Whispbar K090W User manual

K090W
Fitting Kit
EN Fitting Instructions for Basic Carrier
DMontageanleitung für Basisträgersystem
ES Instrucciones de montaje para el sistema de transporte.
FInstructions de montage pour Basic Carrier
NO Monteringsanvisning for takstativ
PT Instruções de Montagem para sistema de transporte.
RU Установочные Инструкции для Поперечных Балок
x 1 x 4 x 4 x 2
x 2 x 4
Revision No: 4C 1

Fitting Kit K090W
MAX kgs (lbs)
W/P WHD
Peugeot
306 , 4dr Sedan 93-02 EU 50 kgs (110 lbs) 50 kgs (110 lbs)
306 , 4dr Sedan Aug 93-02 NZ 50 kgs (110 lbs) 50 kgs (110 lbs)
306 , 4dr Sedan Mar 94-Dec 01 AU 50 kgs (110 lbs) 50 kgs (110 lbs)
306 , 5dr Hatch 93-02 AU 45 kgs (99 lbs) 45 kgs (99 lbs)
306 , 5dr Hatch 93-02 NZ 45 kgs (99 lbs) 45 kgs (99 lbs)
306 , 5dr Hatch 93-02 US 45 kgs (99 lbs) 45 kgs (99 lbs)
306 , 5dr Hatch 93-02 EU 45 kgs (99 lbs) 45 kgs (99 lbs)
405 , 4dr Sedan 87-97 EU 50 kgs (110 lbs) 50 kgs (110 lbs)
405 , 4dr Sedan Feb 93-Jun 97 NZ 50 kgs (110 lbs) 50 kgs (110 lbs)
405 , 5dr Estate 87-97 EU 50 kgs (110 lbs) 50 kgs (110 lbs)
405 , 5dr Wagon Jun 93-Oct 97 NZ 50 kgs (110 lbs) 50 kgs (110 lbs)
2

Fitting Kit EN
K090W
First Time Installation
●Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
●This kit fits type A, B, C and D.
●These instructions show type A crossbar
fitted. They also apply to type B, C and D.
NOTE: Clamp images in these instructions may
not be representative of the clamps in this kit
3

Fitting Kit EN
K090W
●Use keys to remove covers.
●Use hex screwdriver to reverse adjusting
screw 10 turns.
●Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment.
●Ensure each end of the crossbar is
adjusted equally.
4

Fitting Kit EN
K090W
●Remove locking screw.
●Apply protective strip as shown.
Trim if required.
●It is important to put the clamps in the
correct position on the vehicle.
●Letters refer to the part numbers stamped
on clamps.
●Clamp Part Number:
A = 290A
B = 291A
5

Fitting Kit EN
K090W
●Attach clamp to each leg. NOTE; clamps
may have labels showing their positions on
the vehicle (For example; "Front Right").
●Refit locking screw so that it goes through
the hole in the clamp. Do not begin to
tighten the locking screw.
●Fit rubber pad (supplied with crossbar) to
foot.
6

Fitting Kit EN
K090W
●Make sure the pad fits into the holes
underneath the foot.
●Place crossbar on vehicle. Minimum
recommended spacing between the bars is
700mm (27 1/2") (unless otherwise stated).
●Clamps directly to edge of roof under the
doors, pin locates in hole on vehicle
●Please check the rear of this manual for
information relating specifically to your
vehicle.
Fitment
●Pull back rubber seal to expose fixed points
on vehicle body.
7

Fitting Kit EN
K090W
●Reveal the fixed points. They may be
concealed behind a painted sticker.
●Press adjusting screw to adjust the leg
positions on the crossbar.
●Tighten adjusting screw to 5 Nm (3.7 ft lb).
8

Fitting Kit EN
K090W
●Place clamp over the mounting hole
●Fit a fibre washer on each capscrew and
attach clamps to the vehicle body using the
capscrews.
●Tighten clamp to roof.
●Do not over tighten.
●Tighten locking screw on both legs evenly.
9

Fitting Kit EN
K090W
●Refit rubber seal over the clamp.
●Check crossbar is securely attached to the
vehicle.
●Use keys to fit and lock covers
10