Whispbar K423W User manual

K423W
Fitting Kit
EN Fitting Instructions for Basic Carrier
DE Montageanleitung für Basisträgersystem
ES Instrucciones de montaje para el sistema
de transporte
FR Instructions de montage pour Basic Carrier
NO Monteringsanvisning for takstativ
PT Instruções de Montagem para sistema de
transporte.
RU Установочные Инструкции для
Поперечных Балок
x 4 x 8 x 12 x 2
x 8 x 8 x 4 x 4
Revision No: 11E 1

Fitting Kit K423W
x 2 x 2 x 2 x 2
x 4 x 4 x 4
2

Fitting Kit K423W
MAX kgs (lbs)
W/P WHD
Nissan
X-Trail Lowline, 5dr SUV 01-07 ZA 75 kgs (165 lbs) 75 kgs (165 lbs)
X-Trail, 5dr SUV 01-06 EU 75 kgs (165 lbs) 75 kgs (165 lbs)
X-Trail, 5dr SUV 04-04 CN 75 kgs (165 lbs) 75 kgs (165 lbs)
X-Trail, 5dr SUV 07-10 ZA 75 kgs (165 lbs) 75 kgs (165 lbs)
X-Trail, 5dr SUV 07-10 EU 75 kgs (165 lbs) 75 kgs (165 lbs)
X-Trail, 5dr SUV 07-10 CN 75 kgs (165 lbs) 75 kgs (165 lbs)
X-Trail, 5dr SUV 10-14 EU 75 kgs (165 lbs) 75 kgs (165 lbs)
X-Trail, 5dr SUV 10-14 ZA 75 kgs (165 lbs) 75 kgs (165 lbs)
X-Trail, 5dr SUV 10-Mar 14 NZ 75 kgs (165 lbs) 75 kgs (165 lbs)
X-Trail, 5dr SUV 10-Mar 14 AU 75 kgs (165 lbs) 75 kgs (165 lbs)
X-Trail, 5dr SUV Oct 01-Sep 07 NZ 75 kgs (165 lbs) 75 kgs (165 lbs)
X-Trail, 5dr SUV Oct 01-Sep 07 AU 75 kgs (165 lbs) 75 kgs (165 lbs)
X-Trail, 5dr SUV Oct 07-10 NZ 75 kgs (165 lbs) 75 kgs (165 lbs)
X-Trail, 5dr SUV Oct 07-10 AU 75 kgs (165 lbs) 75 kgs (165 lbs)
3

Fitting Kit K423W
X
A B C 1 2 3
X-Trail Lowline, 5dr SUV 01-07 (ZA) -140mm 590mm - 875mm 840mm -
-5 -1/2ths" 23 1/4ths" - 34 7/16ths" 33 1/16ths" -
X-Trail, 5dr SUV 01-06 (EU) -140mm 590mm - 875mm 840mm -
-5 -1/2ths" 23 1/4ths" - 34 7/16ths" 33 1/16ths" -
X-Trail, 5dr SUV 04-04 (CN) -140mm 590mm - 875mm 840mm -
-5 -1/2ths" 23 1/4ths" - 34 7/16ths" 33 1/16ths" -
X-Trail, 5dr SUV 07-10 (ZA) -30mm 720mm - 885mm 855mm -
-1 -3/16ths" 28 3/8ths" - 34 13/16ths" 33 11/16ths" -
X-Trail, 5dr SUV 07-10 (EU) -30mm 720mm - 885mm 855mm -
-1 -3/16ths" 28 3/8ths" - 34 13/16ths" 33 11/16ths" -
X-Trail, 5dr SUV 07-10 (CN) -30mm 720mm - 885mm 855mm -
-1 -3/16ths" 28 3/8ths" - 34 13/16ths" 33 11/16ths" -
X-Trail, 5dr SUV 10-14 (EU) -30mm 720mm - 885mm 855mm -
-1 -3/16ths" 28 3/8ths" - 34 13/16ths" 33 11/16ths" -
X-Trail, 5dr SUV 10-14 (ZA) -30mm 720mm - 885mm 855mm -
-1 -3/16ths" 28 3/8ths" - 34 13/16ths" 33 11/16ths" -
X-Trail, 5dr SUV 10-Mar 14 (NZ) -30mm 720mm - 885mm 855mm -
-1 -3/16ths" 28 3/8ths" - 34 13/16ths" 33 11/16ths" -
X-Trail, 5dr SUV 10-Mar 14 (AU) -30mm 720mm - 885mm 855mm -
-1 -3/16ths" 28 3/8ths" - 34 13/16ths" 33 11/16ths" -
X-Trail, 5dr SUV Oct 01-Sep 07 (NZ) -140mm 590mm - 875mm 840mm -
-5 -1/2ths" 23 1/4ths" - 34 7/16ths" 33 1/16ths" -
X-Trail, 5dr SUV Oct 01-Sep 07 (AU) -140mm 590mm - 875mm 840mm -
-5 -1/2ths" 23 1/4ths" - 34 7/16ths" 33 1/16ths" -
X-Trail, 5dr SUV Oct 07-10 (NZ) -30mm 720mm - 885mm 855mm -
-1 -3/16ths" 28 3/8ths" - 34 13/16ths" 33 11/16ths" -
X-Trail, 5dr SUV Oct 07-10 (AU) -30mm 720mm - 885mm 855mm -
-1 -3/16ths" 28 3/8ths" - 34 13/16ths" 33 11/16ths" -
4

Fitting Kit EN
K423W
First Time Installation
●Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
●This kit fits type A, B, C and D.
●These instructions show type A crossbar
fitted. They also apply to type B, C and D.
●Use keys to remove covers.
5

Fitting Kit EN
K423W
●Use hex screwdriver to reverse adjusting
screw 10 turns.
●Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment method.
●Ensure each end of the crossbar is
adjusted equally.
●Clamps onto flush roof rail. Pins locate on
inside of rail.
●Please check the front of this manual for
information relating specifically to your
vehicle.
●Set bars to length (revert to rear of these
instructions).
6

Fitting Kit EN
K423W
●Tighten adjusting screw to 3 Nm (2.2 ft lb)
hand tight.
●Remove plastic clamp block by gripping bar
leg with fingers and push firmly with
thumbs until clamp block drops out behind
leg.
●Remove both pins from each leg. Use
tapered end of spanner located inside left
hand cover to assist.
7

Fitting Kit EN
K423W
●Detach foot from leg. Store loose parts in a
safe place.
●Repeat for all legs.
●Foot Part Number:
X-Trail 07-10, 10-13
= 11-02-236A left
= 11-02-237A right
X-Trail 01-07
= 11-02-238A left
= 11-02-239A right
●Select four feet assemblies and match the
left and right assemblies to the left and
right roof rack legs.
●Using short capscrew and washer, secure
assembly onto leg (use Hex Screwdriver
supplied with crossbar to assist)
●Do not over tighten.
●Repeat for all legs.
8

Fitting Kit EN
K423W
●Use two M5 x 12 mm self tapping screws to
secure the assembly onto the leg.
●Do not over tighten.
●Open or remove fixed-point covers.
●From the kit select the mounting plates and
fit the M6 x 25mm countersunk bolts
through the spacer and tighten.
9

Fitting Kit EN
K423W
●Ensure edge of rail aligns with edge of slot.
●Apply protective strip as shown.
Trim if required.
●Use fixed-point cover to check spacer
height as shown.
10

Fitting Kit EN
K423W
●Place washer at base of spacer to adjust
height if required.
●Refit fixed-point cover.
●Repeat for all four positions.
●Fixed-point cover may require trimming to
accommodate load plate.
Fitment
●Place crossbar on vehicle.
●Ensure back edge of foot sits flush with the
back edge of vehicle roof rail.
11

Fitting Kit EN
K423W
●Place one hand on the leg and apply
downward pressure.
●Ensure the clamp engages correctly on
inside of roof rail.
●Slide clamp through opening in leg.
●Coach bolt length:
X-Trail 07-10, 10-13 = 35 mm (1 3/8")
X-Trail 01-07 = 30 mm (1 1/8")
●Thread the coach bolt through the clamp
and the leg.
12

Fitting Kit EN
K423W
●Tighten the plastic knob.
●Do not over tighten.
●Ensure the plastic knob is in the position
shown when fully tightened.
●Repeat for all four positions.
●Use keys to fit and lock covers
●Check crossbar is securely attached to the
vehicle.
13

Fitting Kit EN
K423W
CAUTION: Recheck all fasteners immediately after
a load is applied to the crossbars.
Regularly check screws are tight.
14

Fitting Kit EN
K423W
Maintenance
●Clean the car roof and surfaces of the
product that will be in contact with the car
roof.
●Follow the fitting instructions for fitting the
product to your vehicle. Make sure all steps
are carried out in order.
●Set crossbars a minimum distance of
700mm (27 1/2") apart where no other
distance is specified in the fitting
instructions. This is especially important
when carrying long loads.
●Check unit is securely attached whenever
you refit it to the vehicle. If the unit feels
loose, refer to the fitting instructions and
readjust.
●Some glass/panoramic roofs and radio
antennae may not be able to be used when
the product is fitted.
●Do not modify this product.
●Refer to the maximum permitted load
capacity specified in the fitting instructions.
Do not exceed the vehicle manufacturers
roof load rating if it is lower than the
maximum load capacity specified in the
fitting instructions.
●Loads should not overhang the sides of the
product and be evenly distributed with the
lowest possible centre of gravity.
●Long loads should be secured with non-
elastic straps to the front and rear of the
vehicle.
●Objects with pointed ends (e.g. ski poles)
should be carried with the pointed ends to
the rear of the vehicle.
●Remove all loose or removable objects
from the load prior to loading.
●Make sure all loads are securely fastened
with non-elastic straps. Check regularly
during longer journeys.
●A loaded roof rack system can alter the
performance of your vehicle. Be especially
aware of the effects of side winds,
changing of direction, and braking
performance. Avoid rapid acceleration and
deceleration. Drive carefully.
●Note that the total height of the vehicle
increases when upright loads are carried.
●Products should be locked during transport
if they have locks fitted.
15

Fitting Kit EN
K423W
●Check and replace worn out or defective
parts.
●Keep the product clean and maintained.
●Never drive into a car wash with the roof
rack system fitted.
●Lubricate locks and adjusting screws at
regular intervals.
●Remove the products from the vehicle
when not in use. Make sure all loose parts
are stored safely.
●Yakima Europe Coöperatief U.A.
Archimedesbaan 25
3439 ME Nieuwegein
The Netherlands
[phone]
www.whispbar.eu
www.whispbar.co.uk
●Yakima Products, Inc.
4101 Kruse Way,
Lake Oswego, OR 97035
USA
www.whispbar.com
www.whispbar.ca
16

Fitting Kit DE
K423W
Erstinstallation
●Komponenten aus der Verpackung
nehmen und überprüfen. Setzen Sie sich
mit Ihrem Händler in Verbindung, sollten
Teile fehlen oder beschädigt sein!
●Dieses Kit ist für die Typen A, B, C und D.
●Dargestellt ist der Querträger des Typs A.
Die Anweisungen gelten aber auch für die
Typen B, C und D!
●Abdeckungen mit Schlüsseln abnehmen.
17

Fitting Kit DE
K423W
●Innensechskantschlüssel benutzen und
Stellschraube mit 10 Umdrehungen lösen.
●Befestigungsschraube eindrücken und
Querträgerschenkel ausziehen. Siehe
Anweisungen für das Einstellen der
Querträger!
●Sicherstellen, dass beide Enden der
Querträger gleich lang eingestellt sind
(Maß 'x', s. Abb.).
●Wird an die bündige Dachreling geklemmt.
Stifte gehen in die Schiene.
●Finden Sie Informationen speziell für Ihr
Fahrzeug im der Vorderteil Teil dieser
Bedienungsanleitung.
●Beide Stangen auf Länge einstellen. (siehe
Rückseite dieser Anleitung)
18

Fitting Kit DE
K423W
●Stellschraube mit 3 Nm / 2.2 ft lb anziehen.
●Klemmblock nach hinten drücken und so
entfernen.
●Entfernen Sie beide Stifte aus jedem
Schenkel. Nutzen Sie als Hilfsmittel das
zugespitzte Ende des
Schraubenschlüssels, der sich unter der
linken Abdeckung befindet.
19

Fitting Kit DE
K423W
●Fuß vom Schenkel nehmen. Lose Teile
sicher aufbewahren!
●Montage bei allen Beinen wiederholen.
●Fuß Teileummer:
X-Trail 07-10, 10-13
= 11-02-236A links
= 11-02-237A rechts
X-Trail 2001-2007
= 11-02-238A links
= 11-02-239A rechts
●Vier Fußeinheiten auswählen (links und
rechts) und in die linken bzw. rechten
Gepäckträgerschenkel einsetzen.
●Befestigen Sie den Aufbau mit der kurzen
Kopfschraube und einer Unterlegschraube
am Fuß (verwenden Sie hierzu den mit
dem Querträger mitgelieferten
Sechskantschlüssel).
●Nicht zu fest anziehen!
●Montage bei allen Beinen wiederholen.
20