Whispbar K590W User manual

K590W
Fitting Kit
EN Fitting Instructions for Basic Carrier
x 2 x 2 x 2 x 2
x 1 x 1 x 1 x 1
Revision No: 5E 1

Fitting Kit K590W
MAX kgs (lbs)
W/P WHD
Alfa Romeo
Giulietta, 5dr Hatch 10-13 AU 50 kgs (110 lbs) 50 kgs (110 lbs)
Giulietta, 5dr Hatch 10-13 EU 50 kgs (110 lbs) 50 kgs (110 lbs)
Giulietta, 5dr Hatch 10-13 ZA 50 kgs (110 lbs) 50 kgs (110 lbs)
Giulietta, 5dr Hatch 10-13 NZ 50 kgs (110 lbs) 50 kgs (110 lbs)
Giulietta, 5dr Hatch 10-13 CN 50 kgs (110 lbs) 50 kgs (110 lbs)
Giulietta, 5dr Hatch 14-+ NZ 50 kgs (110 lbs) 50 kgs (110 lbs)
Giulietta, 5dr Hatch 14-+ AU 50 kgs (110 lbs) 50 kgs (110 lbs)
Giulietta, 5dr Hatch 14-+ EU 50 kgs (110 lbs) 50 kgs (110 lbs)
Giulietta, 5dr Hatch 14-+ ZA 50 kgs (110 lbs) 50 kgs (110 lbs)
Giulietta, 5dr Hatch 14-+ CN 50 kgs (110 lbs) 50 kgs (110 lbs)
2

Fitting Kit K590W
X
A B C 1 2 3
Giulietta, 5dr Hatch 10-13 (AU) -360mm 400mm - 805mm 775mm -
-14 -3/16ths" 15 3/4ths" - 31 11/16ths" 30 1/2ths" -
Giulietta, 5dr Hatch 10-13 (EU) -360mm 400mm - 805mm 775mm -
-14 -3/16ths" 15 3/4ths" - 31 11/16ths" 30 1/2ths" -
Giulietta, 5dr Hatch 10-13 (ZA) -360mm 400mm - 805mm 775mm -
-14 -3/16ths" 15 3/4ths" - 31 11/16ths" 30 1/2ths" -
Giulietta, 5dr Hatch 10-13 (NZ) -360mm 400mm - 805mm 775mm -
-14 -3/16ths" 15 3/4ths" - 31 11/16ths" 30 1/2ths" -
Giulietta, 5dr Hatch 10-13 (CN) -360mm 400mm - 805mm 775mm -
-14 -3/16ths" 15 3/4ths" - 31 11/16ths" 30 1/2ths" -
Giulietta, 5dr Hatch 14-+ (NZ) -365mm 400mm - 805mm 775mm -
-14 -3/8ths" 15 3/4ths" - 31 11/16ths" 30 1/2ths" -
Giulietta, 5dr Hatch 14-+ (AU) -365mm 400mm - 805mm 775mm -
-14 -3/8ths" 15 3/4ths" - 31 11/16ths" 30 1/2ths" -
Giulietta, 5dr Hatch 14-+ (EU) -365mm 400mm - 805mm 775mm -
-14 -3/8ths" 15 3/4ths" - 31 11/16ths" 30 1/2ths" -
Giulietta, 5dr Hatch 14-+ (ZA) -365mm 400mm - 805mm 775mm -
-14 -3/8ths" 15 3/4ths" - 31 11/16ths" 30 1/2ths" -
Giulietta, 5dr Hatch 14-+ (CN) -365mm 400mm - 805mm 775mm -
-14 -3/8ths" 15 3/4ths" - 31 11/16ths" 30 1/2ths" -
3

Fitting Kit EN
K590W
First Time Installation
●Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
●This kit fits type A, B, C and D.
●These instructions show type A crossbar
fitted. They also apply to type B, C and D.
NOTE: Clamp images in these instructions may
not be representative of the clamps in this kit
4

Fitting Kit EN
K590W
●Use keys to remove covers.
●Use hex screwdriver to reverse adjusting
screw 10 turns.
●Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment method.
●Ensure each end of the crossbar is
adjusted equally.
5

Fitting Kit EN
K590W
●Remove locking screw.
●Apply protective strip as shown.
Trim if required.
●It is important to put the clamps in the
correct position on the vehicle.
●Letters refer to the part numbers stamped
on clamps.
●Clamp Part Number:
A = 752A
B = 753A
6

Fitting Kit EN
K590W
●Attach clamp to each leg. NOTE; clamps
may have labels showing their positions on
the vehicle (For example; "Front Right").
●Refit locking screw so that it goes through
the hole in the clamp. Do not begin to
tighten the locking screw.
●Refer to the underside of the pad for the
part number.
7

Fitting Kit EN
K590W
●It is important to put the pads in the correct
position on the vehicle.
●Letters refer to the pad part numbers and
position.
●Pad Part Number:
A = 11-04-224
B = 11-04-225
C = 11-04-226
D = 11-04-227
●Fit rubber pads (supplied with fitting kit) to
foot. Pad may vary in shape to that shown.
●Make sure the pad fits into the holes
underneath the foot.
8

Fitting Kit EN
K590W
Fitment
●Place crossbar on vehicle. Minimum
recommended spacing between the bars is
700mm (27 1/2") (unless otherwise stated).
●Please check the front of this manual for
information relating specifically to your
vehicle.
●Locate vehicle's fixed points.
●Adjust the legs on the crossbar so that they
are positioned equally from the ends of the
crossbar, and the clamps engage firmly on
the body work of the vehicle.
●Clamps directly to edge of roof under the
doors, pin locates in hole on vehicle
●Tighten adjusting screw to 5 Nm (3.7 ft lb)
hand tight.
9

Fitting Kit EN
K590W
●Tighten locking screw on both legs evenly.
●Check crossbar is securely attached to the
vehicle.
●Use keys to fit and lock covers
10