Whittier Wood 3456AFCAF User manual

P.O. Box 2827
Eugene, OR 97402 USA
Production Code:
VN 04/13
Model #
3456AFCAF
Stayton Cocktail Table
AFCAF = Caffè finish
Assembly Instructions
Congratulations!
This fine piece of furniture will make a gorgeous addition to
your home. For the best results, read the Assembly
Instructions before you begin your project.
IMPORTANT NOTES:
For normal household use only. Not recommended for
commercial use.
Do not climb, sit or stand on this piece of furniture.
Unload items before you move this unit.
Do not overload the drawer or shelf.
Before you load or move this unit, tighten all screws and
supports.
Before you begin your project, completely read the
Assembly Instructions.
Store this item: 1- in its box; 2- in a dry place; 3- in
temperatures that range from 40°F to 90°F (not on a cold
and possibly damp cement floor).
Periodically inspect your furniture for any loose glue
joints, screws or any other problem that might affect the
stability of your furniture. Tighten or repair as needed.
DESIGN SUBJECT TO CHANGE WITHOUT NOTICE.
CALL US FIRST! Do not return this item to the store
Service Policy: We will replace any part that is defective,
missing or damaged during assembly. For a replacement
part, directly contact Whittier Wood Products customer
service department by phone, fax, mail or email.
Hours: Our friendly customer service staff can be reached
Monday-Friday 7:00 a.m. to 5:00 p.m. (Pacific Time). You
may leave a message 24 hours a day, seven days a week.
To Order: Provide the finish and furniture model number
(upper portion of this page), the part letter, production
code, quantity needed, reason for replacement and your
full name, address and telephone number.
Parts ship from our Eugene, Oregon factory within one or
two business days from the time we receive your request.
Please allow five to ten business days for delivery.
800-653-3336 •Outside the U.S. or Canada: 541-687-0213 • Fax: [phone]
www.whittierwood.com • P.O. Box 2827 • Eugene, Oregon 97402, U.S.A.

3456AFCAF Stayton Cocktail Table
Parts List
3456AFCAF —Page 2 —04/13
Please identify the parts and check that quantities received match those on this list.
If you need to replace a part, refer to the following letter and part name.
Part
Description
Quantity
A
Top Assembly (attached)
1
B
Left Front/Right Back Leg
2
C
Right Front/Left Back Leg
2
D
Shelf Assembly
1
E
Drawer Box (inserted)
1
F
Drawer Face (installed)
1
G
PVC Wheel (installed)
4
H
Drawer Slides (pre-installed sets)
1
I
Axle Pin (inserted)
4
J
#6 x 3/4" Philtruss Screw (inserted)
6
K
#6 x 1/2" Philtruss Screw (inserted)
6
L
#8 x 1" Lo-Profile Screw (inserted)
6
M
#8 x 1-1/4" Pan Head Screw
34
(30 inserted)
N
#8 x 1-1/2" Machine Screw (installed)
4
O
#8 Washer (inserted)
23
P
5/16" Flat Washer
4
Q
3/8" x 1" Insert Nut (inserted)
4
R
3/8" x 2-1/2" Hex Bolt
4
S
4 x 10mm Insert Nut (inserted)
4
T
Pull (installed)
2
U
Wood Dowel (inserted)
4
V
#8 x 20mm Pan Head Screw (inserted)
9
W
Adjustable Angle Bracket (attached)
3

3456AFCAF Stayton Cocktail Table
Assembly Instructions
3456AFCAF —Page 3 —04/13
Tools Required: Phillips Screwdriver, 9/16" or Adjustable Wrench, Rubber Mallet or Padded
Hammer
1. Remove the Drawer (E) from the Top Assembly (A). To remove the drawer, pull up on the left
side of the Drawer Release Lever while pushing down on the right Drawer Release Lever. See
Figure 1a.
2. Turn the Top Assembly (A) upside-down on a clean, protected surface. Place a Left Front/Right
Back Leg (B) and a Right Front/Left Back Leg (C) at the back of the Top Assembly (A), making
sure the drilled corners of the legs face toward the Corner Blocks. It is important the sides of the
legs exposing the wheel face the drawer opening of the unit. Attach with 5/16" Flat Washers (P)
and 3/8" x 2-1/2" Hex Bolts (R). See Figures 2 and 2a.
Fig. 1
Drawer Release Lever
Fig. 1a
Fig. 2
C
B
Fig. 2a
A
P
R
x 2
x 2
R
P

3456AFCAF Stayton Cocktail Table
Assembly Instructions
3456AFCAF —Page 4 —04/13
3. Rotate the Top and Leg assembly so that is sets on the back legs. Turn the Shelf Assembly (D)
bottom-side-down and place the dowels into the dowel holes in the Legs. See Figure 3.
4. Using the dowels as guides, place the remaining Left Front/Right Back Leg (B) and Right
Front/Left Back Leg (C) in the remaining two corners making sure the drilled corners of the Legs
face toward the Corner Blocks. It is important the side of the leg exposing the wheel face toward
the back of the unit. See Figure 4.
Fig. 4
Fig. 4a
B
C
Fig. 3
D

3456AFCAF Stayton Cocktail Table
Assembly Instructions
3456AFCAF —Page 5 —04/13
5. Attach the legs to the Top Assembly with 5/16" Flat Washers (P) and 3/8" x 2-1/2" Hex Bolts (R)
See Figures 5 and 5a.
6. Turn the unit onto its top and using the pocket holes as guides, secure the Shelf Assembly (D)
to the Legs (B and C) with four #8 x 1-1/4" Pan Head Screws (M). See Figures 6 and 6a.
Fig. 6
M
x 4
Fig. 6a
M
Fig. 5
Fig. 5a
P
R
x 2
x 2
P
R

3456AFCAF Stayton Cocktail Table
Assembly Instructions
3456AFCAF —Page 6 —04/13
7. Turn the table upright and insert the Drawer. See Figure 7.
8. The wheels allow the table to easily move away from or toward your seating.
Fig. 7
Fig. 8a
Fig. 8