Whispbar K952W User manual

K952W
Fitting Kit
EN Fitting Instructions for Basic Carrier
x 1 x 1 x 2 x 1
x 1 x 1 x 4 x 1
Revision No: 2B 1

Fitting Kit K952W
x 1 x 4 x 4 x 4
x 4
2

Fitting Kit K952W
MAX kgs (lbs)
W/P WHD
Honda
Odyssey, 5dr MPV 13-+ AU 50 kgs (110 lbs) 50 kgs (110 lbs)
Odyssey, 5dr MPV 14-+ NZ 50 kgs (110 lbs) 50 kgs (110 lbs)
3

Fitting Kit K952W
X
A B C 1 2 3
Odyssey, 5dr MPV 13-+ (AU) 220mm 1115mm - 970mm 903mm -
8 11/16ths" 43 7/8ths" - 38 3/16ths" 35 9/16ths" -
Odyssey, 5dr MPV 14-+ (NZ) 220mm 1115mm - 970mm 903mm -
8 11/16ths" 43 7/8ths" - 38 3/16ths" 35 9/16ths" -
4

Fitting Kit EN
K952W
First Time Installation
●Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
●This kit fits type A, B, C and D.
●These instructions show type A crossbar
fitted. They also apply to type B, C and D.
●Use keys to remove covers.
5

Fitting Kit EN
K952W
●Use hex screwdriver to reverse adjusting
screw 10 turns.
●Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment method.
●Ensure each end of the crossbar is
adjusted equally.
●Attaches to factory-fitted mounting points
●Please check the front of this manual for
information relating specifically to your
vehicle.
●Adjust crossbar in or out to suit vehicle.
Refer to the crossbar instructions for
crossbar adjustment.
6

Fitting Kit EN
K952W
●Tighten adjusting screw to 2 Nm (1.5 ft lb)
hand tight.
●Remove plastic clamp block by gripping bar
leg with fingers and push firmly with
thumbs until clamp block drops out behind
leg.
●Select plastic internal block (from fitting kit)
and insert into foot.
●Repeat for all legs.
7

Fitting Kit EN
K952W
Fitment
●Lift and pull ditch molding back towards
you. Note: ditch molding remains on
vehicle.
●Remove factory clips.
●Mark a reference point for the front and
rear mounting points with a pen as shown.
●Use drill bit supplied, to drill holes in
marked positions.
●Place block and protective foam under
ditch molding.
8

Fitting Kit EN
K952W
●Re-install rubber ditch mould back into roof
channel and click into place.
●Attach hex nut adaptor to stud as shown.
Tighten with the spanner provided.
●Select grubscrews and screw into the
vehicle's fixed points.
●Do not over tighten.
●Repeat for all four positions.
●Refer to the underside of the pad for the
part number.
9

Fitting Kit EN
K952W
●It is important to put the pads in the correct
position on the vehicle.
●Letters refer to the pad part numbers and
position.
●Pad Part Number:
A = 219
B = 222
C = 223
●Place crossbars on pads ensuring the pads
fit into the holes underneath the foot and
the grubscrew passes through the hole in
the foot.
●Repeat for all four positions.
●Tighten the plastic knob. The side with the
nut showing should be facing up.
10