Whispbar K193W User manual

K193W
Fitting Kit
EN Fitting Instructions for Basic Carrier
x 2 x 2 x 2 x 2
Revision No: 4D 1

Fitting Kit K193W
MAX kgs (lbs)
W/P WHD
Holden
Caprice, 4dr Sedan 06-+ AU 75 kgs (165 lbs) 75 kgs (165 lbs)
Caprice, 4dr Sedan 06-+ NZ 75 kgs (165 lbs) 75 kgs (165 lbs)
Commodore VE, 2dr Ute Oct 07-13 NZ 25 kgs (55 lbs) 25 kgs (55 lbs)
Commodore VE, 2dr Ute Sep 07-13 AU 25 kgs (55 lbs) 25 kgs (55 lbs)
Commodore VF, 2dr Ute 13-+ AU 25 kgs (55 lbs) 25 kgs (55 lbs)
Commodore VF, 2dr Ute 13-+ NZ 25 kgs (55 lbs) 25 kgs (55 lbs)
Statesman WM, 4dr Sedan 06-+ NZ 75 kgs (165 lbs) 75 kgs (165 lbs)
Statesman WM, 4dr Sedan 06-+ AU 75 kgs (165 lbs) 75 kgs (165 lbs)
2

Fitting Kit K193W
X
A B C 1 2 3
Caprice, 4dr Sedan 06-+ (AU) -280mm 420mm - 934mm 915mm -
-11" 16 9/16ths" - 36 3/4ths" 36" -
Caprice, 4dr Sedan 06-+ (NZ) -280mm 420mm - 934mm 915mm -
-11" 16 9/16ths" - 36 3/4ths" 36" -
Commodore VE, 2dr Ute Oct 07-13 (NZ) -280mm - - 950mm - -
-11" - - 37 3/8ths" - -
Commodore VE, 2dr Ute Sep 07-13 (AU) -280mm - - 950mm - -
-11" - - 37 3/8ths" - -
Commodore VF, 2dr Ute 13-+ (AU) -280mm - - 950mm - -
-11" - - 37 3/8ths" - -
Commodore VF, 2dr Ute 13-+ (NZ) -280mm - - 950mm - -
-11" - - 37 3/8ths" - -
Statesman WM, 4dr Sedan 06-+ (NZ) -280mm 420mm - 955mm 928mm -
-11" 16 9/16ths" - 37 5/8ths" 36 9/16ths" -
Statesman WM, 4dr Sedan 06-+ (AU) -280mm 420mm - 955mm 928mm -
-11" 16 9/16ths" - 37 5/8ths" 36 9/16ths" -
3

Fitting Kit EN
K193W
First Time Installation
●Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
●This kit fits type A, B, C and D.
●These instructions show type A crossbar
fitted. They also apply to type B, C and D.
NOTE: Clamp images in these instructions may
not be representative of the clamps in this kit
4

Fitting Kit EN
K193W
●Use keys to remove covers.
●Use hex screwdriver to reverse adjusting
screw 10 turns.
●Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment method.
●Ensure each end of the crossbar is
adjusted equally.
5

Fitting Kit EN
K193W
●Remove locking screw.
●Apply protective strip as shown.
Trim if required.
●This setup is applicable for one crossbar
only.
●Letters refer to the part numbers stamped
on clamps.
●Clamp Part Number:
A = 425B
6

Fitting Kit EN
K193W
●This setup is applicable for two crossbars
only.
●It is important to put the clamps in the
correct position on the vehicle.
●Letters refer to the part numbers stamped
on clamps.
●Clamp Part Number:
A = 425B
B = 426B
●Attach clamp to each leg. NOTE; clamps
may have labels showing their positions on
the vehicle (For example; "Front Right").
●Refit locking screw so that it goes through
the hole in the clamp. Do not begin to
tighten the locking screw.
7

Fitting Kit EN
K193W
●Fit rubber pad (supplied with crossbar) to
foot.
●Make sure the pad fits into the holes
underneath the foot.
Fitment
●Place crossbar on vehicle. Minimum
recommended spacing between the bars is
700mm (27 1/2") (unless otherwise stated).
●Please check the front of this manual for
information relating specifically to your
vehicle.
8

Fitting Kit EN
K193W
●Clamps over body trim.
●A= Clamp
B= Roof line
C= Body trim
D= Protective strip
●Press adjusting screw to adjust the leg
positions on the crossbar.
●Tighten adjusting screw to 5 Nm (3.7 ft lb)
hand tight.
9

Fitting Kit EN
K193W
●Tighten locking screw on both legs evenly.
●Check crossbar is securely attached to the
vehicle.
●Use keys to fit and lock covers
10