Whittier Wood Furniture Bryce 1104RLN User manual

P.O. Box
2827
Eugene, OR 97402 USA
Production Code:
VN 10/19
Bryce Nightstands
RLN = Ridgeline finish
Assembly Instructions
Model #
IMPORTANT NOTES:
•Wood can be susceptible to changing color over time when exposed to
strong sunlight. Use window shades, drapes or blinds to protect your
furniture. To help the surface age evenly and avoid dark and light
spots, periodically move items to expose the entire surface to an even
amount of light so it may develop a uniform patina.
•For normal household use only. Not recommended for commercial use.
•Do not climb, sit or stand on this piece of furniture.
•Do not overload the drawers.
•Unload items before you move this unit.
WARNING
Drilling, sawing, sanding or machining wood products can expose you to
wood dust, a substance known to the state of California to cause cancer.
Avoid inhaling wood dust or use a d
ust mask or other safeguards for
personal protection.
For more information go to: www.p65warnings.ca.gov/wood
This product can expose you to chemicals, including formaldehyde,
which are known to the State of California to cause cancer.
For more information go to: www.p65warnings.ca.gov/furniture
DUAL PORT USB WALL CHARGER: CAUTION: Changes or modifications not
approved by the party responsible for compliance could void user’s authority to
operate the equipment .
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the use is encouraged to
try to correct the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver
•Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
DESIGN SUBJECT TO CHANGE WITHOUT NOTICE.
CUSTOMER SERVICE
If you ever have questions about your furniture, please do not hesitate to contact us. In the unlikely event you need a
replacement part; we can make those parts available through an authorized Whittier Wood Furniture dealer. If you
cannot order replacement parts through your dealer, please contact our customer service department.
Hours: Our friendly customer service staff can be reached:
Monday-Friday 8:00 a.m. to 5:00 p.m. (Pacific Time).
You may leave a message 24 hours a day, seven days a week.
Customer Service: 800-653-3336 • Outside the U.S.: 541-687-0213
Fax: [phone]• Email: [email protected]
Thank you for allowing us to help you furnish your
home. We are certain you will be delighted with
your new furniture for many years to come.
1104RLN
Bryce 2 Drawer
Nightstand
1105RLN
Bryce 3 Drawer
Nightstand

1104RLN & 1105RLN Bryce Nightstands
Parts List
1104RLN_1105RLN — Page 2 — 09/19
Please identify the parts and check that quantities received match those on this list.
If you need to replace a part, refer to the following letter and part name.
Part
Description
Quantity
1104RLN
1105RLN
A
Case
1
1
B
Small Drawer Box (inserted)
2
2
C
Large Drawer Box (inserted)
0
1
D
Upper Drawer Face (installed)
1
1
E
Center Drawer Face (installed)
0
1
F
Lower Drawer Face (installed)
1
1
G
Base (attached)
1
1
H
14" Drawer Slides (pre-installed sets)
2
3
I
#6 x 3/4" Philtruss Screw (inserted)
12
18
K
#6 x 1/2" Philtruss Screw (inserted)
12
18
L
#8 x 1-3/8" Lo-Profile Screw (inserted)
4
4
M
#8 x 1-1/4" Pan Head Screw (inserted)
22
26
N
#8 x 7/8" Black Lo-Profile Screw (inserted)
8
12
O
#8 x 1-3/4" Pan Head Screw (inserted)
14
14
P
#7 x 1-1/2" Black Pan Head Screw
8
8
Q
#8 x 1-1/2" Machine Screw Tuscan (installed)
4
6
R
1/4" x 20mm Insert Nut (inserted)
4
4
S
5/32" x 10mm Insert Nut (inserted)
4
6
T
USB Power Supply (attached)
1
1
U
Dual Port USB (attached)
1
1
V
Pull (attached)
2
3
W
Brass Plate (attached)
2
3
X
Small Adjustable Glide (installed)
4
4
Y
#8 x 1" Black Screw (inserted)
2
2
1105 shown in the illustrations.
Assembly Instructions
1. Place the unit at its final destination. Rotate the Small Adjustable Glides (X) on the bottoms of
the legs until the unit is level. See Figure 1.
Fig. 1
X
X