Whispbar K377 User manual

K377
Fitting Kit
EN Fitting Instructions for Basic Carrier
x 4 x 4
Revision No: 6F 1

Fitting Kit K377
MAX kgs (lbs)
W/P WHD
Audi
A4, 4dr Sedan 01-07 ZA 75 kgs (165 lbs) 75 kgs (165 lbs)
A4, 4dr Sedan 01-08 EU 75 kgs (165 lbs) 75 kgs (165 lbs)
A4, 4dr Sedan 01-08 AU 75 kgs (165 lbs) 75 kgs (165 lbs)
A4, 4dr Sedan 01-08 NZ 75 kgs (165 lbs) 75 kgs (165 lbs)
A4, 4dr Sedan 01-08 CN 75 kgs (165 lbs) 75 kgs (165 lbs)
A4, 4dr Sedan 02-08 US 75 kgs (165 lbs) 75 kgs (165 lbs)
S4, 4dr Sedan 04-05 US 75 kgs (165 lbs) 75 kgs (165 lbs)
S4, 4dr Sedan 06-08 US 75 kgs (165 lbs) 75 kgs (165 lbs)
S4, 4dr Sedan 06-08 US 75 kgs (165 lbs) 75 kgs (165 lbs)
Seat
Exeo, 4dr Sedan 08-13 EU 75 kgs (165 lbs) 75 kgs (165 lbs)
2

Fitting Kit K377
X
A B C 1 2 3
A4, 4dr Sedan 01-07 (ZA) -335mm 360mm - 855mm 820mm -
-13 -3/16ths" 14 3/16ths" - 33 11/16ths" 32 5/16ths" -
A4, 4dr Sedan 01-08 (EU) -335mm 360mm - 855mm 820mm -
-13 -3/16ths" 14 3/16ths" - 33 11/16ths" 32 5/16ths" -
A4, 4dr Sedan 01-08 (AU) -335mm 360mm - 855mm 820mm -
-13 -3/16ths" 14 3/16ths" - 33 11/16ths" 32 5/16ths" -
A4, 4dr Sedan 01-08 (NZ) -335mm 360mm - 855mm 820mm -
-13 -3/16ths" 14 3/16ths" - 33 11/16ths" 32 5/16ths" -
A4, 4dr Sedan 01-08 (CN) -335mm 360mm - 855mm 820mm -
-13 -3/16ths" 14 3/16ths" - 33 11/16ths" 32 5/16ths" -
A4, 4dr Sedan 02-08 (US) -335mm 360mm - 855mm 820mm -
-13 -3/16ths" 14 3/16ths" - 33 11/16ths" 32 5/16ths" -
Exeo, 4dr Sedan 08-13 (EU) -335mm 355mm - 840mm 810mm -
-13 -3/16ths" 14" - 33 1/16ths" 31 7/8ths" -
S4, 4dr Sedan 04-05 (US) -335mm 360mm - 850mm 820mm -
-13 -3/16ths" 14 3/16ths" - 33 7/16ths" 32 5/16ths" -
S4, 4dr Sedan 06-08 (US) -335mm 360mm - 850mm 820mm -
-13 -3/16ths" 14 3/16ths" - 33 7/16ths" 32 5/16ths" -
S4, 4dr Sedan 06-08 (US) -335mm 360mm - 880mm 855mm -
-13 -3/16ths" 14 3/16ths" - 34 5/8ths" 33 11/16ths" -
3

Fitting Kit EN
K377
First Time Installation
●Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
●This kit fits type A, B, C and D.
●These instructions show type A crossbar
fitted. They also apply to type B, C and D.
NOTE: Clamp images in these instructions may
not be representative of the clamps in this kit
4

Fitting Kit EN
K377
●Use keys to remove covers.
●Use hex screwdriver to reverse adjusting
screw 10 turns.
●Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment method.
●Ensure each end of the crossbar is
adjusted equally.
5

Fitting Kit EN
K377
●Remove locking screw.
●Apply protective strip as shown.
Trim if required.
●Attach clamp to each leg. NOTE; clamps
may have labels showing their positions on
the vehicle (For example; "Front Right").
6

Fitting Kit EN
K377
●Refit locking screw so that it goes through
the hole in the clamp. Do not begin to
tighten the locking screw.
●Fit rubber pad (supplied with crossbar) to
foot.
●Make sure the pad fits into the holes
underneath the foot.
7

Fitting Kit EN
K377
Fitment
●Place crossbar on vehicle. Minimum
recommended spacing between the bars is
700mm (27 1/2") (unless otherwise stated).
●Please check the front of this manual for
information relating specifically to your
vehicle.
●Locate vehicle's fixed points.
●Clamps directly to edge of roof under the
doors, pin locates in hole on vehicle
●Adjust the legs on the crossbar so that they
are positioned equally from the ends of the
crossbar, and the clamps engage firmly on
the body work of the vehicle.
●Tighten adjusting screw to 5 Nm (3.7 ft lb)
hand tight.
8

Fitting Kit EN
K377
●Tighten locking screw on both legs evenly.
●Check crossbar is securely attached to the
vehicle.
●Use keys to fit and lock covers
9

Fitting Kit EN
K377
CAUTION: Recheck all fasteners immediately after
a load is applied to the crossbars.
Regularly check screws are tight.
10