Whittier Wood Furniture 1452AFGSPb User manual

P.O. Box 2827
Eugene, OR 97402 USA
Production Code:
VN 12/13
Model #
1452AFGSPb; 1452AFCAFb
Pacific King Storage Bed
AFGSP = Glazed Spice finish
AFCAF = Caffè finish
Assembly Instructions
Congratulations!
This fine piece of furniture will make a gorgeous
addition to your home. For the best results, read the
Assembly Instructions before you begin your project.
IMPORTANT NOTES:
For normal household use only. Not recommended to use this unit in a
commercial setting.
Unload items before you move this unit.
Do not overload the drawers.
Before you load or move this unit, tighten all screws and supports.
Before you begin your project, completely read the Assembly
Instructions.
Store this item: 1- in its box; 2- in a dry place; 3- in temperatures that
range from 40°F to 90°F (not on a cold and possibly damp cement
floor).
Periodically inspect your furniture for any loose glue joints, screws or
any other problem that might affect the stability of your furniture.
Tighten or repair as needed.
This assembly requires two people.
WARNING
Notice to California Customers
California Prop 65 requires consumer goods to be labeled if any one of
850+ different chemicals or substances, including wood dust, is present
even in trace amounts. Drilling, sawing, sanding or machining wood
products generates wood dust, a substance known to the State of
California to cause cancer. Warning: This product contains a chemical
or substance known to the State of California to cause cancer, birth
defects or other reproductive harm. California Health and Safety Code
Section 25249.6
DESIGN SUBJECT TO CHANGE WITHOUT NOTICE.
CALL US FIRST! Do not return this item to the store.
Service Policy: We will replace any part that is defective,
missing or damaged during assembly. For a replacement
part, contact Whittier Wood Products customer service
department by phone, fax, mail or email.
Hours: Our friendly customer service staff can be reached
Monday-Friday 7:00 a.m. to 5:00 p.m. (Pacific Time). You
may leave a message 24 hours a day, seven days a week.
To Order: Provide the finish and furniture model number
(upper portion of this page), the part letter, production
code, quantity needed, reason for replacement and your
full name, address and telephone number.
Parts ship from our Eugene, Oregon factory within one or
two business days from the time we receive your request.
Please allow five to ten business days for delivery
800-653-3336 •Outside the U.S. or Canada: 541-687-0213 • Fax: [phone]
www.whittierwood.com • P.O. Box 2827 • Eugene, Oregon 97402, U.S.A.

1452AFGSPb; 1452AFCAFb Pacific King Storage Bed
Parts List
1452AFGSPb_1452AFCAFb —Page 2 —12/13
Please identify the parts and check that quantities received match those on this list.
If you need to replace a part, refer to the following letter and part name.
1455AFGSPa; 1455AFCAFa
Headboard/Footboard Kit (x1)
Part
Description
Quantity
A
Headboard Assembly
1
B
Footboard Assembly
1
D
5/16" x 2-1/4" Hex Bolt
8
E
5/16" Flat Washer
8
F
1/4" x 80mm Hex Bolt
2
G
1/4" x 1-3/4" Hex Bolt
12
H
1/4" Flat Washer
12
I
Barrel Nut
2
J
3/8" x 1" Wood Dowel
2
K
Angle Bracket (attached)
2
L
#6 x 3/4" Flat Head Screw
12
(6 inserted)
S
Hex Wrench
1
U
Hanger Bolt (attached)
6
V
5/16" x 3/4" Insert Nut (inserted)
14
ZA
#6 x 1-1/4" Black Pan Head Screw (inserted)
92
ZF
Adjustable Glide with Hex Nut (installed)
6
ZG
Assembled Foot
6

1452AFGSPb; 1452AFCAFb Pacific King Storage Bed
Parts List
1452AFGSPb_1452AFCAFb —Page 3 —12/13
1453AFGSPb; 1453AFCAFb Pedestal Kit (x2)
Part
Description
Quantity
N
Pedestal Kit
1
O
Drawer Box (inserted)
3
P
Drawer Face (attached)
3
R
Drawer Slides (pre-installed sets)
3
T
T-Nut (inserted)
9
X
#7 x 1-1/2" Black Pan Head Screw (inserted)
79
ZA
#6 x 1-1/4" Black Pan Head Screw (inserted)
12
ZB
#8 x 20mm Pan Head Screw (inserted)
12
ZC
Small Angle Bracket (attached)
4
ZD
#6 x 1/2" Philtruss Screw (inserted)
42
ZE
#6 x 3/4" Philtruss Screw (inserted)
18
ZI
#8 x 7/8" Black Lo-Profile Screw (inserted)
18

1452AFGSPb; 1452AFCAFb Pacific King Storage Bed
Assembly Instructions
This assembly requires two people.
1452AFGSPb_1452AFCAFb —Page 4 —12/13
Tools Required: Hex Wrench (provided), Phillips Screwdriver, Slotted Screwdriver,
1/2" Wrench, 7/16" Wrench, Tape Measure, Rubber Mallet or Padded Hammer, Wood Glue
1. Remove the Drawers (O) from the Pedestal Kits (N). To remove the drawers, pull up on the left
Drawer Release Lever while pushing down on the right Drawer Release Lever. See Figures 1
and 1a. Note where each drawer came from to ensure correct re-installation. Positions are
marked on the drawer bottoms.
2. To protect your flooring and the surface of the unit, place the Pedestal Kits (N) face-down on top
of opened and unfolded 1453 cartons as shown in Figure 2. (When you join the pedestals,
carpet fibers can get caught in between the middle supports.) Place twelve 1/4" Washers (H)
over twelve 1/4" x 1-1/4" Hex Bolts (G) and thread each through a pre-drilled hole and into a
T-Nut in the middle support found on each pedestal. Finger tighten each bolt, making sure the
pedestals line up with each other. Afterwards, use a 7/16" wrench to securely tighten each bolt.
See Figure 2.
Fig. 1
Drawer Release Lever
Fig. 1a
O
Fig. 2
N
G
Unfolded
1453 cartons
G
H
x 12
x 12
H
T
T
T
T
T

1452AFGSPb; 1452AFCAFb Pacific King Storage Bed
Assembly Instructions
This assembly requires two people.
1452AFGSPb_1452AFCAFb —Page 5 —12/13
3. Rotate the Adjustable Glides with Hex Nut (ZF) so that the Assembled Feet (ZG) are 4-1/2" tall
as shown in Figure 3a. Attach the six Assembled Feet (ZG) as shown in Figure 3.
4. This step requires two people to move the bed to its upright horizontal position.
Rotate the bed so the deck boards face up. DO NOT PLACE UNDUE PRESSURE ON THE
ASSEMBLED FEET. See Figure 4.
Fig. 4
Fig. 3
ZG
Fig. 3a
ZG
x 6
4-1/2"
ZF

1452AFGSPb; 1452AFCAFb Pacific King Storage Bed
Assembly Instructions
This assembly requires two people.
1452AFGSPb_1452AFCAFb —Page 6 —12/13
5. Spread a thin film of glue in the dowel holes at one end of the top cap of the bed. Insert two
dowels (J) and gently tap with a rubber mallet. Quickly wipe away any excess glue. See Figures
5 and 5a.
6. Position the Footboard (B) against the end of the pedestal assembly and insert the dowels (J)
into the oval holes in the top cap of the footboard. Place four 5/16" Washers (E) over four
5/16" x 2-1/4" Hex Bolts (D) and thread the washer/bolts through the predrilled holes in the
Pedestal Assembly and into the Footboard. Tighten the bolts with a 1/2" wrench.
See Figures 6, 6a and 6b.
Fig. 5
J
J
x 2
J
Fig. 5a
Top Cap
J
Fig. 6
Top Cap
J
D
E
x 4
x 4
J
Fig. 6a
D
E
B
Fig. 6a
D
E
J

1452AFGSPb; 1452AFCAFb Pacific King Storage Bed
Assembly Instructions
This assembly requires two people.
1452AFGSPb_1452AFCAFb —Page 7 —12/13
7. Position the Headboard (A) against the end of the pedestal assembly. Place four 5/16" Washers
(E) over four 5/16" x 2-1/4" Hex Bolts (D) and thread the washer/bolts through the predrilled
holes in the Pedestal Assembly and into the Headboard. Tighten the bolts with a 1/2" wrench.
See Figure 7.
8. Secure the pre-attached Angle Brackets (K) on the Headboard to the Pedestal Assembly with
six #6 x 3/4" Flat Head Screws (L). See Figures 8 and 8a. Insert one Barrel Nut (I) into the pre-
drilled holes on the bottom of the left pedestal rail. Using a slotted screwdriver, line up the hole
in the Barrel Nut to the hole in the Headboard. Insert one 1/4" x 80mm Hex Bolt (F) into the pre-
drilled hole in the Headboard and tighten with the provided Hex Wrench (S). Repeat for the right
side. See Figures 8 and 8b.
Fig. 8
F
I
x 2
x 2
L
x 6
L
F
K
I
F
Fig. 8b
Fig. 7
E
D
E
x 4
x 4
D

1452AFGSPb; 1452AFCAFb Pacific King Storage Bed
Assembly Instructions
This assembly requires two people.
1452AFGSPb_1452AFCAFb —Page 8 —12/13
9. Place your bed into its final position; verify that all 6 Assembled Feet (ZG) are touching the floor
and carrying weight, if needed, use a 1/2" wrench to adjust the Adjustable Glides (ZF) on the
bottoms of the Assembled Feet (ZG). See Figure 9.
Carefully align the drawer slides and gently insert the six drawers into their correct positions.
Sleep well and enjoy!
Fig. 9
ZG
ZF