Whittier Wood Furniture McKenzie 2319AFGACc User manual

P.O. Box 2827
Eugene, OR 97402 USA
Production Code:
VN 04/14
Model #
2319AFGACc;
2319AFCAFc
McKenzie King
Mantel Storage Bed
AFGAC = Glazed Antique Cherry finish
AFCAF = Caffè finish
Assembly Instructions
Congratulations!
This fine piece of furniture will make a gorgeous
addition to your home. For the best results, read the
Assembly Instructions before you begin your project.
IMPORTANT NOTES:
For normal household use only. Not recommended for commercial use.
Remove items before you move this unit.
Do not overload the drawers.
Before you load or move this unit, tighten all screws and supports.
Before you begin your project, completely read the Assembly
Instructions.
Store this item: 1- in its box; 2- in a dry place; 3- in temperatures that
range from 40°F to 90°F (not on a cold and possibly damp cement
floor).
Periodically inspect your furniture for any loose glue joints, screws or
any other problem that might affect the stability of your furniture.
Tighten or repair as needed.
This assembly requires two people.
WARNING
Notice to California Customers
California Prop 65 requires consumer goods to be labeled if any one of
850+ different chemicals or substances, including wood dust, is present
even in trace amounts. Drilling, sawing, sanding or machining wood
products generates wood dust, a substance known to the State of
California to cause cancer. Warning: This product contains a chemical
or substance known to the State of California to cause cancer, birth
defects or other reproductive harm. California Health and Safety Code
Section 25249.6
DESIGN SUBJECT TO CHANGE WITHOUT NOTICE.
CALL US FIRST! Do not return this item to the store.
Service Policy: We will replace any part that is defective,
missing or damaged during assembly. For a replacement
part, contact Whittier Wood Products customer service
department by phone, fax, mail or email.
Hours: Our friendly customer service staff can be reached
Monday-Friday 7:00 a.m. to 5:00 p.m. (Pacific Time). You
may leave a message 24 hours a day, seven days a week.
To Order: Provide the finish and furniture model number
(upper portion of this page), the part letter, production
code, quantity needed, reason for replacement and your
full name, address and telephone number.
Parts ship from our Eugene, Oregon factory within one or
two business days from the time we receive your request.
Please allow five to ten business days for delivery
800-653-3336 •Outside the U.S. or Canada: 541-687-0213 • Fax: [phone]
www.whittierwood.com • P.O. Box 2827 • Eugene, Oregon 97402, U.S.A.

2319AFGACc; 2319AFCAFc McKenzie King Mantel Storage Bed
Parts List
2319AFGACc_2319AFCAFc —Page 2 —04/14
Please identify the parts and check that quantities received match those on this list.
If you need to replace a part, refer to the following letter and part name.
1318AFGACe; 1318AFCAFe Pedestal Kit (x2)
Part
Description
Quantity
E
#8 x 1-1/4" Black Screw (inserted)
30
Id
Pedestal Kit
1
J
Small Drawer Box (assembled)
2
Kd
Large Drawer Box (assembled)
1
L
Small Drawer Face (attached)
2
Md
Large Drawer Face (attached)
1
Ne
#8 x 1-1/2" Machine Screw Tuscan (installed)
3
O
Knob (attached)
3
Pd
Deckboard
1
Q
Drawer Slides (installed)
3 sets
T
#8 x 2" Black Screw (inserted)
12
YD
#6 x 1/2" Philtruss Screw (inserted)
18
YE
#6 x 3/4" Philtruss Screw (inserted)
18
YL
#8 x 7/8" Black Lo-Profile Screw (inserted)
20
ZP
#8 x 1" Black Screw (inserted)
16
ZQ
Left Bracket (attached)
2
ZR
Right Bracket (attached)
2
ZX
#8 x 1-5/8" Black Screw (inserted)
16

2319AFGACc; 2319AFCAFc McKenzie King Mantel Storage Bed
Parts List
2319AFGACc_2319AFCAFc —Page 3 —04/14
2320AFGACa; 2320AFCAFa
K. Mantel Headboard/Footboard Kit (x1)
Part
Description
Quantity
Aa
Headboard Assembly
1
B
Footboard Assembly
1
Rb
Center Deckboard
1
YH
Top Assembly
1
YI
#8 x 1-1/4" Pan Head Screw
2
YJ
Cam Connector (inserted)
2
YK
Cam Housing
2
ZP
#8 x 1" Black Screw (inserted)
32
ZQ
Left Bed Bracket (attached)
4
ZR
Right Bed Bracket (attached)
4
ZX
#8 x 1-5/8" Black Screw (inserted)
4

2319AFGACc; 2319AFCAFc McKenzie King Mantel Storage Bed
Parts List
2319AFGACc_2319AFCAFc —Page 4 —04/14
2321Wc
K. Mantel Assembly Kit (x1)
Part
Description
Quantity
Da
Trestle With T-Nuts
7
E
#8 x 1-1/4" Black Screw
45
(9 inserted)
F
1/4" x 1-3/4" Hex Bolt
26
H
1/4" Flat Washer
26
Ua
Assembled Foot
3
W
Adjustable Glide (installed)
3
YD
#6 x 1/2" Philtruss Screw
8
YG
90oBracket
2
YM
#10 x 3/4" Pan Head Screw (inserted)
12
ZU
1/4" T-Nut (inserted)
28
ZY
Foot Bracket (attached)
3

2319AFGACc; 2319AFCAFc McKenzie King Mantel Storage Bed
Assembly Instructions
This assembly requires two people.
2319AFGACc_2319AFCAFc —Page 5 —04/14
Tools Required: Phillips screwdriver, 7/16" open end or box end wrench and Tape measure
1. Remove the Center Deckboard (Rb) from the back of the Headboard (Aa) and place to the side.
See Figure 1.
2. NOTE: READ CAM INSTRUCTIONS NOW BEFORE YOU BEGIN THE FOLLOWING STEP.
Insert Cam Housings (YK) into the two pre-drilled holes on the Headboard Assembly (Aa) as
shown in Figure 2. Lower Top Assembly (YH) so that the Cam Connectors (YJ) fit into the
housings (YK) tighten the cam housings as indicated in the Cam-lock System instructions. See
Figures 2 and 2a.
Fig. 1
Shipping Straps
Rb
Aa
Fig. 2
Aa
YH
YK
x 2
YK
YK
Fig. 2a
YK
YJ

2319AFGACc; 2319AFCAFc McKenzie King Mantel Storage Bed
Assembly Instructions
This assembly requires two people.
2319AFGACc_2319AFCAFc —Page 6 —04/14
3. Attach the Top Assembly (YH) to the Headboard Assembly (Aa) by inserting two #8x1-1/4" Pan
Head Screws (YI) into the predrilled holes in the block that is attached to the Headboard
Assembly (Aa). See Figures 3 and 3a.
4. Place both Pedestals (Id) approximately 79" apart as shown in Figure 4.
Fig. 3
YI
x 2
Fig. 3a
YI
Fig. 4
79"
Id
Id

2319AFGACc; 2319AFCAFc McKenzie King Mantel Storage Bed
Assembly Instructions
This assembly requires two people.
2319AFGACc_2319AFCAFc —Page 7 —04/14
5. To attach the Footboard (B) to the Pedestal Assembly (Id), align the Brackets and slide the
Pedestal Assembly down on to the Footboard (B). See Figures 5 and 5a.
6. Repeat step five for the left side.
Fig. 6
Id
Fig. 6a
Fig. 5
Id
B
Fig. 5a

2319AFGACc; 2319AFCAFc McKenzie King Mantel Storage Bed
Assembly Instructions
This assembly requires two people.
2319AFGACc_2319AFCAFc —Page 8 —04/14
7. Align the Brackets on both sides and slide the Pedestal/Footboard assembly down on to the
Headboard (Aa). See Figure 7.
Fig. 7
Aa

2319AFGACc; 2319AFCAFc McKenzie King Mantel Storage Bed
Assembly Instructions
This assembly requires two people.
2319AFGACc_2319AFCAFc —Page 9 —04/14
8. Open the drawers. Face the Footboard and stand in between the first and second braces.
Place a Trestle with T-Nuts (Da) on the outside surfaces of the first upper left and right braces
so that the T-Nuts (ZU) sit near the top. See Figure 5a. Line up the upper edges of the trestle
and braces so they are nearly flush. Insert two 1/4" x 1-3/4" Hex Bolts (F) and Washers (H) and
tighten. Repeat for the second upper brace.
Place a Trestle with T-Nuts (Da) on the outside surface of the second lower brace so that
the T-Nuts (ZU) sit near the bottom. Line up the bottom edges of the trestle and braces so they
are nearly flush. Insert two 1/4" x 1-3/4" Hex Bolts (F) and Washers (H) and tighten.
See Figures 8 and 8a.
Fig. 8
Da
First brace
Second brace
Da
F
H
F
H
x 6
x 6
Footboard
Headboard removed for illustration purposes.
Fig. 8a
H
F
Brace
Da

2319AFGACc; 2319AFCAFc McKenzie King Mantel Storage Bed
Assembly Instructions
This assembly requires two people.
2319AFGACc_2319AFCAFc —Page 10 —04/14
9. Face the Headboard and stand in between the third and fourth braces. Place a Trestle with
T-Nuts (Da) on the outside surfaces of the third upper left and right braces so the T-nuts sit
near the top. See Figures 6 and 6a. Line up the upper edges of the trestle and braces so they
are nearly flush. Insert two 1/4" x 1-3/4" Hex Bolts (F) and Washers (H) and tighten.
Place a Trestle with T-Nuts (Da) on the outside surface of the third left and right lower braces
so that the T-nuts sit near the bottom. Line up the bottom edges of the trestle and braces so
they are nearly flush. Insert two 1/4" x 1-3/4" Hex Bolts (F) and Washers (H) and tighten.
See Figures 9 and 9a.
Repeat for the fourth braces.
Fig. 9
Fourth brace
Third brace
Da
F
F
H
x 8
x 8
Fig. 9a
H
F
Brace
H
Trestle with T-Nuts (Da)
Da