Whispbar K705W User manual

K705W
Fitting Kit
EN Fitting Instructions for Basic Carrier
x 2 x 2 x 1 x 1
x 1 x 1 x 2 x 2
Revision No: 4D 1

Fitting Kit K705W
x 2 x 2 x 1 x 1
x 1 x 1
2

Fitting Kit K705W
MAX kgs (lbs)
W/P WHD
BMW
5 Series E60, 4dr Sedan 03-09 NZ 60 kgs (132 lbs) 60 kgs (132 lbs)
5 Series E60, 4dr Sedan 03-09 AU 60 kgs (132 lbs) 60 kgs (132 lbs)
5 Series E60, 4dr Sedan 04-09 ZA 60 kgs (132 lbs) 60 kgs (132 lbs)
5 Series E60, 4dr Sedan 04-10 US 60 kgs (132 lbs) 60 kgs (132 lbs)
5 Series E60, 4dr Sedan 04-10 EU 60 kgs (132 lbs) 60 kgs (132 lbs)
5 Series E60, 4dr Sedan 04-10 CN 60 kgs (132 lbs) 60 kgs (132 lbs)
3

Fitting Kit K705W
X
A B C 1 2 3
5 Series E60, 4dr Sedan 03-09 (NZ) -250mm 455mm - 860mm 850mm -
-9 -13/16ths" 17 15/16ths" - 33 7/8ths" 33 7/16ths" -
5 Series E60, 4dr Sedan 03-09 (AU) -250mm 455mm - 860mm 850mm -
-9 -13/16ths" 17 15/16ths" - 33 7/8ths" 33 7/16ths" -
5 Series E60, 4dr Sedan 04-09 (ZA) -250mm 455mm - 865mm 850mm -
-9 -13/16ths" 17 15/16ths" - 34 1/16ths" 33 7/16ths" -
5 Series E60, 4dr Sedan 04-10 (US) -250mm 455mm - 860mm 850mm -
-9 -13/16ths" 17 15/16ths" - 33 7/8ths" 33 7/16ths" -
5 Series E60, 4dr Sedan 04-10 (EU) -250mm 455mm - 865mm 850mm -
-9 -13/16ths" 17 15/16ths" - 34 1/16ths" 33 7/16ths" -
5 Series E60, 4dr Sedan 04-10 (CN) -250mm 455mm - 865mm 850mm -
-9 -13/16ths" 17 15/16ths" - 34 1/16ths" 33 7/16ths" -
4

Fitting Kit EN
K705W
First Time Installation
●Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
●This kit fits type A, B, C and D.
●These instructions show type A crossbar
fitted. They also apply to type B, C and D.
NOTE: Clamp images in these instructions may
not be representative of the clamps in this kit
5

Fitting Kit EN
K705W
●Use keys to remove covers.
●Use hex screwdriver to reverse adjusting
screw 10 turns.
●Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment method.
●Ensure each end of the crossbar is
adjusted equally.
6

Fitting Kit EN
K705W
●Remove locking screw.
●Apply protective strip as shown.
Trim if required.
●A = Clear
B = Grey
●Letters refer to the part numbers stamped
on clamps.
●Clamp Part Number:
A = C021
B = C022
C = C023
D = C024
7

Fitting Kit EN
K705W
●Attach clamp to each leg. NOTE; clamps
may have labels showing their positions on
the vehicle (For example; "Front Right").
●Refit locking screw so that it goes through
the hole in the clamp. Do not begin to
tighten the locking screw.
●It is important to put the pads in the correct
position on the vehicle.
●Letters refer to the pad part numbers and
position.
●Pad Part Number:
A = 293A
B = 294A
8

Fitting Kit EN
K705W
●Fit rubber pads (supplied with fitting kit) to
foot. Pad may vary in shape to that shown.
●Make sure the pad fits into the holes
underneath the foot.
Fitment
●Place crossbar on vehicle. Minimum
recommended spacing between the bars is
700mm (27 1/2") (unless otherwise stated).
●Clamps directly to edge of roof under the
doors
●Please check the front of this manual for
information relating specifically to your
vehicle.
9

Fitting Kit EN
K705W
●Adjust the legs on the crossbar so that they
are positioned equally from the ends of the
crossbar, and the clamps engage firmly on
the body work of the vehicle.
●Tighten adjusting screw to 3 Nm (2.2 ft lb)
hand tight.
●Tighten locking screw on both legs evenly,
3 Nm (2.2 ft lb).
10