Wi-Tek WI-CPE211 User manual

Installation Guide
Long-Range Wireless Transmit CPE
2.4G and 5.8G Wireless CPE

※ If you find any items are missing or damage, please feel free to contact your supplier.
Itme Unit
1
2
3
1
1
2
Strapping tape
wireless bridge
This guide applies to:
WI-CPE211,WI-CPE513,WI-CPE515,WI-CPE516,WI-CPE517,WI-CPE518
,WI-CPE214SMA,WI-CPE514SMA WI-CPE515-KIT,WI-CPE518-KIT,
WI-CPE213-KIT.This guide introduces how to build a wireless network
using the CPE products:
1. Check the System Requirements
2. Log In to the Device
3. Set Up the Wireless Network
4. WI-CPE515-KIT,WI-CPE518-KIT,WI-CPE213-KIT is pre-configuration
software, so can do Point to Point by auto-connect
The following parts detailedly introduces these steps.
,
Product Profile
1
POE adapter

2
Product exterior and Guiding lights
Guiding lights
Reset
Port of Ethernet
Sigal lights
Power
Ethernet
以太网 口
SYS
3
Specification
27dBm
-95dBm@6Mbps
11n:300Mbps (40M Channel width)
144Mbps (20M Channel width)
-40ºC~+70ºC
263×102×106mm
Hardware specification
Item
Standard
Wireless Setting
Dimensions
Wireless mode
Wireless setting
Maximum
transmission speed

Installation
Outdoor installation manual
While outdoor wireless long distance transmitting encounter obstacle such as
top buildings or trees, the signal will be weak ; This is a directional bridge, the
best signal will be obtained once it forwards to radiation range, so the alignment
of antenna is important .
First of all, confirm the installation position:
3

4
Connection and Installation
Upward push the Rear cover
plate after connection
According to the network
topology, connect the POE
with PC, Router or Switch.
Adjust the CPE toward the
direction you choose.
复位键
NVR
GPS-5 -65W Gi gabit Po E Swit ch
5-Port Gigabit Ethernet Switch With 4-Port PoE
PoE-Ports
1 2 3 4 5
LAN 100Mbps 1000Mbps
UP/Link
LAN
LAN
3 5
2 4
PWR
1
PoE
PoE
100m

Device Setting
Step 1:Click on the icon at the lower right of computer to open'Open Network and
Sharing Center'.
5

Step5: Open the browser of computer and input 192.168.1.88, you will see the
following page layout, the user name and password both are: admin.
6

Point to point connection
For point to point connection, please setting one device from two as 'AP mode' ,
another one as 'Client mode', the SSID, the way of encryption and password of
these two devices are both the same, then they will connect and work with each
other automatically.
Switch
Camera
7
Switch
Power Main Secondary
GPS-5-65W Gigabit PoE Switch
5-Port Gigabit Ethernet Switch With 4-Port PoE
PoE-Ports
1 2 3 4 5
100Mbps 1000Mbps
3 5
2 4
1
PoE
PoE
GPS-5-65W Gigabit PoE Switch
5-Port Gigabit Ethernet Switch With 4-Port PoE
PoE-Ports
1 2 3 4 5
100Mbps 1000Mbps
3 5
2 4
1
PoE
PoE

8

9

10

11

12

Point to Multipoint Connection
The AP and Client mode setting of Point to Multipoint connection are the same
as point to point configuration.
60°
Switch
Camera
GPS-5-65W Gigabit PoE Switch
5-Port Gigabit Ethernet Switch With 4-Port PoE
PoE-Ports
1 2 3 4 5
100Mbps 1000Mbps
3 5
2 4
1
PoE
PoE
Power Main Secondary
WIRELESS-TEK TECHNOLOGY LIMITED
www.wireless-tek.com
Email:[e-mail]
Technical Support:[e-mail]