Whispbar K909W Operation and installation manual

K909W
Fitting Kit
EN Fitting Instructions for Basic Carrier
x 1 x 1 x 1 x 1
x 2 x 2 x 4 x 4
x 4
Revision No: 2B 1

Fitting Kit K909W
MAX kgs (lbs)
W/P WHD
Opel
Corsa, 3dr Hatch 15-+ EU 75 kgs (165 lbs) 75 kgs (165 lbs)
Corsa, 3dr Hatch 15-+ ZA 75 kgs (165 lbs) 75 kgs (165 lbs)
Corsa, 5dr Hatch 15-+ EU 75 kgs (165 lbs) 75 kgs (165 lbs)
Corsa, 5dr Hatch 15-+ ZA 75 kgs (165 lbs) 75 kgs (165 lbs)
Vauxhall
Corsa, 3dr Hatch 15-+ EU 75 kgs (165 lbs) 75 kgs (165 lbs)
Corsa, 5dr Hatch 15-+ EU 75 kgs (165 lbs) 75 kgs (165 lbs)
2

Fitting Kit K909W
X
A B C 1 2 3
Corsa, 3dr Hatch 15-+ (EU) -550mm 150mm - 863mm 760mm -
-21 -5/8ths" 5 7/8ths" - 34" 29 15/16ths" -
Corsa, 3dr Hatch 15-+ (ZA) -550mm 150mm - 863mm 760mm -
-21 -5/8ths" 5 7/8ths" - 34" 29 15/16ths" -
Corsa, 3dr Hatch 15-+ (EU) -550mm 150mm - 863mm 760mm -
-21 -5/8ths" 5 7/8ths" - 34" 29 15/16ths" -
Corsa, 5dr Hatch 15-+ (EU) -325mm 360mm - 863mm 770mm -
-12 -13/16ths" 14 3/16ths" - 34" 30 5/16ths" -
Corsa, 5dr Hatch 15-+ (ZA) -325mm 360mm - 863mm 770mm -
-12 -13/16ths" 14 3/16ths" - 34" 30 5/16ths" -
Corsa, 5dr Hatch 15-+ (EU) -325mm 360mm - 863mm 770mm -
-12 -13/16ths" 14 3/16ths" - 34" 30 5/16ths" -
3

Fitting Kit EN
K909W
First Time Installation
●Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
●This kit fits type A, B, C and D.
●These instructions show type A crossbar
fitted. They also apply to type B, C and D.
●Use keys to remove covers.
4

Fitting Kit EN
K909W
●Use hex screwdriver to reverse adjusting
screw 10 turns.
●Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment method.
●Ensure each end of the crossbar is
adjusted equally.
●Set bars to length (revert to rear of these
instructions).
●Please check the front of this manual for
information relating specifically to your
vehicle.
5

Fitting Kit EN
K909W
●Tighten adjusting screw to 5 Nm (3.7 ft lb)
hand tight.
●Remove plastic clamp block by gripping bar
leg with fingers and push firmly with
thumbs until clamp block drops out behind
leg.
●Select plastic internal block (from fitting kit)
and insert into foot.
●Repeat for all legs.
6

Fitting Kit EN
K909W
Fitment
●Open or remove fixed-point covers.
●It is important to put the clamps in the
correct position on the vehicle.
●Letters refer to the part numbers stamped
on clamps.
●Clamp Part Number:
A = 096A
B = 095A
●Hook small claw into rear of the clamping
block
●Hook large claw into front of the clamping
block
7

Fitting Kit EN
K909W
●Refer to the underside of the pad for the
part number.
●Letters refer to the pad part numbers and
position.
●It is important to put the pads in the correct
position on the vehicle.
●Pad Part Number:
A = 11-04-225
B = 11-04-224
C = 11-04-222
D = 11-04-223
●Ensure internal clamp sits upright.
●Fit pad carefully over fixed point and clamp
screw.
8

Fitting Kit EN
K909W
●Mount crossbars over clamps.
●Repeat for all legs.
●Place washer over clamp thread as shown.
●Ensure that tab is inserted into clamp
block.
●Tighten the plastic knob. The side with the
nut showing should be facing up.
9

Fitting Kit EN
K909W
●Ensure the plastic knob is in the position
shown when fully tightened.
●Repeat for all four positions.
●Check crossbar is securely attached to the
vehicle.
●Use keys to fit and lock covers
CAUTION: Recheck all fasteners immediately after
a load is applied to the crossbars.
Regularly check screws are tight.
10