Whittier Wood Furniture McKenzie 3500AFGACc User manual

P.O. Box 2827
Eugene, OR 97402 USA
Production Code:
VN 07/14
Model #
3500AFGACc;
3500AFCAFc
McKenzie Chair
Side Table
AFGAC = Glazed Antique Cherry finish
AFCAF = Caffè finish
Assembly Instructions
Congratulations!
This fine piece of furniture will make a gorgeous addition to
your home. For the best results, read the Assembly
Instructions before you begin your project.
IMPORTANT NOTES:
For normal household use only. Not recommended for commercial use.
Do not climb, sit or stand on this piece of furniture.
Unload items before you move this unit.
Do not overload the drawer or shelf.
Before you load or move this unit, tighten all screws and supports.
Before you begin your project, completely read the Assembly
Instructions.
Store this item: 1- in its box; 2- in a dry place; 3- in temperatures that
range from 40°F to 90°F (not on a cold and possibly damp cement
floor).
Periodically inspect your furniture for any loose glue joints, screws or
any other problem that might affect the stability of your furniture.
Tighten or repair as needed.
WARNING
Notice to California Customers
California Prop 65 requires consumer goods to be labeled if any one of
850+ different chemicals or substances, including wood dust, is present
even in trace amounts. Drilling, sawing, sanding or machining wood
products generates wood dust, a substance known to the State of
California to cause cancer. Warning: This product contains a chemical
or substance known to the State of California to cause cancer, birth
defects or other reproductive harm. California Health and Safety Code
Section 25249.6
DESIGN SUBJECT TO CHANGE WITHOUT NOTICE.
CALL US FIRST! Do not return this item to the store
Service Policy: We will replace any part that is defective,
missing or damaged during assembly. For a replacement
part, directly contact Whittier Wood Products customer
service department by phone, fax, mail or email.
Hours: Our friendly customer service staff can be reached
Monday-Friday 7:00 a.m. to 5:00 p.m. (Pacific Time). You
may leave a message 24 hours a day, seven days a week.
To Order: Provide the finish and furniture model number
(upper portion of this page), the part letter, production
code, quantity needed, reason for replacement and your
full name, address and telephone number.
Parts ship from our Eugene, Oregon factory within one or
two business days from the time we receive your request.
Please allow five to ten business days for delivery.
800-653-3336 •Outside the U.S. or Canada: 541-687-0213 • Fax: [phone]
www.whittierwood.com • P.O. Box 2827 • Eugene, Oregon 97402, U.S.A.

3500AFGACc; 3500AFCAFc McKenzie Chair Side Table
Parts List
3500AFGACc_3500AFCAFc —Page 2 —07/14
Please identify the parts and check that quantities received match those on this list.
If you need to replace a part, refer to the following letter and part name.
Part
Description
Quantity
Ac
Case Assembly
1
Bc
Top Assembly (attached)
1
C
Shelf Assembly
1
D
Leg
4
F
Drawer (inserted)
1
I
Drawer Face (installed)
1
L
20" Drawer Slides (pre-installed set)
1
N
#6 x 3/4" Philtruss Screw (inserted)
6
O
#6 x 1/2" Philtruss Screw (inserted)
6
P
Knob (attached)
1
Qb
#8 x 1-1/2" Machine Screw Tuscan (installed)
1
S
Adjustable Glide (installed)
4
T
#8 x 1-1/4" Pan Head Screw
48
(44 inserted)
Ub
#8 x 7/8" Black Lo-Profile Screw (inserted)
4
V
Wood Dowel (inserted)
4
W
3/8" x 1" Insert Nut (inserted)
8
X
5/16" Flat Washer
8
Y
3/8" x 2-1/2" Hex Bolt
8
ZA
1/4" x 20mm Insert Nut (inserted)
4
ZB
#8 x 1-3/8" Lo-Profile Screw (inserted)
2
ZC
#10 x 2" Pan Head Screw (inserted)
6
ZD
#8 Washer (inserted)
6
ZE
Top Support (attached)
2

3500AFGACc; 3500AFCAFc McKenzie Chair Side Table
Assembly Instructions
3500AFGACc_3500AFCAFc —Page 3 —07/14
Tools Required: Phillips Screwdriver, 9/16" or Adjustable Wrench
1. Remove the Drawers (F) from the Case (Ac). To remove the drawers, pull up on the left side of
the Drawer Release Lever while pushing down on the right Drawer Release Lever. See Figure
1a. Note where each drawer came from to ensure correct installation.
2. Turn the unit upside down on a clean, protected surface. Place two Legs (D) at the front corners
of the Case (Ac) as shown in Figure 2. Face the drilled corners of the legs toward the Corner
Blocks. Insert two 3/8" x 2-1/2" Hex Bolts (Y) with two Flat Washers (X) through the Corner
Blocks and into the legs and securely fasten. See Figures 2 and 2a.
Fig. 2
X
Y
x 4
x 4
X
Y
Fig. 2a
X
Y
D
Ac
Fig. 1
Drawer Release Lever
Fig. 1a

3500AFGACc; 3500AFCAFc McKenzie Chair Side Table
Assembly Instructions
3500AFGACc_3500AFCAFc —Page 4 —07/14
3. Using the dowels as guides, insert the dowels in the Shelf (C) into the holes in the Legs (D). See
Figure 3. While holding the shelf stable, place a Leg (D) against the Case and Shelf so that the
Insert Nut aligns with the Corner Block and insert the Dowel in the Shelf into the hole in the leg.
Insert two 3/8" x 2-1/2" Hex Bolts (Y) with two Flat Washers (X) through the corner blocks and
into the leg and securely fasten. See Figures 3 and 3a. Repeat for the final leg.
4. Using the pocket drilled holes as guides, secure the Shelf with four #8 x 1-1/4" Pan Head
Screws (T). See Figures 4 and 4a.
Fig. 3
C
Fig. 3a
X
Y
x 4
x 4
Ac
D
Y
X
Fig. 4
T
x 4
T
T
Fig. 4a
T

3500AFGACc; 3500AFCAFc McKenzie Chair Side Table
Assembly Instructions
3500AFGACc_3500AFCAFc —Page 5 —07/14
5. Turn the table upright and insert the Drawer.
6. Place the table at its final destination. To level the table, rotate the Adjustable Glide (S) found at
the bottom of each leg. See Figure 5.
Fig. 5
S
S