Whittier Wood Furniture Stayton Media 3460AUF User manual

P.O. Box 2827
Eugene, OR 97402 USA
Production Code:
VN 04/13
Stayton Media
Tables
Assembly Instructions
Model #
Congratulations!
This fine piece of furniture will make a gorgeous addition to
your home. For the best results, read the Assembly
Instructions and Finishing Hints before you begin your
project.
IMPORTANT NOTES:
For normal household use only. Not recommended for
commercial use.
Do not climb, sit or stand on this piece of furniture.
Unload items before you move this unit.
Do not overload the drawer or shelves.
Before you load or move this unit, tighten all screws and
supports.
Before you begin your project, completely read the
Assembly Instructions and Finishing Hints.
Store this item: 1- in its box; 2- in a dry place; 3- in
temperatures that range from 40°F to 90°F (not on a cold
and possibly damp cement floor).
Periodically inspect your furniture for any loose glue
joints, screws or any other problem that might affect the
stability of your furniture. Tighten or repair as needed.
WARNING
Serious or fatal crushing injuries can occur from
furniture tip-over. To help prevent tip-over:
Place heaviest items in the bottom drawers.
Unless specifically designed to accommodate, do not
set TVs or other heavy objects on top of this product.
Never allow children to climb or hang on drawers, doors
or shelves.
Never open more than one drawer at a time.
Use of tip-over restraints may only reduce but not
eliminate the risk of tip-over.
DESIGN SUBJECT TO CHANGE WITHOUT NOTICE.
CALL US FIRST! Do not return this item to the store
Service Policy: We will replace any part that is defective,
missing or damaged during assembly. For a replacement
part, directly contact Whittier Wood Products customer
service department by phone, fax, mail or email.
Hours: Our friendly customer service staff can be reached
Monday-Friday 7:00 a.m. to 5:00 p.m. (Pacific Time). You
may leave a message 24 hours a day, seven days a week.
To Order: Provide the furniture model number (upper
portion of this page), the part letter, production code,
quantity needed, reason for replacement and your full
name, address and telephone number.
Parts ship from our Eugene, Oregon factory within one or
two business days from the time we receive your request.
Please allow five to ten business days for delivery.
800-653-3336 •Outside the U.S. or Canada: 541-687-0213 • Fax: [phone]
www.whittierwood.com • P.O. Box 2827 • Eugene, Oregon 97402, U.S.A.
3462AUF
Stayton Media
Center
3460AUF
Stayton Media
Console

3460AUF Stayton Media Console;
3462AUF Stayton Media Center
Parts List
3460AUF_3462AUF —Page 2 —04/13
Please identify the parts and check that quantities received match those on this list.
If you need to replace a part, refer to the following letter and part name.
Part
Description
Quantity
3460AUF
3462AUF
A
Top Assembly (attached)
1
1
B
Leg
4
4
C
Lower Shelf Assembly
1
1
D
Upper Shelf Assembly
1
1
E
Back Assembly
1
1
F
Drawer Box (inserted)
1
1
G
Drawer Face (installed)
1
1
H
Drawer Slides (pre-installed sets)
1
1
I
#6 x 3/4" Philtruss Screw (inserted)
4
6
J
#6 x 1/2" Philtruss Screw (inserted)
4
6
K
#6 x 5/8" Philtruss Screw
6
6
L
#8 x 1" Lo-Profile Screw (inserted)
6
6
M
#8 x 1-1/4" Pan Head Screw
42
(34 inserted)
45
(37 inserted)
N
#8 x 1-1/2" Machine Screw (installed)
4
4
O
#8 Washer (inserted)
18
21
P
5/16" Flat Washer
4
4
Q
3/8" x 1" Insert Nut (inserted)
4
4
R
3/8" x 2-1/2" Hex Bolt
4
4
S
1/4" x 20mm Insert Nut (inserted)
4
4
T
Pull (installed)
2
2
U
Wood Dowel (inserted)
8
8
V
Adjustable Glide (installed)
4
4
TR
Furniture Tipping Restraint
2 sets
2 sets
3462 shown in the illustrations.

3460AUF Stayton Media Console;
3462AUF Stayton Media Center
Assembly Instructions
3460AUF_3462AUF —Page 3 —04/13
Tools Required: Phillips Screwdriver, 9/16" or Adjustable Wrench, Rubber Mallet or Padded
Hammer
1. Remove the Drawer (F) from the Top Assembly (A). To remove the drawer, pull up on the left
side of the Drawer Release Lever while pushing down on the right Drawer Release Lever. See
Figure 1a.
2. Turn the Top Assembly (A) upside-down on a clean, protected surface. Place two Legs (B) at
the back of the Top Assembly (A), making sure the drilled corners of the legs face toward the
Corner Blocks. Attach with 5/16" Flat Washers (P) and 3/8" x 2-1/2" Hex Bolts (R). See Figures
2 and 2a.
Fig. 1
Drawer Release Lever
Fig. 1a
Fig. 2
B
B
Fig. 2a
A
P
R
x 2
x 2
R
P

3460AUF Stayton Media Console;
3462AUF Stayton Media Center
Assembly Instructions
3460AUF_3462AUF —Page 4 —04/13
3. Rotate the Top and Leg assembly so that is sets on the back legs. Turn the Lower Shelf
Assembly (C) and the Upper Shelf Assembly (D) bottom-side-down and place the dowels into
the dowel holes in the Legs. See Figure 3.
4. Using the dowels as guides, place the remaining Legs (B) in the remaining two corners making
sure the drilled corners of the Legs face toward the Corner Blocks. See Figures 4 and 4a.
Fig. 4
Fig. 4a
Fig. 3
C
D

3460AUF Stayton Media Console;
3462AUF Stayton Media Center
Assembly Instructions
3460AUF_3462AUF —Page 5 —04/13
5. Attach the legs to the Top Assembly with 5/16" Flat Washers (P) and 3/8" x 2-1/2" Hex Bolts (R)
See Figures 5 and 5a.
6. Turn the unit onto its top and using the pocket holes as guides, secure the Lower Shelf
Assembly (C) and the Upper Shelf Assembly (D) to the Legs (B) with eight #8 x 1-1/4" Pan Head
Screws (M). See Figures 6 and 6a.
Fig. 6
M
x 8
Fig. 6a
M
Fig. 5
Fig. 5a
P
R
x 2
x 2
P
R

3460AUF Stayton Media Console;
3462AUF Stayton Media Center
Assembly Instructions
3460AUF_3462AUF —Page 6 —04/13
7. Lay the unit with the drawer opening face down. The back apron of the Top Assembly has pre-
punched location holes. Place the Back Assembly (E) with the horizontal cleat of the top edge
against the back apron of the Top Assembly. Attach by inserting three #6 x 5/8” Philtruss
Screws (K) through the pre-punched location holes in the Back Apron. Insert three additional #6
x 5/8” Philtruss Screws through the holes in the bottom edge of the Back Assembly into the
Lower Shelf Assembly.
8. Turn the table upright and insert the Drawer. See Figure 8.
9. Place the unit at its final destination. To level the table, rotate the Adjustable Glides (V) found on
the bottoms of the legs. See Figure 8.
Fig. 8
V
V
Fig. 7
K
x 6
E
K
(Front View of
Back Assembly)
Fig. 7a
E
TOP

3460AUF Stayton Media Console;
3462AUF Stayton Media Center
Assembly Instructions
3460AUF_3462AUF —Page 7 —04/13
10. Tipping restraint: Locate two studs in the wall behind the unit. Attach a Clip (T1) to one wall
stud with two #8 x 2" Black Screws (T3). See Figure 10a. Attach a second clip to the unit with
two #6x5/8" Philtruss Screws (T5). See Figure 10b. Connect the two clips with the Nylon
Restraint Strap (T2). Pull the Nylon Restraint Strap (T2) tight so there is no slack. See Figures
10c and 10d. Repeat this procedure to attach the second tipping restraint. If you cannot locate
two studs, purchase the proper wall attachment hardware for your type of wall and secure the
unit.
Fig. 10a
T1
T3
Pull tight
Fig. 10d
T5
Fig. 10b
T1
B
T1
T2
T5
Fig. 10c
Pull the Nylon Restraint
Strap (T2) tight
so there is no slack.
T3

Whittier Finishing Hints
P.O. Box 2827
Eugene, OR 97402 USA
Toll Free: 800-653-3336
Ph: 541-687-0213
Fax: [phone]
www.whittierwood.com
Page 1 of 2
Rev. 04/11
Checklist of materials
□Rubber gloves
□Lint-free rags
□Paper towels
□Cotton swabs
□Tack cloth
□Drop cloth
□Stain brushes
(poly bristle
and foam)
□#220 & #320
sandpaper
□Painter’s tape
□Wood glue
Getting started
Assembly Instructions may contain special finishing
information or gluing requirements for that item.
Completely read both the Assembly Instructions and
these Finishing Hints before you begin your project.
Choosing the finish: Ask your retailer for advice on
how to finish bare wood. Choose a finish that meets
your expectations for the end use of the product. Will
you use it as a work surface as on a desk or kitchen
island? Are you matching a finish on existing furniture?
The answers to these questions may affect the type of
finish you choose.
Where to work: Choose an area that has good light and
is well ventilated, warm and dry. If the work area is cold
and damp, the wood finishing products may require a
longer drying time than the labels indicate. Do not work
in a dirty or dusty area –dirt and/or dust can embed in
the finish.
Gluing hints
These are general hints. Refer to the Assembly
Instructions for detailed information on how to glue your
specific product. Use wood glue such as Elmer’s Wood
Glue, Titebond Wood Glue or the equivalent. Some
instructions call for a slow drying epoxy glue. Carefully
read the label and instructions of the glue manufacturer.
Your unit may not need glue.
1. We strongly recommend that you lay out all the
parts and familiarize yourself with how they fit
together before assembling with glue. Glue will set
up quickly. You can damage parts if you try to
reposition any that have been assembled
incorrectly.
2. For glue to properly bond, it is very important to
apply the wood glue to bare wood. Protect your eyes
and blow into holes to clear excess dust. This will
help the glue to adhere to a clean surface.
3. If you plan on finishing the product before you
assemble it, place painter’s tape three-fourths of the
way up from the end of a dowel, spindle or tenon.
This protects the ends from the finishing product but
allows finish application where it will be visible.
Finishing products inhibit the bonding properties of
wood glue. Remove the tape prior to the final
assembly.
4. Avoid getting glue on surfaces to be finished. Most
stains or finishes will not penetrate where glue has
been spilled. Wet glue can be wiped off with a damp
cloth. Follow with a light sanding of the area to
ensure a proper finish.
5. It is important to apply an even coat inside holes and
slots. Use a small dowel, pencil or cotton swab to
spread glue evenly around the inside of the holes.
Do not over glue. The tight fit of the spindles or
dowels in the holes can cause glue to be pushed to
the bottom of the hole. If too much glue is used it will
fill the holes and not allow the spindle or dowel to be
fully inserted.
6. Glue usually takes several hours to cure or harden
but it will set up or grab in several seconds. Once
you begin final assembly, proceed quickly.
Finishing hints
1. Use products of the same brand to ensure
compatibility. It is not recommended to mix solvent
based and water based finishes. Always read and
follow all label directions on the can.
2. Alder is a porous hardwood and often looks best
when following the finishing instructions for
softwoods.
3. Use a wood conditioner under oil base stains.

Whittier Finishing Hints
P.O. Box 2827
Eugene, OR 97402 USA
Toll Free: 800-653-3336
Ph: 541-687-0213
Fax: [phone]
www.whittierwood.com
Page 2 of 2
Rev. 04/11
Preparing the surface
1. Sand each piece with #220 grit sandpaper. Sand
with the grain of the wood on flat surfaces and
opposite the grain on turnings. Some parts may be
plywood. Be careful not to sand through the veneer.
End grain such as table top ends, seat edges and
grooves on turnings accept more stain. Extra
sanding in these areas with #320 grit sandpaper
reduces stain absorption and creates a more evenly
stained piece.
2. When sanding is completed, wipe the surface of
your furniture with a lint-free rag or tack cloth. Make
sure the item is free of dust before you proceed.
Staining
1. Read and follow label directions. Stir the stain well
before you start. Stir periodically throughout the
duration of the project to maintain uniform color
consistency.
2. Test stain on an inconspicuous spot on your project.
Put at least one coat of your top coat over the test
area as it also affects the look of the stain. Test
every type of wood that is in your kit. These are
identified in the Assembly Instructions. Different
types of wood may react differently to the stain
color. You might need to add a second coat of stain
to lighter woods to match the darker woods in your
kit.
3. Apply stain with a poly brush or lint-free cloth. Apply
stain over a small area and wipe off excess.
Working in small areas will make the color easier to
control.
4. Cotton swabs are ideal for hard to reach areas.
5. Allow the stain to dry thoroughly before you
proceed.
Applying the top coat
1. Always read and follow all label directions. Stir your
top coat gently; do not shake. Shaking the can
creates bubbles that are hard to remove.
2. All surfaces including the underside of table tops
and inside drawers must be sealed with at least one
layer of a top coat. This will help minimize wood
swelling, shrinkage, warping and cupping due to
changes in moisture content or temperature.
3. Apply a minimum of two coats when you use
polyurethane or varnish (especially on all table top
and work surfaces). After allowing the first coat to
dry, sand lightly with #320 grit sandpaper. Remove
dust with a lint-free rag or tack cloth. For added
protection, apply additional coats. Lightly sand and
wipe surface with a lint-free rag or tack cloth
between coats.
4. Some finishes tend to slightly raise the grain. This
can be easily controlled with a light sanding between
coats. Do not use steel wool when you use water-
based finishes. Strands of steel fiber caught in the
wood can cause rust spots when coated with any
water-based product.
Painting
1. Since there is a large variation between paint
manufacturers and products, ask your paint supplier
for specific advice on how to best use the paint you
purchase. Ask them specifically for advice on
finishing bare wood.
2. First coat the wood with a primer. An oil based
primer works best for a smooth finish. If you do not
wish to use a solvent based primer, water based
primer works almost as well. However it may raise
the wood grain and require additional sanding.
3. Buy quality brand paint in a satin, semi-gloss, or
gloss sheen. Apply a second coat for a smooth
finish. Lightly sand between coats using with #320
grit sandpaper so that the second coat will bond
well. Be sure to use a tack cloth after sanding to
remove any residue. Repeat as desired.
4. No top coat is required when using paint.