Whittier Wood Furniture Stayton 3450AFCAFa User manual

P.O. Box 2827
Eugene, OR 97402 USA
Production Code:
VN 05/13
Model #
3450AFCAFa
Stayton Chair Side Table
AFCAF = Caffè finish
Assembly Instructions
Congratulations!
This fine piece of furniture will make a gorgeous addition to
your home. For the best results, read the Assembly
Instructions before you begin your project.
IMPORTANT NOTES:
For normal household use only. Not recommended for
commercial use.
Do not climb, sit or stand on this piece of furniture.
Unload items before you move this unit.
Do not overload the shelf.
Before you load or move this unit, tighten all screws and
supports.
Before you begin your project, completely read the
Assembly Instructions.
Store this item: 1- in its box; 2- in a dry place; 3- in
temperatures that range from 40°F to 90°F (not on a cold
and possibly damp cement floor).
Periodically inspect your furniture for any loose glue
joints, screws or any other problem that might affect the
stability of your furniture. Tighten or repair as needed.
DESIGN SUBJECT TO CHANGE WITHOUT NOTICE.
CALL US FIRST! Do not return this item to the store
Service Policy: We will replace any part that is defective,
missing or damaged during assembly. For a replacement
part, directly contact Whittier Wood Products customer
service department by phone, fax, mail or email.
Hours: Our friendly customer service staff can be reached
Monday-Friday 7:00 a.m. to 5:00 p.m. (Pacific Time). You
may leave a message 24 hours a day, seven days a week.
To Order: Provide the finish and furniture model number
(upper portion of this page), the part letter, production
code, quantity needed, reason for replacement and your
full name, address and telephone number.
Parts ship from our Eugene, Oregon factory within one or
two business days from the time we receive your request.
Please allow five to ten business days for delivery.
800-653-3336 •Outside the U.S. or Canada: 541-687-0213 • Fax: [phone]
www.whittierwood.com • P.O. Box 2827 • Eugene, Oregon 97402, U.S.A.

3450AFCAFa Stayton Chair Side Table
Parts List
3450AFCAFa —Page 2 —05/13
Please identify the parts and check that quantities received match those on this list.
If you need to replace a part, refer to the following letter and part name.
Part
Description
Quantity
Aa
Top Assembly (attached)
1
B
Leg
4
C
Shelf Assembly
1
D
#8 x 1-1/4" Pan Head Screw
24
(20 inserted)
E
#8 Washer (inserted)
16
F
5/16" Flat Washer
4
G
3/8" x 1" Insert Nut (inserted)
4
H
3/8" x 2-1/2" Hex Bolt
4
I
1/4" x 20mm Insert Nut (inserted)
4
J
Wood Dowel (inserted)
4
K
#8 x 20mm Pan Head Screw (inserted)
12
L
Adjustable Angle Bracket (attached)
4
M
Adjustable Glide (installed)
4

3450AFCAFa Stayton Chair Side Table
Assembly Instructions
3450AFCAFa —Page 3 —05/13
Tools Required: Phillips Screwdriver, 9/16" or Adjustable Wrench, Rubber Mallet or Padded
Hammer
1. Turn the Top Assembly (Aa) upside-down on a clean, protected surface. Place two Legs (B) at
the back of the Top Assembly (Aa), making sure the drilled corners of the legs face toward the
Corner Blocks. Attach with 5/16" Flat Washers (F) and 3/8" x 2-1/2" Hex Bolts (H). See Figures
1 and 1a.
2. Rotate the Top and Leg assembly so that is sets on the back legs. Turn the Shelf Assembly (C)
bottom-side-down and place the dowels into the dowel holes in the Legs. See Figure 2.
Fig. 2
C
Fig. 1
B
B
Fig. 1a
Aa
F
H
x 2
x 2
H
F

3450AFCAFa Stayton Chair Side Table
Assembly Instructions
3450AFCAFa —Page 4 —05/13
3. Using the dowels as guides, place the remaining Legs (B) in the remaining two corners making
sure the drilled corners of the Legs face toward the Corner Blocks. See Figures 3 and 3a.
4. Attach the legs to the Top Assembly with 5/16" Flat Washers (F) and 3/8" x 2-1/2" Hex Bolts (H).
See Figures 4 and 4a.
B
Fig. 3
Fig. 3a
B
Fig. 4
Fig. 4a
F
H
x 2
x 2
F
H

3450AFCAFa Stayton Chair Side Table
Assembly Instructions
3450AFCAFa —Page 5 —05/13
5. Turn the unit onto its top and using the pocket holes as guides, secure the Shelf Assembly (C)
to the Legs (B) with four #8 x 1-1/4" Pan Head Screws (D). See Figures 5 and 5a.
6. Turn the table upright. See Figure 6.
7. Place the table at its final destination. To level the table, rotate the Adjustable Glides (M) found
on the bottoms of the legs. See Figure 6.
Fig. 6
M
M
Fig. 5
D
x 4
D
Fig. 5a