Replace.
Replace.
Repair or replace
after cooling down.
Replace.
Does the pulsator
rotate by hand?
Does humming
noise come on
from motor?
Replace or repair.
Replace or repair.
Replace.
Replace.
The spin tub rotates
together with the
pulsator during
washing or rinsing
cycle.
Is the torque motor
working normally? Replace bearing ass
’
y.
Replace bearing ass
’
y.
Replace.
Note:
Brake-work is
normal when spin
tub stops within 10
sec. under no-load.
Does brake-work
normally?
Replace bearing ass
’
y.
Repl
ace
bearing
ass
’
y.
Water does not
drain out.
Is the built-in
pump working
normally？
Clean drain hose
inside.
Repair or replace.
Replace.

6
e. Spin Drying
Yes
No
TROUBLE INSPECTION CAUSES REMEDYINSPECTION
Drain takes time too
long. Drain hose
ass
’
y is deformed.
Hose is connected in the
wrong way.
Hose is too long or position of
hose is too high.
Repair or replace.
Repair.
Repair.
Note: In draining, the water lever sensor can
not reset in 8minutes.
The number window LED display
abnormal code: and begin blinking
on and off at the same time and the
electric buzzer sounds to indicate a
problem.
Note: In draining, the water level sensor can
not reset in 8 minutes.
The number window LED display
abnormal code: and begin blinking
on and off at the same time and the
electric buzzer sounds to indicate a
problem.
• If the Drain Hose is too long or high, it may
make draining impossible.
• The extend Drain Hose to a maximum long of
3 meters and maximum high of 10 centimeters.
Spin drying cycle
does not work.
INSPECTION
Does safety
device work?
Machine inclines. Replace with level.
The V-belt is slipping.
The V-belt is snapped.
Small pulley mounting
screw is loosed.
Motor is disconnected or
burnt.
Capacitor is broken or
disconnected.
Bearing ass
’
y is defective.
Torque motor is defective.
Brake lever is defective.
Thermostat on motor is
opened.
Poor contact of 6-pin
connectors (blue &white).
Control circuit board is
defective.
Adjust the motor
position.
Replace.
Tighten up.
Replace.
Replace.
Replace.
Replace.
Repair or replace.
Repair or replace
after cooling down.
Repair or replace.
Replace.
Note:
1. The safety switch works 3 times
continuously or works 1 time in the
single program of spin-dry . The
number window LED display abnormal
code: and begin blinking on and off
at the same time and the electric buzzer
sounds to indicate a problem.
2. Do not disconnect the wire from the
capacitor, because this wire acts as
de-pressing noise from outside to the
micro-computer.

7
Operation of safety device
When the safety device works by abnormal swing of spin drum, machine works automatically to
stop Spin-Dry cycle and operates water supply valve to pour water into the Wash/Spin Tub and
then starts washing cycle for replacing washing clothes evenly.
After above operation has down twice, if safety device works again, machine will stop, and the
number window LED display abnormal code: and begin blinking on and off at the same time
and the electric buzzer sounds to indicate a problem.
• Open the Wash Lid and rearrange the clothes evenly around the Wash/Spin Tub.
• Close the Wash Lid and press the START/PAUSE button again.
f. Buzzing and rattling
Low
High
TROUBLE INSPECTION CAUSES REMEDYINSPECTIONINSPECTION
Start of spin-drying. Normal spin.Safety device work.
Electric circuit
counts operation
of safety device.
Electric circuit works to stop
spin when safety device
detects continuously three
times of abnormal swing of
spin drum.
Automatic
adjustment or
load.
Buzzing/rattling
during water
supply.
INSPECTION Something in water valve. Replace. INSPECTION
Is high water
pressure (more
than 4kg/cm
2
)?
Faucet open too far Adjust faucet
turning.
Stop of Spin-Dry
Agitation of load (Rinsing
for 2 minutes).
Water supply

8
Yes
No
TROUBLE INSPECTION CAUSES REMEDYINSPECTION
Buzzing/rattling
during washing
or rinsing.
Does some noise
sound during
spin drying?
Belt is slipping.
Pulley is loose.
Some part touch motor
Adjust.
Tighten.
Repair or replace
Something underneath
pulsator.
Pulsator is rubbing.
P
ulsator shaft is burnt.
Remove.
Adjust bearing ass
’
y.
Replace bearing ass
’
y.
Buzzing/rattling
during spin-dry. Is sound in low-pitched
monotone?
Bearings of bearing ass
’
y
is defective.
Replace.
Is variable sound
happened by
vibration?
Does noise sound
when the washer
begins to work?
Is clattering on
maximum
rotation?
Is flapping?
Machine is in unbalance.
Suspension rod ass
’
y is
worn out.
Belt is slipping
Motor pulley is loose.
Wire and/or air trap hose
is loose.
Place machine
evenly on base.
Replace.
Adjust.
Tighten up.
Tighten.

9
PART LIST
Key No. Part No. Description 中文名称 Q
’
ty
1 301B801701454 Control Circuit Board Complete 电脑板完成 1
2 ST1TN40160SE SCR 4×16 4X16 螺钉(电脑板安装用) 5
3 301B121000528 Panel sticker 控制板塑贴印刷完成 1
4 301B141400166 Lid Handle
上盖把手喷漆印刷完成 1
5 ST1TN40100SE SCR 4×10 4X10 螺钉(把手固定用) 4
6 3012160510146 Screw Lid 螺钉盖 4
7 3014201S02140 magnet
磁性开关用永磁铁 1
8 3012161404040 Washer Lid
洗涤上盖 1
8a 301B141200250 Washer Lid complete
洗涤上盖组件(虚拟件)
1
9 3012160613140 Hinge Shaft
上盖轴销 1
10 3012160717140 Lid Spring
盖板弹簧 1
11 301213179F140 Notice Label 注意铭牌 1
12 301B141500138 Back Plate 后板 1
13 3012324905140 Water Valve connector 进水阀连接器 1
14 ST1TN40120SE SCR 4×12 4X12 螺钉(后板安装用) 2
15 301B802300004 Safety Device Switch
桶开关组件 1
16 ST1TN40140SE SCR 4×14 4X14 螺钉(桶开关组件安装用) 2
17 ST1TN40120SE SCR 4×12 4X12 螺钉(进水阀和进水盒连接) 3
18 3014294S37140 Valve Assembly(Water Valve) 进水阀 1
19 3012212701140 Water Valve tie_in 进水阀接头 1
20 3010317136140 Pour Inlet assembly 进水盒组件 1
21 ST1TN40120SE SCR 4×12 4X12 螺钉(进水盒组件安装用) 3
22 3014291S03140 Response Switch(Water Level Sensor) 水位传感器 1
23 3012334002140 Hose Band 软管卡簧(水位传感器用) 1
24 3012324212140 Air Trip Hose 通气软管(水位传感器用) 1
25 3012143414140 Cushion 海绵套环 1
26 3012160140040 Top Plate 面架 1
27 ST1TN40120SE SCR 4×12 4X12 螺钉(面架安装用) 4
28 3012160510145 Screw Cap 螺钉盖 2
29 3012256137141 Detergent Tray 粉末盒印刷完成 1
30 3010161102140 Gradienter 水平仪 1
31 3012161202140 Gradienter Cover 水平仪罩 1
32 3012143454140 Cushion
橡胶垫(面架用) 2
33 3014292S04140 Reed Switch
磁性开关 1
34 STATN40100SE SCR 4×10 4X10 螺钉(
磁性开关压线片 用) 1
34a 3012152514140 Reed Switch fixture 压线片(
磁性开关 安装用) 1
34b 3012176220140 aluminum foil 100x100 铝箔(100X100 面架用) 1
35 301B801100042 Wire bunch 洗衣机线束 1
35a 3012152502140 Wire fix 导线束缚(通气软管及导线用) 2
36 301B111200041 Frame Complete 箱体铆接完成 1
37 Stopping Pin 止退销（包含在吊杆完成里） 4
38 Spring Damper Base 吊杆球座（包含在吊杆完成里） 4

10
Key No. Part No. Description 中文名称 Q
’
ty
39 3012912223140 SCR 4×8 4X8 螺钉(
后罩盖安装 用) 7
40 3012122232140 Back Cover 后罩盖 1
41 3012122101142 Frame Handle
箱体把手 2
42 3012122302140 Drain Cap
排水口盖 1
43 3012334001140 Hose Band 软管卡簧(排水内管和外桶) 1
44 3010324703140 Drain Hose (Inside) 排水内管组件 1
45 3012912203140 Special
screws M5×14 特种螺钉 M5×14 2
46 ST1TN40140SE SCR 4×14E
螺钉 4×14E 1
47 3010342014140
Drain valve Assembly 排水阀组件 1
51 3010325103141 Drain Hose assembly(Outside) 排水软管组件 1
54 3012334004140 Hose Band 软管卡簧(排水软管组件,附件) 1
55 3012152306042 Leg 底托 1
56 STATN40120SD- SCR 4×12 4X12 螺钉(底托安装用) 9
57 3010143007140 Adjuster Assembly 可调脚组件 1
58 3012234305140 Sound-Proof Board 底托屏蔽板 1
59 ST1TN40140SE SCR 4×14 4X14 螺钉(底托屏蔽板用,附件) 1
60 3012143401140 Cushion 缓冲垫 3
61 ST2TN60200SE SCR 6×20 6×20 螺钉(缓冲垫安装用) 3
62 3012152503140 Lead Stay
导线卡 2
63 3010812012140 Cord Assembly 电源线组件 1
64 3012152501140 Cord Stay
电源线束缚 1
65 ST1TN40100SE SCR 4×10 4X10 螺钉(电容器安装用) 1
66 3014295S01140 Capacitor Assembly, 10µF/450V Ac 电容器组件 1
67 3010856501140 Earthing Wire Assembly 地线组件 1
68 SFSPG40100SA SCR 4×10A 4X10 螺钉(箱体接地用) 2
69 SVCNN40KA--- Washer SPR 4 垫片(箱体接地用) 2
70 3012813007140 Part Bag
扎线塑料袋 1
70a 3012234109140 Sound-Proof Board
防音板 1
71 3012871103140 Compressed Connector 压接套管 4
72 3012871102140 Compressed Connector 压接套管 1
73 3012411301140 Pulsator Screw 波轮螺钉 1
74 3012411401140 Pulsator Screw Washer
波轮螺钉衬垫 1
75 3012411006043 Pulsator 波轮 1
76 3012411501140 Pulsator Washer 波轮垫片 1
77 3012221203140 Outer Tub Cover 外桶盖 1
78 ST1TN40140SE SCR 4×14 4X14 螺钉(外桶盖安装用) 2
79 3012912202140 Special Screw assembly 螺栓组件(脱水桶固定用) 4
80 3010240029043 Spin Tub Complete
脱水桶完成(虚拟件) 1
81 3010240105043 Balance Weight Assembly
平衡环组件（无图）(虚拟件) 1
82 3012131728140 Notice Label
注意铭板 1
83 3010241118043 Spin Tub Assembly
脱水桶组件 1
84 ST1TN50210UK SCR 5×21K 5X21 螺钉(平衡环安装用) 6
85 3012240208140 Spin Tub Boss
脱水桶法兰 1
86 201D0067 Motor Complete 电机完成 1