Whittier Wood Furniture Stayton 3456AFCAFa User manual

P.O. Box 2827
Eugene, OR 97402 USA
Production Code:
VN 04/14
Model #
3456AFCAFa
Stayton Cocktail
Table
AFCAF = Caffè finish
Assembly Instructions
Congratulations!
This fine piece of furniture will make a gorgeous addition to
your home. For the best results, read the Assembly
Instructions before you begin your project.
IMPORTANT NOTES:
For normal household use only. Not recommended for commercial use.
Do not climb, sit or stand on this piece of furniture.
Unload items before you move this unit.
Do not overload the drawer or shelf.
Before you load or move this unit, tighten all screws and supports.
Before you begin your project, completely read the Assembly
Instructions.
Store this item: 1- in its box; 2- in a dry place; 3- in temperatures that
range from 40°F to 90°F (not on a cold and possibly damp cement
floor).
Periodically inspect your furniture for any loose glue joints, screws or
any other problem that might affect the stability of your furniture.
Tighten or repair as needed.
This assembly requires two people.
WARNING
Notice to California Customers
California Prop 65 requires consumer goods to be labeled if any one of
850+ different chemicals or substances, including wood dust, is present
even in trace amounts. Drilling, sawing, sanding or machining wood
products generates wood dust, a substance known to the State of
California to cause cancer. Warning: This product contains a chemical
or substance known to the State of California to cause cancer, birth
defects or other reproductive harm. California Health and Safety Code
Section 25249.6
DESIGN SUBJECT TO CHANGE WITHOUT NOTICE.
CALL US FIRST! Do not return this item to the store
Service Policy: We will replace any part that is defective,
missing or damaged during assembly. For a replacement
part, directly contact Whittier Wood Products customer
service department by phone, fax, mail or email.
Hours: Our friendly customer service staff can be reached
Monday-Friday 7:00 a.m. to 5:00 p.m. (Pacific Time). You
may leave a message 24 hours a day, seven days a week.
To Order: Provide the finish and furniture model number
(upper portion of this page), the part letter, production
code, quantity needed, reason for replacement and your
full name, address and telephone number.
Parts ship from our Eugene, Oregon factory within one or
two business days from the time we receive your request.
Please allow five to ten business days for delivery.
800-653-3336 •Outside the U.S. or Canada: 541-687-0213 • Fax: [phone]
www.whittierwood.com • P.O. Box 2827 • Eugene, Oregon 97402, U.S.A.

3456AFCAFa Stayton Cocktail Table
Parts List
3456AFCAFa —Page 2 —04/14
Please identify the parts and check that quantities received match those on this list.
If you need to replace a part, refer to the following letter and part name.
Part
Description
Quantity
A
Top Assembly (attached)
1
B
Left Front/Right Back Leg
2
C
Right Front/Left Back Leg
2
D
Shelf Assembly
1
E
Drawer Box (inserted)
1
F
Drawer Face (installed)
1
G
PVC Wheel (installed)
4
H
Drawer Slides (pre-installed sets)
1
I
Axle Pin (inserted)
4
J
#6 x 3/4" Philtruss Screw (inserted)
6
K
#6 x 1/2" Philtruss Screw (inserted)
6
M
#8 x 1-1/4" Pan Head Screw
34
(30 inserted)
Na
#8 x 1-1/2" Machine Screw Tuscan (installed)
4
O
#8 Washer (inserted)
23
P
5/16" Flat Washer
4
Q
3/8" x 1" Insert Nut (inserted)
4
R
3/8" x 2-1/2" Hex Bolt
4
S
4 x 10mm Insert Nut (inserted)
4
T
Pull (installed)
2
U
Wood Dowel (inserted)
4
W
Adjustable Angle Bracket (attached)
3
X
#8 x 7/8" Black Lo-Profile Screw (inserted)
6
Y
#10 x 3/4" Pan Head Screw (inserted)
9

3456AFCAFa Stayton Cocktail Table
Assembly Instructions
3456AFCAFa —Page 3 —04/14
Tools Required: Phillips Screwdriver, 9/16" or Adjustable Wrench, Rubber Mallet or Padded
Hammer
1. Remove the Drawer (E) from the Top Assembly (A). To remove the drawer, pull up on the left
side of the Drawer Release Lever while pushing down on the right Drawer Release Lever. See
Figure 1a.
2. Turn the Top Assembly (A) upside-down on a clean, protected surface. Place a Left Front/Right
Back Leg (B) and a Right Front/Left Back Leg (C) at the back of the Top Assembly (A), making
sure the drilled corners of the legs face toward the Corner Blocks. It is important the sides of the
legs exposing the wheel face the drawer opening of the unit. Attach with 5/16" Flat Washers (P)
and 3/8" x 2-1/2" Hex Bolts (R). See Figures 2 and 2a.
Fig. 1
Drawer Release Lever
Fig. 1a
Fig. 2
C
B
Fig. 2a
A
P
R
x 2
x 2
R
P

3456AFCAFa Stayton Cocktail Table
Assembly Instructions
3456AFCAFa —Page 4 —04/14
3. Rotate the Top and Leg assembly so that is sets on the back legs. Turn the Shelf Assembly (D)
bottom-side-down and place the dowels into the dowel holes in the Legs. See Figure 3.
4. Using the dowels as guides, place the remaining Left Front/Right Back Leg (B) and Right
Front/Left Back Leg (C) in the remaining two corners making sure the drilled corners of the Legs
face toward the Corner Blocks. It is important the side of the leg exposing the wheel face toward
the back of the unit. See Figure 4.
Fig. 4
Fig. 4a
B
C
Fig. 3
D

3456AFCAFa Stayton Cocktail Table
Assembly Instructions
3456AFCAFa —Page 5 —04/14
5. Attach the legs to the Top Assembly with 5/16" Flat Washers (P) and 3/8" x 2-1/2" Hex Bolts (R)
See Figures 5 and 5a.
6. Turn the unit onto its top and using the pocket holes as guides, secure the Shelf Assembly (D)
to the Legs (B and C) with four #8 x 1-1/4" Pan Head Screws (M). See Figures 6 and 6a.
Fig. 6
M
x 4
Fig. 6a
M
Fig. 5
Fig. 5a
P
R
x 2
x 2
P
R

3456AFCAFa Stayton Cocktail Table
Assembly Instructions
3456AFCAFa —Page 6 —04/14
7. Turn the table upright and insert the Drawer. See Figure 7.
8. The wheels allow the table to easily move away from or toward your seating.
Fig. 7
Fig. 8a
Fig. 8