Whispbar K937W User manual

K937W
Fitting Kit
EN Fitting Instructions for Basic Carrier
x 6 x 6 x 1 x 6
x 3 x 3 x 6 x 6
x 6
Revision No: 3C 1

Fitting Kit K937W
MAX kgs (lbs)
W/P WHD
Mercedes
Sprinter, 5dr Van 07-+ AU 75 kgs (165 lbs) 100 kgs (220 lbs)
Sprinter, 5dr Van 07-+ NZ 75 kgs (165 lbs) 100 kgs (220 lbs)
Sprinter, 5dr Van 07-+ EU 75 kgs (165 lbs) 100 kgs (220 lbs)
Sprinter, 5dr Van 07-+ ZA 75 kgs (165 lbs) 100 kgs (220 lbs)
Sprinter, 5dr Van 07-+ US 75 kgs (165 lbs) 100 kgs (220 lbs)
2

Fitting Kit K937W
Sprinter, 5dr Van 07-+ (AU)
Sprinter, 5dr Van 07-+ (NZ)
Sprinter, 5dr Van 07-+ (EU)
Sprinter, 5dr Van 07-+ (ZA)
Sprinter, 5dr Van 07-+ (US)
3
X
A B C 1 2 3
-300mm 1080mm 1990mm 1270mm 1270mm 1270mm
-11 -13/16ths" 42 1/2ths" 78 3/8ths" 50" 50" 50"
-300mm 1080mm 1990mm 1270mm 1270mm 1270mm
-11 -13/16ths" 42 1/2ths" 78 3/8ths" 50" 50" 50"
-300mm 1080mm 1990mm 1270mm 1270mm 1270mm
-11 -13/16ths" 42 1/2ths" 78 3/8ths" 50" 50" 50"
-300mm 1080mm 1990mm 1270mm 1270mm 1270mm
-11 -13/16ths" 42 1/2ths" 78 3/8ths" 50" 50" 50"
-300mm 1080mm 1990mm 1270mm 1270mm 1270mm
-11 -13/16ths" 42 1/2ths" 78 3/8ths" 50" 50" 50"
D
800mm
31 1/2"
800mm
31 1/2"
800mm
31 1/2"
800mm
31 1/2"
800mm
31 1/2"
4
1270mm
50"
1270mm
50"
1270mm
50"
1270mm
50"
1270mm
50"

Fitting Kit EN
K937W
First Time Installation
●Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
●This kit fits type A, B, C and D.
●These instructions show type A crossbar
fitted. They also apply to type B, C and D.
●Use keys to remove covers.
4

Fitting Kit EN
K937W
●Use hex screwdriver to reverse adjusting
screw 10 turns.
●Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment method.
●Ensure each end of the crossbar is
adjusted equally.
●Set bars to length (revert to rear of these
instructions).
●Please check the front of this manual for
information relating specifically to your
vehicle.
5

Fitting Kit EN
K937W
●Tighten adjusting screw to 2 Nm (1.5 ft lb)
hand tight.
●Remove plastic clamp block by gripping bar
leg with fingers and push firmly with
thumbs until clamp block drops out behind
leg.
●Remove both pins from each leg. Use
tapered end of spanner located inside left
hand cover to assist.
6

Fitting Kit EN
K937W
●Detach foot from leg. Store loose parts in a
safe place.
●Repeat for all legs.
●Assemble foot from kit into leg.
●Insert pins through foot into leg.
7

Fitting Kit EN
K937W
●Select plastic internal block (from fitting kit)
and insert into foot.
●Repeat for all legs.
●Refer to the top side of the pad for the part
number.
●Letters refer to the pad part numbers and
position.
●Pad Part Number:
A = 244A
B = 245A
8

Fitting Kit EN
K937W
●Fit rubber pads (supplied with fitting kit) to
foot. Pad may vary in shape to that shown.
Fitment
●Remove sealant as shown.
●Open or remove fixed-point covers.
9

Fitting Kit EN
K937W
●Place crossbar into gutter of vehicle.
●Place large flat washer onto bolt.
●With assistance, fit washer and nut loosely
onto each of the cap screws from inside the
canopy.
●Tighten with provided 10mm (3/8")
spanner.
●Ensure the plastic knob is in the position
shown when fully tightened.
●Repeat for all four positions.
10