Whispbar K1010W User manual

K1010W
Fitting Kit
EN Fitting Instructions for Basic Carrier
x 1 x 1 x 1 x 1
x 4 x 1 x 4 x 1
x 4 x 4
Revision No: 2B 1

Fitting Kit K1010W
MAX kgs (lbs)
W/P WHD
Mazda
CX-9, 5dr SUV 16-+ EU 75 kgs (165 lbs) 75 kgs (165 lbs)
CX-9, 5dr SUV 16-+ CN 75 kgs (165 lbs) 75 kgs (165 lbs)
CX-9, 5dr SUV Jul 16-+ NZ 75 kgs (165 lbs) 75 kgs (165 lbs)
CX-9, 5dr SUV Jul 16-+ AU 75 kgs (165 lbs) 75 kgs (165 lbs)
2

Fitting Kit K1010W
X
A B C 1 2 3
CX-9, 5dr SUV 16-+ (EU) -285mm 490mm - 980mm 940mm -
-11 -1/4ths" 19 5/16ths" - 38 9/16ths" 37" -
CX-9, 5dr SUV 16-+ (CN) -285mm 490mm - 980mm 940mm -
-11 -1/4ths" 19 5/16ths" - 38 9/16ths" 37" -
CX-9, 5dr SUV Jul 16-+ (NZ) -285mm 490mm - 980mm 940mm -
-11 -1/4ths" 19 5/16ths" - 38 9/16ths" 37" -
CX-9, 5dr SUV Jul 16-+ (AU) -285mm 490mm - 980mm 940mm -
-11 -1/4ths" 19 5/16ths" - 38 9/16ths" 37" -
3

Fitting Kit EN
K1010W
First Time Installation
●Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
●This kit fits type A, B, C and D.
●These instructions show type A crossbar
fitted. They also apply to type B, C and D.
●Use keys to remove covers.
4

Fitting Kit EN
K1010W
●Use hex screwdriver to reverse adjusting
screw 10 turns.
●Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment method.
●Ensure each end of the crossbar is
adjusted equally.
●Attaches to factory-fitted mounting points
●Please check the front of this manual for
information relating specifically to your
vehicle.
●Adjust crossbar in or out to suit vehicle.
Refer to the crossbar instructions for
crossbar adjustment.
5

Fitting Kit EN
K1010W
●Tighten adjusting screw to 2 Nm (1.5 ft lb)
hand tight.
●Remove plastic clamp block by gripping bar
leg with fingers and push firmly with
thumbs until clamp block drops out behind
leg.
●Select plastic internal block (from fitting kit)
and insert into foot.
●Repeat for all legs.
6

Fitting Kit EN
K1010W
Fitment
●Lift and pull ditch moulding back towards
you and remove from the vehicle.
●Locate ditch mouldings on roof.
●Measure from the front of the ditch mould
at 310mm and 1085mm.
●Mark a reference point for the front and
rear mounting points with a pen as shown.
●Use drill bit supplied, to drill holes in
marked positions.
7

Fitting Kit EN
K1010W
●Re-install rubber ditch mould back into roof
channel and click into place.
●Select grubscrews and screw into the
vehicle's fixed points.
●Do not over tighten.
●Repeat for all four positions.
●Refer to the underside of the pad for the
part number.
8

Fitting Kit EN
K1010W
●It is important to put the pads in the correct
position on the vehicle.
●Letters refer to the pad part numbers and
position.
●Pad Part Number:
A = 229A
B = 230A
C = 233A
D = 234A
●Place crossbars on pads ensuring the pads
fit into the holes underneath the foot and
the grubscrew passes through the hole in
the foot.
●Repeat for all four positions.
●Tighten the plastic knob. The side with the
nut showing should be facing up.
9

Fitting Kit EN
K1010W
●Ensure the plastic knob is in the position
shown when fully tightened.
●Repeat for all legs.
●Check crossbar is securely attached to the
vehicle.
●Use keys to fit and lock covers
●If crossbars are removed, please install the
rubber plugs into the ditch moulding.
10