Whispbar K325W User manual

K325W
Fitting Kit
EN Fitting Instructions for Basic Carrier
DMontageanleitung für Basisträgersystem
ES Instrucciones de montaje para el sistema de transporte.
FInstructions de montage pour Basic Carrier
NO Monteringsanvisning for takstativ
PT Instruções de Montagem para sistema de transporte.
RU Установочные Инструкции для Поперечных Балок
x 8 x 4 x 1 x 4
x 4 x 4 x 4 x 4
x 4 x 4
Revision No: 5C 1

Fitting Kit EN
K325W
First Time Installation
●Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
●This kit fits type A, B, C and D.
●These instructions show type A crossbar
fitted. They also apply to type B, C and D.
●Use keys to remove covers.
2

Fitting Kit EN
K325W
●Use hex screwdriver to reverse adjusting
screw 10 turns.
●Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment.
●Ensure each end of the crossbar is
adjusted equally.
●Please check the rear of this manual for
information relating specifically to your
vehicle.
3

Fitting Kit EN
K325W
●Remove plastic clamp block by gripping bar
leg with fingers and push firmly with
thumbs until clamp block drops out behind
leg.
●Remove both pins from each leg. Use
tapered end of spanner located inside left
hand cover to assist.
●Detach foot from leg. Store loose parts in a
safe place.
●Repeat for all legs.
4

Fitting Kit EN
K325W
●Assemble metal loadplate and rubber pad
from the fitting kit.
●Repeat for all four items.
●Assemble metal loadplate into leg. Ensure
loadplate interlocks with the leg.
●Using short capscrew and washer, secure
assembly onto leg (use Hex Screwdriver
supplied with crossbar to assist)
●Repeat for all legs.
5

Fitting Kit EN
K325W
●Pull rubber pad back slightly and insert
location peg into the rear position on the
metal loadplate. Peg will click into place.
●Place crossbar on vehicle. Minimum
recommended spacing between the bars is
700mm (27 1/2") (unless otherwise stated).
●Crossbar can be positioned anywhere
along the roof rail.
●Make sure there is no interference between
what you intend to carry with aerials,
sunroof or tailgate.
●Ensure location peg engages the inner side
of the rails.
●Adjust crossbar in or out to suit vehicle.
Refer to the crossbar instructions for
crossbar adjustment.
●Ensure that the crossbar is adjusted evenly
at both ends.
6

Fitting Kit EN
K325W
●Tighten adjusting screw to 5 Nm (3.7 ft lb).
●Temporarily mark with masking tape or
pencil the position of crossbars on the rail.
●Remove crossbar off vehicle and turn
upside down. Select metal clamp and fit
small tongue into position 2 marked on the
leg.
7

Fitting Kit EN
K325W
●Swing clamp towards metal loadplate and
check clamp tongue is engaged into
position.
●Select coach bolt and insert through metal
clamp slot.
●While holding clamp and coach bolt, turn
crossbar over to upright position and
loosely assemble red plastic knob to the
coach bolt. Do not start to tighten.
●Repeat for all legs.
8

Fitting Kit EN
K325W
Fitment
●Place crossbars back onto vehicle roof by
placing one end of crossbar on the rail and
swing the other into previously marked
position.
●Ensure the clamp engages correctly on
inside of roof rail.
●Tighten the red plastic knob. Large Hex
Key can be used to help tightening knob.
●Do not over tighten.
●Ensure plastic red knob is vertical when
fully tightened.
9

Fitting Kit EN
K325W
●Check crossbar is securely attached to the
vehicle.
●Use keys to fit and lock covers
Fitment to Subaru Legacy or Liberty Wagon Sep
03+ ONLY
●Open or remove fixed-point covers.
10