Whitmor Modern Industrial Entryway Tower 6764-10131 User manual

Page 1
6764-10131 Modern Industrial Entryway Tower ©2019 Whitmor, Inc.
Tools Needed:
Phillips screwdriver & hammer
are needed for wall mounting
A2 ea
Side frames
B2 ea
Wire shelves
E2 ea
Middle vertical
tubes
F2 ea
Upper vertical
tubes
H2 ea
Horizontal posts
M8 ea
Hooks
L4 ea
Feet
N1 ea
Hex
wrench
O1 ea
Safety
bracket
P1 ea
Wall
screw
Q1 ea
Wall
anchor
J6 ea
Medium hex screws
K6 ea
Short hex
screws
I20 ea
Long hex
screws
G1 ea
Top
C2 ea
Horizontal
supports
D1 ea
Upper
horizontal tube
STEP 1: Attach two horizontal supports (C) to the bottom side of
the top (G) using six medium hex screws (J). Tighten with hex
wrench (N). Include the safety bracket (O) in the middle between
horizontal support (C) and medium hex screw (J) as illustrated.
STEP 2: Assemble two wire shelves (B) to two side
frames (A) using eight long hex screws (I). Tighten with
hex wrench (N).
NOTE: When
assembling the
top make sure
safety bracket
(O) is facing
the back.
STEP 3: Attach the assembled top onto the side frames (A)
using four long hex screws (I). Tighten with hex wrench (N).
Back View:
J
J
J
J
J
J
O
N
C
CG
A
A
B
B
L
L
L
L
I
I
I
I
I
I
I
I
I
NNOTE: Correct orientation of the wire
shelves is the thinner wire on top.
G
N
I
I
I
I
I
STEP 4: Attach two middle
vertical tubes (E) to the
assembled unit using two short
hex screws (K). Tighten with hex
wrench (N).
K
K
K
N
E
E

Printed in VietnamPage 2
8680 Swinnea Road • Suite 103 • Southaven, MS • 38671
NEED HELP? For help with assembly, or if you are missing a part,
please call Whitmor’s Consumer Care Team, 1-888-944-8667 between
8 a.m. and 4:30 p.m. (Central Standard Time) Monday through Friday.
Or email: [e-mail]. Visit us online at www.whitmor.com
Rev#0 8.23.19
Part Reference
A
B
C
D
E
F
G
H
I
F10728
F10729
F10730
F10731
F10732
F10733
F10734
F10735
F10577
Part Reference
J
K
L
M
N
O
P
Q
F10578
F10736
F10737
F10738
F10579
F10739
F10740
F10741
STEP 5: Attach two upper vertical
tubes (F) to the assembled unit
using two short hex screws (K).
Tighten with hex wrench (N).
STEP 6: Install upper horizontal tube
(D) onto the upper vertical tubes (F)
using two short hex screws (K). Tighten
with hex wrench (N).
STEP 8: Install the hooks (M)
onto the horizontal posts.
STEP 9: To install the safety
bracket, mark the spot on the
wall with a pencil.
For drywall installation: Take
a nail-set, awl, or nail and with
a hammer tap a “pilot hole” into
the wall. DO NOT make the
hole wider than the anchor.
Place the anchor (Q) over the
hole and firmly tap it in until it is
flush with the wall.
For stud installation: discard
wall anchors.
Attach the safety bracket (O) to
the wall using a wall screw (P)
and screwdriver (not included).
STEP 7: Install two horizontal posts
(H) to the upper vertical tubes (F)
using eight long hex screws (I).
Tighten with hex wrench (N).
K
K
N
K
K
K
N
I
N
H
H
H
I
I
F
M
M
F
Back View:
Side View:
Q
Q P
P
O
O
D
I
I
K
M
M
M