Whispbar K603W User manual

K603W
Fitting Kit
EN Fitting Instructions for Basic Carrier
DMontageanleitung für Basisträgersystem
ES Instrucciones de montaje para el sistema de transporte.
FInstructions de montage pour Basic Carrier
NO Monteringsanvisning for takstativ
PT Instruções de Montagem para sistema de transporte.
RU Установочные Инструкции для Поперечных Балок
x 4 x 8 x 1 x 1
x 4 x 4 x 4 x 4
x 8 x 4
Revision No: 4C 1

Fitting Kit K603W
MAX kgs (lbs)
W/P WHD
Nissan
Navara D40 Double Cab, 4dr Truck 05-+ US 75 kgs (165 lbs) 75 kgs (165 lbs)
Navara D40 Double Cab, 4dr Ute 05-+ EU 75 kgs (165 lbs) 75 kgs (165 lbs)
Navara D40 Double Cab, 4dr Ute Dec 05-+ NZ 75 kgs (165 lbs) 75 kgs (165 lbs)
Navara D40 Double Cab, 4dr Ute Nov 05-+ AU 75 kgs (165 lbs) 75 kgs (165 lbs)
2

Fitting Kit EN
K603W
Items you will require:
●Tape measure
Pen
Cordless drill
Depth stop
Vacuum cleaner
Rust inhibitor
Small paint brush
Neutral cure silicon sealant
Rivet gun
Attention:
●Attaches with permanent mount blocks
riveted to roof. Bar can be removed.
Professional installation advised.
3

Fitting Kit EN
K603W
First Time Installation
●Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
●This kit fits type A, B, C and D.
●These instructions show type D crossbar
fitted. They also apply to type A, B and C.
●Use keys to remove covers.
4

Fitting Kit EN
K603W
●Remove Hex Key from right hand cover.
●Use hex screwdriver to reverse adjusting
screw 10 turns.
●Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment.
●Ensure each end of the crossbar is
adjusted equally.
5

Fitting Kit EN
K603W
●Adjust crossbar in or out to suit vehicle.
●Please check the rear of this manual for
information relating specifically to your
vehicle.
●Remove plastic clamp block by gripping bar
leg with fingers and push firmly with
thumbs until clamp block drops out behind
leg.
●Select plastic internal block (from fitting kit)
and insert into foot.
●Repeat for all legs.
6

Fitting Kit EN
K603W
●Tighten adjusting screw to 5 Nm (3.7 ft lb).
●Fit rubber pads (supplied with fitting kit) to
foot. Pad may vary in shape to that shown.
●Make sure the pad fits into the holes
underneath the foot.
●This setup is applicable for two crossbars
only.
●Recommended crossbar placement is as
shown.
7

Fitting Kit EN
K603W
●This setup is applicable for one crossbar
only.
●Recommended single crossbar placement
is above door pillar.
●Apply masking tape to vehicle roof in all
four positions.
●Position the permanent mount block so the
inner edge of the block is on the outer edge
of the ditch channel.
8

Fitting Kit EN
K603W
●With the drill, lightly mark both permanent
mount hole positions while holding the
mount firmly on roof.
●CAUTION: Maximum depth 7mm.
Use 7mm drillstop over supplied 4.9mm
drill bit.
Drill two outside holes at marked positions.
●Remove masking tape.
9

Fitting Kit EN
K603W
●Treat holes to prevent corrosion.
●Apply neutral cure silicon sealant in and
around drilled holes.
●Install rivets through permanent mount
blocks.
10