Wide M series User manual

- 1 -
World Innovative Display Engineering
806-3, Yangcheng-ri, Ochang-myun,
Cheongwon-gun, Chungbuk, Korea
Tel : [phone], Fax: [phone]
V05-O-24
Quick Installation Guide

- 4 -
World Innovative Display Engineering
806-3, Yangcheng-ri, Ochang-myun,
Cheongwon-gun, Chungbuk, Korea
Tel : [phone], Fax: [phone]
V05-O-24
M-Series with Matrox/Other Graphics Adaptor
VideoAdaptor - Please install video adaptor and its drivers.
- For the installation details, please refer to the installation guide
provided by the hardware manufacturers.
Connecting Cables - Please make all cable connections in Landscape mode. Connectors
are located on the side of the monitor. Please refer to the figure
above.
- Please connect power cable to the power adaptor connector.
- Please connect video cables to DVI-1 for Display 1 and DVI-2 for
Display 2.
※ For a single Display configuration, please use DVI-1.
Power
DVI-D
USB Up
USB Down
Display 1
Display 2
DVI-D 1
DVI-D 2
USB

- 5 -
World Innovative Display Engineering
806-3, Yangcheng-ri, Ochang-myun,
Cheongwon-gun, Chungbuk, Korea
Tel : [phone], Fax: [phone]
V05-O-24
※ USB Connection
: To the Display
: To the Computer
※ When you change the orientation to Portrait, please tilt the monitor
first. Then turn it counterclockwise. If you change the monitor orientation
without tilting it first, you might damage the monitor head and monitor
base.
※ When you change its orientation to Landscape again, please tilt the
monitor first, and then turn it clockwise.
Lumical™ S/W
Installation
- Insert accompanied Lumical™ Application CD into CD-Rom in your
computer and run “lumicalinstall.exe”
- For a detailed installation guide, please refer to the following
section.
With Realvision Graphics Adaptor
ÎLumical™ S/W Installation with RealVision Graphics
Adaptor
With Matrox or other GraphicsAdaptor
ÎLumical™ S/W Installation with Matrox/Other Grpahics
Adaptor
Tilt First Turn the monitor counterclockwise

- 15 -
World Innovative Display Engineering
806-3, Yangcheng-ri, Ochang-myun,
Cheongwon-gun, Chungbuk, Korea
Tel : [phone], Fax: [phone]
V05-O-24
Installation Manual

- 18 -
World Innovative Display Engineering
806-3, Yangcheng-ri, Ochang-myun,
Cheongwon-gun, Chungbuk, Korea
Tel : [phone], Fax: [phone]
V05-O-24
Setting up Display
After installing Video Adaptor and Drivers and rebooting PC, you will see that the resolution of
the display is not correct. You can set a correct resolution by going through the following steps.
Step 1. Go to the control panel, and double click “Display” icon. Then select “Display
Properties.” Now Select “Setting” tab.
Step 2 If there is a presence of on-board video adaptor or another video adaptor in
addition to RealVision video adaptor, then you will see on additional small
monitor which is not going to be used. Select one monitor 2 and click “Extend
my Windows desktop… .”
1
2 3

- 19 -
World Innovative Display Engineering
806-3, Yangcheng-ri, Ochang-myun,
Cheongwon-gun, Chungbuk, Korea
Tel : [phone], Fax: [phone]
V05-O-24
Step 4 Click “Advanced ÆAdaptor ÆList All Modes.” And select a video mode that
you want to use.
1M 2M 3M 5M
Landscape 1280x1024 1600x1200 2048x1536 2560x2048
Portrait 1024x1280 1200x1600 1536x2048 2048x2560
* If you are using a dual monitor configuration, please repeat from Step 1 to
Step 4 for the second display.

- 27 -
World Innovative Display Engineering
806-3, Yangcheng-ri, Ochang-myun,
Cheongwon-gun, Chungbuk, Korea
Tel : [phone], Fax: [phone]
V05-O-24
Lumical™ S/W Installation
With Matrox/Other Graphics Adaptor
Preparation ※Please connect supplied USB cables to connect WIDE display to
computer you are using.
Computer (Square Head) ÅÆ (Flat Head) Monitor
Monitor Driver Installation
- Make sure that monitor is turned on before connecting USB cable to a
host computer
- Please do not use “Automatic Driver Installation.” When Windows
asks you for “Automatic Driver Installation,” please select “No.” Then
install the monitor driver manually. Monitor driver is located in
“Program Files/RealVision/Lumical/” directory.
S/W
Installation &
Configuration
Step 1. Run “LumicalInstall.exe”
You will see the following pop-up window.
Uncheck “This display is not controlled,” check box as it is shown above. And
select “It does not divide” in “Type of Division” menu.
Step 2. Please select “Yes” to for the following pop-up window.

- 28 -
World Innovative Display Engineering
806-3, Yangcheng-ri, Ochang-myun,
Cheongwon-gun, Chungbuk, Korea
Tel : [phone], Fax: [phone]
V05-O-24
Step 3. Please select “Yes” to for the following pop-up window.
Step 4. Please select “No” to for the following pop-up window.
Step 5. Please select “Yes” to confirm the configuration.
※ This procedure will be automatically started when you install Lumical™
S/W for the first time. When it does not start automatically, please run
LumicalClient by double clicking on either “LumicalClient” or
“Configuration Dialog.”
After Lumical™ Installation you will find the following icons on the background
of Windows. Double click “Configuration Dialog” or “LumicalClient.”
A pop up window appears. Please select “WideUSBIF.dll.”

- 29 -
World Innovative Display Engineering
806-3, Yangcheng-ri, Ochang-myun,
Cheongwon-gun, Chungbuk, Korea
Tel : [phone], Fax: [phone]
V05-O-24
Optional Number 1
This is used as a unique identifier for a display. For display 1, please use “20.”
For display 2, please use “30.”
Note. You can use any arbitrary numbers. Just make sure that you are
designating two different numbers to each monitor. Again, these numbers
are used as unique identifiers.
Optional Number 2
This is a nubmer reserved for a service purpose. Leave it as it is.
Optional String
Please find a serial number from the lable on the back and enter the serial
number of each display.
Now the dipslay set up is completed. You will find a quick start button on the
Windows menu bar. Right click on the icon and select “Execution Dialog.”
Note ※When you run Lumical™ Client program for the first time, you will be asked
to enter a licence key. Please enter a valid licence key that is printed on your
Limical™ application S/W CD.
※If you want to enter a licence key later, then please select “Cancel.” You

- 30 -
World Innovative Display Engineering
806-3, Yangcheng-ri, Ochang-myun,
Cheongwon-gun, Chungbuk, Korea
Tel : [phone], Fax: [phone]
V05-O-24
can use fully functional Lumical™ S/W upto 30 days after the installation. If
you do not provide a valid Licence key during this trial period, the program will
be deactivate itself.