Whittier Wood Furniture McKenzie Cal-King 1333AFGAC User manual

Production Code:
04/10
VN
P.O. Box 2827
Eugene, OR 97402 USA
Service Policy: We will replace any part that is
defective, missing or damaged during assembly.
Please contact Whittier Wood Products customer
service department directly by phone, fax, mail or
email for a replacement part.
To Order: Provide the furniture model number (upper
left corner of this page), the part letter, production
code, quantity needed, reason for replacement, your
full name, address and telephone number.
Parts ship from our Eugene, Oregon factory within one
or two business days from the time we receive your
request. Please allow five to ten business days for delivery.
CALL US FIRST! Do not return this item to the store.
800-653-3336 • Outside the U.S. or Canada: 541-687-0213 • Fax: [phone]
www.whittierwood.com • P.O. Box 2827 • Eugene, Oregon 97402, U.S.A.
Hours: Our friendly customer service staff can be
reached Monday-Friday 7:00 a.m. to 5:00 p.m. (Pacific
Time). You may leave a message 24 hours a day,
seven days a week.
Before you load or move this item, check to make
sure all screws and supports are tight.
This assembly requires two people.
.
Before you begin your project, completely read the
Assembly Instructions.
For normal household use only. Not recommended
for commercial use.
Remove items before you move this unit.
Do not overload the drawers in this unit.
Store this item: 1- in its box; 2- in a dry place; 3- in
temperatures that range from 40° F to 90° F (not on
a cold and possibly damp cement floor).
Periodically inspect your furniture for any loose
glue joints, screws or any other problem that might
affect the stability of your furniture. Tighten or
repair as needed.
IMPORTANT NOTES:
Assembly Instructions
Glazed Antique Cherry finish
Model #
McKenzie Cal-King
Storage Bed
1333AFGAC
Congratulations!
This fine piece of furniture will make a gorgeous
addition to your home. For the best results, read the
Assembly Instructions before you begin your project.

1333AFGAC McKenzie Cal-King Storage Bed — Parts List
Page 2 — 1333AFGAC — 04/10
Please identify the parts and check that quantities received match what is on this list.
If you need to replace a part, refer to the following letter and item name.
1336AFGAC (x1) Headboard/Footboard kit
A — Headboard — Qty.1
B — Footboard — Qty.1
C — Trestle Without T-Nuts — Qty.4
D — Trestle With T-Nuts — Qty.8
F — 1/4" x 1-3/4" Hex Bolt
— Qty. 16
G — 1/4" x 2-1/2" Hex Bolt
— Qty. 16
H — Washer
— Qty. 32
E — #8 x 1-1/4" Black Screw
— Qty. 48 (12 inserted)
T — #8 x 2" Black Screw
— Qty. 6
ZU — 1/4" T-Nut
— Qty. 32 (inserted)
ZQ — Left Bracket
— Qty. 4 (attached)
ZR — Right Bracket
— Qty. 4 (attached)
ZP — #8 x 1" Black Screw
— Qty. 32 (inserted)
ZV — #8 x 20mm Pan Head
Screw — Qty. 60 (inserted)
ZX — #8 x 1-5/8" Black Screw
— Qty. 4 (inserted)
U — Foot Assembly
— Qty. 2
ZY — Foot Bracket
— Qty. 2 (attached)
V — Leveler Bracket
— Qty. 2 (installed)
W — Adjustable Glide
— Qty. 2 (installed)
R — Long Center Deckboard
— Qty.1
S — Short Center Deckboard
— Qty.1
1335AFGAC (x2) Pedestal kit
N — #8 x 1-1/2" Machine
Screw — Qty. 3
O — Knob — Qty. 3
I — Pedestal Kit — Qty.1
P — Deckboard — Qty.1
J — Drawer Box
— Qty. 3 (assembled)
L — Drawer Face
— Qty. 3 (attached)
Q — Drawer Slides
— Qty. 3 (attached sets)
T — #8 x 2" Black Screw
— Qty. 16 (inserted)
ZQ — Left Bracket
— Qty. 2 (attached)
ZR — Right Bracket
— Qty. 2 (attached)
ZP — #8 x 1" Black Screw
— Qty. 16 (inserted)
ZW — #6 x 1/2" Undercut
Screw — Qty. 36 (inserted)
Y — #8 x 7/8" Lo-Profile
Screw — Qty. 24 (inserted)
E — #8 x 1-1/4" Black
Screw — Qty. 30 (inserted)
ZX — #8 x 1-5/8" Black
Screw — Qty. 12 (inserted)

McKenzie Cal-King Bed 1333AFGAC
Assembly Instructions
Page 3 — 1333AFGAC — 04/10
Tools Required: Phillips screwdriver, 7/16" wrench, tape measure
This Assembly Requires Two People
Fig. 2
I
I
74"
Fig. 1
S
R
Shipping Straps
Remove the Trestles (C and D), Long Center Deckboard (R) and Short Center Deckboard (S)
from the back of the Headboard (A) as seen in Figure 1 and place them off to the side.
1.
Place both Pedestals (I) approximately 74" apart as shown in Figure 2.2.

Page 4 — 1333AFGAC — 04/10
Remove the Drawers (J) from the Pedestal Kits (I). To remove the drawers, pull up on the left
side of the Drawer Release Lever while pushing down on the right Drawer Release Lever.
See Figure 3a. Note where each drawer came from to ensure correct installation. Positions are
marked on drawer bottoms.
3.
Fig. 3
Fig. 3a
Drawer Release Lever
Place four Trestles with T-Nuts (D) between the Pedestals (I) and insert and hand-tighten
1/4 x 1-3/4" Bolts (F) and Washers (H) as shown in Figure 4a. When installing the Trestles (D),
make sure the T-nuts face out as shown in Figure 4.
NOTE: Do not tighten the bolts with a wrench until the final assembly in
step 10 is completed. Hand-tighten only.
4.
Fig. 4a
Trestle with T-Nuts (D)
F x 16 H x 16
H
F
Fig. 4
T-Nuts face out
D
D
D
D
I
I

Page 5 — 1333AFGAC — 04/10
5. Rotate the Pedestal Assembly upside down so the plywood deckboards are on the floor.
Fig. 6a
G x 16 H x 16
Fig. 6
D
D
D
D
C
CC
C
6. Position the remaining Trestles (C and D) on the Pedestal Assembly. Face the Trestles with
T-Nuts (D) toward the ends of the Assembly from the center of the assembly as shown in Figure 6.
Insert and hand-tighten the 1/4" x 2-1/2" Hex Bolts (G) and Washers (H). See Figures 6 and 6a.
Fig. 5
R
o
t
a
t
e
P
e
d
e
s
t
a
l
A
s
s
e
m
b
l
y
u
p
s
i
d
e
d
o
w
n
s
o
t
h
a
t
t
h
e
p
l
y
w
o
o
d
D
e
c
k
b
o
a
r
d
s
a
r
e
o
n
t
h
e
f
l
o
o
r
.
NOTE: Do not tighten the bolts with a wrench until the final assembly in
step 10 is completed. Hand-tighten only.
T-nuts face out

Page 6 — 1333AFGAC — 04/10
Rotate the Pedestal Assembly to its original position.
Fig. 7
Fig. 7a
D
D
CC
T x 6
7.
8.
On each inner Pair of Trestles (C & D), place a Foot Assembly (U) between the two middle
trestles as shown in Figure 7. Attach with three #8 x 2" Black Screws (T), making sure the screws
penetrate both the Trestle and Foot. See Figure 7a.
U
Fig. 8
R
o
t
a
t
e
P
e
d
e
s
t
a
l
A
s
s
e
m
b
l
y
t
o
i
t
s
o
r
i
g
i
n
a
l
p
o
s
i
t
i
o
n
.
V
W
T

Page 7 — 1333AFGAC — 04/10
Fig. 10
A
Attach the Footboard (B) to the Pedestal Assembly as in Figure 9. Align the brackets as shown
in Figure 9a and slide the Pedestal Assembly down on to the Footboard (B).
9.
Fig. 9a
Fig. 9
B
Adjust the Glides (W) on the Foot Assemblies (U) so the Glides just touch the floor.11.
Fig. 11
Adjustable Glide (W)
Leveler Bracket (V)
Attach the Headboard (A) to the Pedestal Assembly as in the previous step.
NOTE: Now use a wrench and tighten all of the bolts on the trestles.
10.

Page 8 — 1333AFGAC — 04/10
Place the Deckboards (P) as shown in Figure 13 and secure with #8 x 1-1/4" Black Screws (E).
There should be a small gap between each deckboard.
13.
Fig. 13
E x 24
P
P
12.
Fig. 12
To make sure the bed is square, measure the distance between opposing corners. If one of the
measurements is larger, tap on a footboard leg until the measurement is equal. See Figure 12.

Page 9 — 1333AFGAC — 04/10
15.
Fig. 14
E x 12
14.
R
S
Place the Long Center Deckboard (R) and Short Center Deckboard (S) as shown in Figure 14
and secure with #8 x 1-1/4" Black Screws (E). If you need to readjust the center feet, remove
the Long Center Deckboard (R), adjust the glides, and then reattach the deckboard.
Place three additional
#8 x 1-1/4" Black Screws (E)
along the seam between
the Deckboards (R) and (S).
See Figure 14a.
Fig. 14a
Drawer positions are marked on the bottoms. Carefully align drawer slides into the cabinet and
gently push them back to their original positions.
Sleep well, and enjoy!