Whispbar K117W User manual

K117W
Fitting Kit
EN Fitting Instructions for Basic Carrier
DMontageanleitung für Basisträgersystem
ES Instrucciones de montaje para el sistema
de transporte
FInstructions de montage pour Basic Carrier
NO Monteringsanvisning for takstativ
PT Instruções de Montagem para sistema de
transporte.
RU Установочные Инструкции для
Поперечных Балок
x 4 x 2 x 2
Revision No: 3C 1

Fitting Kit K117W
MAX kgs (lbs)
W/P WHD
Toyota
Camry 20 Series, 5dr Wagon May 98-Aug 02 AU 75 kgs (165 lbs) 75 kgs (165 lbs)
Camry, 5dr Estate 97-01 EU 75 kgs (165 lbs) 75 kgs (165 lbs)
Camry, 5dr Estate 97-01 CN 75 kgs (165 lbs) 75 kgs (165 lbs)
Camry, 5dr Wagon Sep 97-Sep 02 NZ 75 kgs (165 lbs) 75 kgs (165 lbs)
Vienta, 5dr Wagon Aug 97-Oct 00 AU 75 kgs (165 lbs) 75 kgs (165 lbs)
2

Fitting Kit K117W
X
A B C 1 2 3
Camry 20 Series, 5dr Wagon May 98-Aug 02 (AU) -300mm 300mm - 844mm 835mm -
-11 -13/16ths" 11 13/16ths" - 33 1/4ths" 32 7/8ths" -
Camry, 5dr Estate 97-01 (EU) -300mm 300mm - 844mm 835mm -
-11 -13/16ths" 11 13/16ths" - 33 1/4ths" 32 7/8ths" -
Camry, 5dr Estate 97-01 (CN) -300mm 300mm - 844mm 835mm -
-11 -13/16ths" 11 13/16ths" - 33 1/4ths" 32 7/8ths" -
Camry, 5dr Wagon Sep 97-Sep 02 (NZ) -300mm 300mm - 844mm 835mm -
-11 -13/16ths" 11 13/16ths" - 33 1/4ths" 32 7/8ths" -
Vienta, 5dr Wagon Aug 97-Oct 00 (AU) -300mm 300mm - 844mm 835mm -
-11 -13/16ths" 11 13/16ths" - 33 1/4ths" 32 7/8ths" -
3

Fitting Kit EN
K117W
First Time Installation
●Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
●This kit fits type A, B, C and D.
●These instructions show type A crossbar
fitted. They also apply to type B, C and D.
NOTE: Clamp images in these instructions may
not be representative of the clamps in this kit
4

Fitting Kit EN
K117W
●Use keys to remove covers.
●Use hex screwdriver to reverse adjusting
screw 10 turns.
●Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment method.
●Ensure each end of the crossbar is
adjusted equally.
5

Fitting Kit EN
K117W
●Remove locking screw.
●Apply protective strip as shown.
Trim if required.
●It is important to put the clamps in the
correct position on the vehicle.
●Letters refer to the part numbers stamped
on clamps.
●Clamp Part Number:
A = 262B
B = 312B
6

Fitting Kit EN
K117W
●Attach clamp to each leg. NOTE; clamps
may have labels showing their positions on
the vehicle (For example; "Front Right").
●Refit locking screw so that it goes through
the hole in the clamp. Do not begin to
tighten the locking screw.
●Fit rubber pad (supplied with crossbar) to
foot.
7

Fitting Kit EN
K117W
●Make sure the pad fits into the holes
underneath the foot.
Fitment
●Place crossbar on vehicle. Minimum
recommended spacing between the bars is
700mm (27 1/2") (unless otherwise stated).
●Clamps over rubber door frame mouldings.
●Press adjusting screw to adjust the leg
positions on the crossbar.
8

Fitting Kit EN
K117W
●Tighten adjusting screw to 2 Nm (1.5 ft lb)
hand tight.
●Tighten locking screw on both legs evenly.
●Check crossbar is securely attached to the
vehicle.
9

Fitting Kit EN
K117W
●Use keys to fit and lock covers
CAUTION: Recheck all fasteners immediately after
a load is applied to the crossbars.
Regularly check screws are tight.
10