Whittier Wood 1123GACf User manual

P.O. Box 2827
Eugene, OR 97402 USA
Production Code:
VN 12/16
Model #
1123GACf;
1123CAFf
McKenzie Office Chest
GAC = Glazed Antique Cherry finish
CAF = Caffè finish
Assembly Instructions
IMPORTANT NOTES:
•For normal household use only. Not recommended for commercial use.
•Do not climb, sit or stand on this piece of furniture.
•Do not overload the drawers.
•Unload items before you move this unit.
•This assembly requires two people.
WARNING
Serious or fatal crushing injuries can occur from furniture tip-over. Use of
tip-over restraints may only reduce but not eliminate the risk of tip-over.
To help prevent tip-over:
•Place heaviest items in the bottom drawers.
•Unless specifically designed to accommodate, do not set TVs or other
heavy objects on top of this product.
•Never allow children to climb or hang on drawers, doors or shelves.
•Never open more than one drawer at a time.
•Do not defeat or remove the drawer interlock system.
Warning: At least one tipping restraint kit was included with your piece of
Whittier Wood Furniture. When you receive your furniture, be sure to find
and properly install the tipping restraint(s). If you cannot locate the
restraint(s), please contact us immediately for replacement.
Drilling, sawing, sanding or machining wood products can expose you to
wood dust, a substance known to the state of California to cause cancer.
Avoid inhaling wood dust or use a dust mask or other
safeguards for
personal protection.
For more information go to: www.p65warnings.ca.gov/wood
This product can expose you to chemicals, including formaldehyde,
which are known to the State of California to cause cancer.
For more information go to: www.p65warnings.ca.gov/furniture
DESIGN SUBJECT TO CHANGE WITHOUT NOTICE.
CUSTOMER SERVICE
If you ever have questions about your furniture, please do not hesitate to contact us. In the unlikely event you need a
replacement part; we can make those parts available through an authorized Whittier Wood Furniture dealer. If you
cannot order replacement parts through your dealer, please contact our customer service department.
Hours: Our friendly customer service staff can be reached:
Monday-Friday 8:00 a.m. to 5:00 p.m. (Pacific Time).
You may leave a message 24 hours a day, seven days a week.
Customer Service: 800-653-3336 • Outside the U.S.: 541-687-0213
Fax: [phone]• Email: [email protected]
Thank you for allowing us to help you furnish your
home. We are certain you will be delighted with
your new furniture for many years to come.

1123GACf; 1123CAFf McKenzie Office Chest
Parts List
1123GACf_1123CAFf — Page 2 — 12/16
Please identify the parts and check that quantities received match those on this list.
If you need to replace a part, refer to the following letter and part name.
Part
Description
Quantity
Af
Top Assembly
1
Bf
Case
1
C
Hutch Drawer (inserted)
2
D
Small Drawer Box (inserted)
1
E
Large Drawer Box (inserted)
1
F
Small Drawer Face (installed)
1
G
Large Drawer Face (installed)
1
H
Adjustable Shelf (attached)
1
I
Door (attached)
1
J
Insert Nut (inserted)
4
K
Small Adjustable Glide (installed)
4
L
Large Knob (attached)
4
Md
#8 x 1-1/2" Machine Screw Tuscan (installed)
4
N
Small Knob (attached)
3
O
4x32mm Machine Screw (installed)
1
Pf
14" Drawer Slides (pre-installed sets)
2
Q
#6 x 1/2" Philtruss Screw (inserted)
18
R
#6 x 3/4" Philtruss Screw (inserted)
15
S
Hinge (attached)
2
V
#6 x 5/8" Philtruss Screw (inserted)
6
W
#6 x 5/8" Undercut Screw ZN (inserted)
0 (GAC)
12 (CAF)
Y
Shelf Bracket (attached)
4

1123GACf; 1123CAFf McKenzie Office Chest
Parts List
1123GACf_1123CAFf — Page 3 — 12/16
Part
Description
Quantity
ZA
#6 x 1/2" Undercut Screw (inserted)
4
ZC
#8 x 1-1/4" Pan Head Screw (inserted)
14
ZD
#8 x 20mm Pan Head Screw (inserted)
4
ZH
#8 x 1-3/8" Lo-Profile Screw (inserted)
8
ZI
Tuscan Magnetic Lock & Plate (pre-installed sets)
2
ZJ
#6 x 5/8" Undercut Screw AB (inserted)
16 (GAC)
4 (CAF)
ZK
Lid Support (attached)
2
ZL
#5 x 5/8" Flat Head Screw (inserted)
4
ZM
#8 Washer (inserted)
2
ZN
#8 x 7/8" Black Lo-Profile Screw (inserted)
12
ZO
4x35mm Machine Screw (installed)
2
ZP
Anti-Tip Snapper (attached)
1
ZQ
Drawer Clip (attached)
2
ZR
#8 x 1-1/4" Black Screw (inserted)
12
TS
Furniture Tipping Restraint (attached)
1 set

1123GACf; 1123CAFf McKenzie Office Chest
Assembly Instructions
1123GACf_1123CAFf — Page 4 — 12/16
Tools Required: Phillips Screwdriver, Pencil.
1. This piece of furniture includes a drawer interlock system allowing only one lower drawer to be
open at a time. This is a safety feature to reduce the risk of tip over. Do not defeat or remove the
drawer interlock system.
2. Place the chest at its final destination. Rotate the Small Adjustable Glides (K) on the bottoms of
the legs until the unit is level. See Figure 2.
3. To move the Adjustable Shelf (H), remove the #6 x 1/2" Undercut Screws (ZA) and the Shelf
(H). Reposition the Shelf Brackets (Y) to the desired positions, replace the shelf and insert the
screws. See Figures 3 and 3a.
Fig. 3
H
ZA
Y
Fig. 3a
K
K
Fig. 2

1123GACf; 1123CAFf McKenzie Office Chest
Assembly Instructions
1123GACf_1123CAFf — Page 5 — 12/16
4. If you need to remove your drawers, pull up on the left Drawer Release Lever while pushing
down on the right Drawer Release Lever and pull out the drawer. See Figures 4 and 4a. Note
where each drawer came from to make sure you place them back into their correct positions.
5. When removing drawers from furniture featuring the Anti-Tip Drawer Interlock System it is
important that the drawer be installed back in its original location. Numbers and letters are
stamped on the back of the drawers. Stamping sequence starts at the bottom, moves to the top
and designated left or right.
Drawer back stamping example:
1
Fig. 5
2
Fig. 4
Drawer Release Lever
Fig. 4a