Whittier Wood Furniture 1326AFGAC User manual

Production Code:
06/10
VN
P.O. Box 2827
Eugene, OR 97402 USA
Service Policy: We will replace any part that is
defective, missing or damaged during assembly.
Please contact Whittier Wood Products customer
service department directly by phone, fax, mail or
email for a replacement part.
To Order: Designate the finish, provide the furniture model
number (upper left corner of this page), the part letter,
production code, quantity needed, reason for replacement,
your full name, address and telephone number.
Parts ship from our Eugene, Oregon factory within one
or two business days from the time we receive your
request. Please allow five to ten business days for delivery.
CALL US FIRST! Do not return this item to the store.
800-653-3336 • Outside the U.S. or Canada: 541-687-0213 • Fax: [phone]
www.whittierwood.com • P.O. Box 2827 • Eugene, Oregon 97402, U.S.A.
Hours: Our friendly customer service staff can be
reached Monday-Friday 7:00 a.m. to 5:00 p.m.
(Pacific Time). You may leave a message 24 hours
a day, seven days a week.
Before you load or move this item, check to make
sure all screws and supports are tight.
This assembly requires two people.
.
Before you begin your project, completely read the
Assembly Instructions.
For normal household use only. Not recommended
for commercial use.
Remove items before you move this unit.
Do not overload the drawers in this unit.
Store this item: 1- in its box; 2- in a dry place; 3- in
temperatures that range from 40° F to 90° F (not on
a cold and possibly damp cement floor).
Periodically inspect your furniture for any loose
glue joints, screws or any other problem that might
affect the stability of your furniture. Tighten or
repair as needed.
IMPORTANT NOTES:
Assembly Instructions
Model #
McKenzie King Storage Bed
1326AFGAC; 1326AFCAF
Congratulations!
This fine piece of furniture will make a gorgeous
addition to your home. For the best results, read the
Assembly Instructions before you begin your project.
AFGAC = Glazed Antique Cherry finish
AFCAF = Caffè finish

1326AFGAC; 1326AFCAF McKenzie
King Storage Bed — Parts List
Page 2 — 1326AFGAC_1326AFCAF — 06/10
Please identify the parts and check that quantities received match what is on this list.
If you need to replace a part, refer to the following letter and item name.
1318AFGACa; 1318AFGAFa (x2) Pedestal Kit
N — #8 x 1-1/2" Machine Screw
— Qty. 3
O — Knob — Qty. 3
I — Pedestal Kit — Qty.1
P — Deckboard — Qty.1
J — Small Drawer Box
— Qty. 2 (assembled)
K — Large Drawer Box
— Qty. 1 (assembled)
L — Small Drawer Face
— Qty. 2 (attached)
M — Large Drawer Face
— Qty. 1 (attached)
Q — Drawer Slides — Qty. 3
(attached sets)
T — #8 x 2" Black Screw
— Qty. 16 (inserted)
ZQ — Left Bracket
— Qty. 2 (attached)
ZR — Right Bracket
— Qty. 2 (attached)
ZP — #8 x 1" Black Screw
— Qty. 16 (inserted)
ZW — #6 x 1/2" Undercut
Screw — Qty. 30 (inserted)
Y — #8 x 7/8" Lo-Profile
Screw — Qty. 20 (inserted)
E — #8 x 1-1/4" Black
Screw — Qty. 30 (inserted)
ZX — #8 x 1-5/8" Black
Screw — Qty. 12 (inserted)
1327AFGAC; 1327AFCAF (x1) Headboard Kit
A — Headboard — Qty.1
B — Footboard — Qty.1
C — Trestle Without T-Nuts — Qty.4
D — Trestle With T-Nuts — Qty.8
F — 1/4" x 1-3/4" Hex Bolt
— Qty. 16
G — 1/4" x 2-1/2" Hex Bolt
— Qty. 16
H — Washer
— Qty. 32
E — #8 x 1-1/4" Black Screw
— Qty. 48 (12 inserted)
T — #8 x 2" Black Screw
— Qty. 6
ZU — 1/4" T-Nut
— Qty. 32 (inserted)
ZQ — Left Bracket
— Qty. 4 (attached)
ZR — Right Bracket
— Qty. 4 (attached)
ZP — #8 x 1" Black Screw
— Qty. 32 (inserted)
ZV — #8 x 20mm Pan Head
Screw — Qty. 60 (inserted)
ZX — #8 x 1-5/8" Black Screw
— Qty. 4 (inserted)
U — Foot Assembly
— Qty. 2
ZY — Foot Bracket
— Qty. 2 (attached)
V — Leveler Bracket
— Qty. 2 (installed)
W — Adjustable Glide
— Qty. 2 (installed)
R — Center Deckboard — Qty.1

McKenzie King Storage Bed
Assembly Instructions
Page 3 — 1326AFGAC_1326CAF — 06/10
Tools Required:
This Assembly Requires Two People
Phillips screwdriver, 7/16" open end or box end wrench and tape measure
Fig. 1
Fig. 2
I
I
79"
Shipping Straps
A
R
D
C
Remove the Trestles (C and D) and the Center Deckboard (R) from the back of the Headboard
and remove the Foot Assemblies (U) from the Footboard as seen in Figures 1 and 1b and place
them off to the side.
1.
Place both Pedestals (I) approximately 79" apart as shown in Figure 2.2.
Fig. 1a
U
B

Page 4 — 1326AFGAC_1326CAF — 06/10
Remove the Drawers (J & K) from the Pedestal Kits (I). To remove the drawers, pull up on
the left side of the Drawer Release Lever while pushing down on the right Drawer Release Lever.
See Figure 3a. Note where each drawer came from to ensure correct installation. Positions are
marked on drawer bottoms.
3.
Fig. 3
Fig. 3a
Drawer Release Lever
Place four Trestles with T-Nuts (D) between the Pedestals (I) and insert and hand-tighten
1/4 x 1-3/4" Bolts (F) and Washers (H) as shown in Figure 4a. When installing the Trestles (D),
make sure the T-nuts face out as shown in Figure 4.
NOTE: Do not tighten the bolts with a wrench until the final assembly in
step 10 is completed. Hand-tighten only.
4.
Fig. 4a
Trestle with T-Nuts (D)
F x 16 H x 16
H
F
Fig. 4
T-Nuts face out
D
D
D
D
I
I

Rotate the Pedestal Assembly up-side down so the Plywood Deckboards are
on the floor. This step requires two people.
5.
6.
Fig. 6
Fig. 7
Fig. 7a
Fig. 6a
T-Nuts face out
G x 16 H x 16
C
C
C
C
D
DD
D
C
C
DD
T x 6
U
Page 5 — 1326AFGAC_1326AFCAF — 06/10
Position the remaining Trestles (C and D) on the Pedestal Assembly. Face the Trestles with
T-Nuts (D) toward the ends of the Assembly from the center as shown in Figure 6. Insert and
hand-tighten the 1/4" x 2-1/2" Hex Bolts (G) and Washers (H). See Figures 6 and 6a.
7. On each inner pair of Trestles (C and D), place a Foot Assembly (U) between the two middle
trestles as shown in Figure 7. Attach each Trestle with three #8 x 2" Black Screws (T) as shown
in Figure 7a.
T

11.
Fig. 10
A
Page 6 — 1326AFGAC_1326AFCAF — 06/10
Rotate the Pedestal Assembly so the deckboards face up. This step requires two people.8.
Fig. 9
Fig. 9a
B
Attach the Footboard (B) to the Pedestal Assembly as in Figure 9. Align the brackets as shown
in Figure 9a and slide the Pedestal Assembly down on to the Footboard (B).
9.
Rotate the Glides (W) on the Foot Assemblies (U) so they just touch the floor.
Attach the Headboard (A) to the Pedestal Assembly as in the previous step. NOTE: Now use a
wrench and tighten all of the bolts on the trestles.
10.

Page 7 — 1326AFGAC_1326AFCAF — 06/10
Fig. 12
Place the Deckboards (P) as shown in Figure 13 and secure them with #8 x 1-1/4" Black Screws (E).
There should be a small gap between each deckboard.
13.
Fig. 13
E x 24
P
P
12. To make sure the bed is square, measure the distance between opposing corners. If one of the
measurements is larger, tap on a footboard leg until the measurement is equal. See Figure 12.

Page 8 — 1326AFGAC_1326AFCAF — 06/10
15.
Fig. 14
R
E x 12
Place the Center Deckboard (R) as shown in Fig. 14 and secure with #8 x 1-1/4" Black Screws (E).
If at some time you need to adjust the center feet, remove the center deckboard, adjust the glides
and then reattach the deckboard.
14.
Positions are marked on the drawer bottoms. Carefully align drawer slides into the pedestal and
gently push them back to their original positions. Sleep well, and enjoy!