Whittier Wood Furniture 1141AFGSPe User manual

P.O. Box 2827
Eugene, OR 97402 USA
Production Code:
VN 03/14
Model #
1141AFGSPe;
1141AFCAFe
Pacific Blanket
Dresser
AFGSP = Glazed Spice finish
AFCAF = Caffè finish
Assembly Instructions
Congratulations!
This fine piece of furniture will make a gorgeous addition to
your home. For the best results, read the Assembly
Instructions before you begin your project.
IMPORTANT NOTES:
For normal household use only. Not recommended for commercial use.
Do not climb, sit or stand on this piece of furniture.
Do not overload the drawers.
Unload items before you move this unit.
Before you load or move this unit, tighten all screws and supports.
Before you begin your project, completely read the Assembly
Instructions.
Store this item: 1- in its box; 2- in a dry place; 3- in temperatures that
range from 40°F to 90°F (not on a cold and possibly damp cement
floor).
Periodically inspect your furniture for any loose glue joints, screws or
any other problem that might affect the stability of your furniture.
Tighten or repair as needed.
This assembly requires two people.
WARNING
Serious or fatal crushing injuries can occur from furniture tip-over. Use of
tip-over restraints may only reduce but not eliminate the risk of tip-over.
To help prevent tip-over:
Place heaviest items in the bottom drawers.
Unless specifically designed to accommodate, do not set TVs or other
heavy objects on top of this product.
Never allow children to climb or hang on drawers, doors or shelves.
Never open more than one drawer at a time.
Warning: At least one tipping restraint kit was included with your piece of
Whittier Wood Furniture. When you receive your furniture, be sure to find
and properly install the tipping restraint(s). If you cannot locate the
restraint(s), please contact us immediately for replacement.
Notice to California Customers
California Prop 65 requires consumer goods to be labeled if any one of
850+ different chemicals or substances, including wood dust, is present
even in trace amounts. Drilling, sawing, sanding or machining wood
products generates wood dust, a substance known to the State of
California to cause cancer. Warning: This product contains a chemical
or substance known to the State of California to cause cancer, birth
defects or other reproductive harm. California Health and Safety Code
Section 25249.6
DESIGN SUBJECT TO CHANGE WITHOUT NOTICE.
CALL US FIRST! Do not return this item to the store
Service Policy: We will replace any part that is defective,
missing or damaged during assembly. For a replacement
part, directly contact Whittier Wood Products customer
service department by phone, fax, mail or email.
Hours: Our friendly customer service staff can be reached
Monday-Friday 7:00 a.m. to 5:00 p.m. (Pacific Time). You
may leave a message 24 hours a day, seven days a week.
To Order: Provide the finish and furniture model number
(upper portion of this page), the part letter, production
code, quantity needed, reason for replacement and your
full name, address and telephone number.
Parts ship from our Eugene, Oregon factory within one or
two business days from the time we receive your request.
Please allow five to ten business days for delivery.
800-653-3336 •Outside the U.S. or Canada: 541-687-0213 • Fax: [phone]
www.whittierwood.com • P.O. Box 2827 • Eugene, Oregon 97402, U.S.A.

1141AFGSPe; 1141AFCAFe Pacific Blanket Dresser
Parts List
1141AFGSPe_1141AFCAFe—Page 2 —03/14
Please identify the parts and check that quantities received match those on this list.
If you need to replace a part, refer to the following letter and part name.
Part
Description
Quantity
A
Top Assembly (attached)
1
Bb
Case
1
C
Large Left Drawer (inserted)
1
D
Large Right Drawer (inserted)
1
E
Medium Left Drawer (inserted)
2
F
Medium Right Drawer (inserted)
2
G
Center Drawer with secret storage (inserted)
1
H
Small Left Drawer (inserted)
1
I
Small Right Drawer (inserted)
1
J
Large Drawer Face (installed)
2
K
Medium Drawer Face (installed)
4
L
Small Drawer Face (installed)
2
M
Center Drawer Face (installed)
1
N
Knob (attached)
3
O
Handle (attached)
6
Q
Drawer Slides (pre-installed sets)
9
R
#6 x 1/2" Philtruss Screw (inserted)
54
S
#6 x 3/4" Philtruss Screw (inserted)
54
Vb
Hinged Drawer Stop (attached)
1
W
Small Adjustable Glide (installed)
4
ZC
#8 x 1-1/4" Pan Head Screw (inserted)
11
ZE
#8 x 1-5/8" Black Screw (inserted)
2
ZF
#8 x 1-1/4" Black Screw (inserted)
38
ZH
#8 x 2" Black Screw (inserted)
2

1141AFGSPe; 1141AFCAFe Pacific Blanket Dresser
Parts List
1141AFGSPe_1141AFCAFe—Page 3 —03/14
Part
Description
Quantity
ZI
Hex Bumper (attached)
2
ZJ
Velvet back of sleeper 50 x 20mm (attached)
1
ZK
#6 x 5/8" Undercut Screw (inserted)
2
ZM
M4 x 10mm Insert Nut (inserted)
4
ZO
#8 x 1-1/8" Lo-Profile Screw (inserted)
10
ZP
1/4" x 20mm Insert Nut (inserted)
4
ZR
#8 x 1-3/8" Lo-Profile Screw (inserted)
9
ZS
Adjustable Glide with Hex Nut (installed)
1
ZT
Assembled Foot (attached)
1
ZU
5/16" x 3/4" Insert Nut (inserted)
1
ZV
#8 x 7/8" Black Lo-Profile Screw (inserted)
48
ZW
#8 x 1-5/8" Machine Screw Tuscan (installed)
15
TS
Furniture Tipping Restraint (attached)
1 set

1141AFGSPe; 1141AFCAFe Pacific Blanket Dresser
Assembly Instructions
1141AFGSPe_1141AFCAFe—Page 4 —03/14
Tool Required: Phillips Screwdriver, Pencil.
1. There is a secret storage area in the center drawer (G). To access this storage, open the top
right medium drawer (F). Reach in until you find the Hinged Drawer Stop (Vb) that is attached to
the bottom right side of the Center Drawer (G). Pull the Hinged Drawer Stop forward and then
pull the center drawer (G) out far enough so you can access the concealed storage space.
To close the drawer, just push it shut. See Figure 1.
2. Place the unit at its final destination. Rotate the Small Adjustable Glides (W) found at the
corners of the unit and the Adjustable Glide with Hex Nut (ZS) at the bottom of the Assembled
Foot (ZT) until the unit is level. See Figure 2.
Continued on Page 5
Fig. 2
W
W
ZT
ZS
Fig. 1
G
Vb
G
F

1141AFGSPe; 1141AFCAFe Pacific Blanket Dresser
Assembly Instructions
1141AFGSPe_1141AFCAFe—Page 5 —03/14
Furniture Tipping Restraint Instructions
Before you begin this assembly, identify each part and make sure the quantities received match what is on this
list. If you need to replace a part, contact Whittier Wood Furniture customer service and refer to the following
list for its name and letter code.
Part
Description
Quantity
A
Cam Buckle and Short Strap (installed)
1
B
Plastic Bracket (installed)
1
C
1" x 1000mm Long Strap (installed)
1
D
#8 x 3" Pan Head Screw
2
E
#10 x 1" Oval Head Screw (inserted)
1
F
Washer
1
If you have a stone or tile floor or do not wish to drive screws into the corner of the baseboard
and floor see the instruction included inside the tipping restraint kit for an alternate
installation.
3. Decide where you want to place the piece of furniture in your room. Mark the baseboard with a
pencil mark directly behind the location where the tipping restraint is attached to your item.
Move the item away from the wall far enough to allow you to access the spot where the
baseboard meets the floor. Position the straps and Plastic Bracket (B) as shown in Figures 3
and 3a with the angled corners of the Plastic Bracket (B) firmly placed against the seam of the
baseboard and floor. Attach by driving #8 x 3" Pan Head Screws (D) through the holes in the
Plastic Bracket (B) into the seam below the baseboard where it meets the floor. See Figures 3
and 3a.
Fig. 3
D
x 2
Fig. 3a
Wall
Floor
D
Floor
Baseboard

1141AFGSPe; 1141AFCAFe Pacific Blanket Dresser
Assembly Instructions
1141AFGSPe_1141AFCAFe—Page 6 —03/14
4. Move the item back into position against the wall and reach underneath the piece of furniture to
grasp the loop in the free end of the strap. Pull the free end of the strap until portion between
the Cam Buckle (A) and the back apron of the item is tight. See Figures 4 and 4a. If you need
to move the piece of furniture reach beneath and locate the buckle which connects the two
sections of the strap and depress the release lever, then pull on the section of strap that is
between the buckle and the back apron of the furniture until there is enough slack to allow you
to pull the item away from the wall.
Fig. 4a
Fig. 4
C
Wall
Floor