Wide RDP2010UX(-TS) User manual

Issued Date
Revision Status
Title Page No.
1 / 39
V2.8 2008-07-31
RDP2010UX
(AL20SUX)
USER’S MANUAL
RDP2010UX(-TS)
RDP2010TS
1600 x 1200(20.1") TFT LCD MONITOR
Proprietary Data Notice:
This document as well as all reports, drawings, data, information, or other material, whether accompanying it are the property of
WIDE Corporation, are disclosed by WIDE only in confidence, and, except as WIDE may otherwise permit in writing, are to be
used, disclosed, or copied only to the extent necessary for the evaluation thereof by recipient, or higher-tier contractor or
subcontractor.
Information in this document is subject to change without prior notice.

Issued Date
Revision Status
Title Page No.
2 / 39
V2.8 2008-07-31
RDP2010UX
(AL20SUX)
Table of Contents
SAFETY INSTRUCTIONS .................................................................................................................3
BRIEF DESCRIPTION.......................................................................................................................5
GENERAL..........................................................................................................................................5
1. TECHNICAL SPECIFICATIONS ...............................................................................................7
1.1 ELECTRO-OPTICAL SPECIFICATIONS............................................................................7
1.1.1 Screen Specifications .................................................................................................7
1.1.2 Optical Characteristics ...............................................................................................7
1.1.3 Input Signal Specifications.........................................................................................8
1.1.4 Controls of the Display ...............................................................................................8
1.1.5 LED Indicator ...............................................................................................................9
1.1.6 Power Supply Specification .......................................................................................9
1.1.7 Connectors...................................................................................................................9
1.1.8 Connection & PIN Assignment.................................................................................10
1.2 MECHANICAL SPECIFICATIONS....................................................................................12
1.2.1 Dimension and Weight (Rack Mount ).....................................................................12
1.2.2 Mounting.....................................................................................................................13
1.2.3 Finishing.....................................................................................................................14
1.2.4 Screws/Bolts ..............................................................................................................14
1.2.5 Components...............................................................................................................14
1.2.6 Cooling .......................................................................................................................14
1.3 ENVIRONMENTAL SPECIFICATIONS.............................................................................14
1.3.1 Temperature, Vibration, Shock, Humidity(Except touch screen model)..............14
1.3.2 EMC(Except touch screen model) ...........................................................................14
1.3.3 Drip-proof...................................................................................................................14
1.4 OHTER SPECIFICATIONS................................................................................................15
1.4.1 Maintainability............................................................................................................15
1.4.2 Use of toxic materials ...............................................................................................15
1.4.3 Packing.......................................................................................................................15
2 User Controls .........................................................................................................................16
2.1 Operation ..........................................................................................................................16
2.2 USER Control Access......................................................................................................17
2.3 OSD(ON SCREEN DISPLAY) Navigation........................................................................17
2.3.1 Adjustment.................................................................................................................18
2.3.2 COLOR ADJ................................................................................................................21
2.3.3 PIP MENU ( CVBS Model Only ) ...............................................................................24
2.3.4 SETUP MENU.............................................................................................................26
Appendix A: Touch screen driver installation(only for RDP2010TS)........................................33

Issued Date
Revision Status
Title Page No.
3 / 39
V2.8 2008-07-31
RDP2010UX
(AL20SUX)
SAFETY INSTRUCTIONS
Precautions
ON SAFETY
1. Before connecting the AC power cord to monitor, make sure the voltage designation of the monitor
corresponds to the local electrical supply..
2. Never insert anything metallic into the cabinet openings of the monitor; doing so may create the
danger of electric shock..
3. To avoid electric shock, never touch the inside of the monitor. Only a qualified technician should open
the case of the monitor.
4. Never use your monitor if the power cord has been damaged. Do not allow anything to rest on the
power cord, and keep the cord away from areas where people can trip over it.
5. Be sure to hold the plug, not the cord, when disconnecting the monitor from an electric socket.
6. Unplug your monitor when it is going to be left unused for an extended period of time.
7. Unplug your monitor fromAC outlet before any service.
8. If your monitor does not operate normally - in particular, if there are any unusual sounds or smell
coming from it – unplug it immediately an authorized dealer or service center.
ON INSTALLATION
1. Openings and fans in the monitor cabinet are provided for ventilation. To prevent overheating, these
openings and fans should not be blocked or covered. Also avoid using the monitor on a bed, sofa rug,
or other soft surface, doing so may block the ventilation openings and fans in the monitor cabinet. If
you put the monitor in the enclosed space, be sure to provide adequate ventilation.
2. Put your monitor in a location with low humidity and minimum of dust.
3. Do not expose the monitor to rain or use it near water. If the monitor, accidentally, get wet, unplug it
and contact an authorized dealer immediately. You can clean the monitor with damp cloth if necessary,
but be sure to unplug the monitor first.
4. Place your monitor on a solid surface and treat it carefully.
5. Locate your monitor near an easily accessibleAC outlet.
6. High temperature can cause problems. Do not use your monitor in direct sunlight and keep it away
from heater, stoves and other sources of heat.
CAUTION: DOUBLE POLE / NEUTRAL FUSING.
DISCONNECT POWER BEFORE CHANGING FUSE.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

Issued Date
Revision Status
Title Page No.
4 / 39
V2.8 2008-07-31
RDP2010UX
(AL20SUX)
ON CLEANING
The screen is made of thin glass with a plastic surface and can be damaged if dropped, hit and scratched.
Do not clean the front panel with keton-type materials(e.g., acetone), ethyl alcohol, toluene, ethyl acid,
methyl or chloride – these may damage the panel.
ON REPACKING
Do not throw away the carton and packing materials. They make an ideal container which to transfer the
unit. If you have any questions about this unit, contact your authorized dealer.
ON DISPOSAL
This unit contains which can pollute the environment if disposed carelessly. Please contact our nearest
representative office or your local environmental office in case of disposal of this unit.
ON VESA MOUNTING
zMake sure to unplug before installing this product. Otherwise, it may cause a fire or could give
an electric shock.
zDo not install this product by yourself. Contact the qualified service technician. Otherwise, it may
cause injuries.
zDo not install this product on the place where it cannot be supported. Otherwise, it may cause
the product to fall and could cause injuries.
zContact the qualified service technician for moving or replacing this product after installing.
Installing the product needs specified technique, so it may cause safety problem to move or
install it by yourself.
zDo not hang on or impact on this product. Otherwise, it may cause the product to fall and could
cause injuries.
zDo not install this product by alone. Get some help from others. Otherwise, it may cause the
product to fall and could cause injuries.
zDo not place a heat source or a humidifier under the installed product. Otherwise, it may cause a
fire or could give an electric shock.
zDo not install this product near a high voltage electric line, any power source or the place where
impact or vibration can affect.
zDo not install this product barehanded. Otherwise, it may cause injuries.
zThe screw is not provided to user as default. Use the screw, which can stand the weight of this
product. And, we recommend the machine screw BH(+)M4 x 14mm to 18mm as type

Issued Date
Revision Status
Title Page No.
5 / 39
V2.8 2008-07-31
RDP2010UX
(AL20SUX)
BRIEF DESCRIPTION
GENERAL
This specification defines the requirements for the RDP2010UX, 20.1” COLOR DISPLAY TFT LCD
monitor with 1600 X 1200 pixels visible resolution, which is designed and tailored for use in operator
display systems such as Rugged and Industrial monitor applications.
The RDP2010UX has a 20.1” diagonal viewable display area and 1600 x 1200 pixels addressable
resolution. The (0.085 X RGB) X 0.255 mm dot pitch LCD provides the most accurate and crisp images
on the screen for mission critical applications.
The RDP2010UX provides 16.7 million true colors (8-bit) per pixel. Each pixel is divided into Red, Green
and Blue sub pixels which are arranged in vertical stripes and each sub-pixel is controlled in 256 grey
levels.
The RDP2010UX is standard rack mountable. And, touch-screen of resistive type may be provided
as option.
KEY FEATURES
zColor display 20.1” TFT LCD Monitor
zFull 1600 x 1200 resolution
zTwo Analog (BNC and D-sub) input, single DVI-D input.
zRS-422, RS-485 and RS-232 Communication
zVersatile mechanical version : Rack mount, Desktop Type(T.B.D) , VESA Mount Type(T.B.D)
zFree Voltage power : AC 100 ~ 250Vac, 50/60Hz±3
zOption: Resistive type Touch screen, Serial control(DB-9)
INPUT DIAGRAM
RDP2010UX (Touch screen option)
①Power Switch ②Power Inlet
③Serial Interface ④DVI-D Input
⑤Touch Screen Serial Control (option) ⑥D-Sub Input
⑦ BNC Input

Issued Date
Revision Status
Title Page No.
6 / 39
V2.8 2008-07-31
RDP2010UX
(AL20SUX)
RDP2010UX (CVBS option)
①Power Switch ②Power Inlet
③Serial Interface ④DVI-D Input
⑤Touch Screen Serial Control (option) ⑥D-Sub Input
⑦ Composite Video Input(BNC)
RDP2010UX (MIL MS-3100F10SL-3P option)
①Power Switch ②AC MIL power Inlet
③Serial Interface ④DVI-D Input
⑤D-Sub Input ⑥ BNC Input
zBNC and D-sub input connectable to any source compatible to general CRT monitor
zDigital input fully compatible to DVI-D Standard of VESA DDWG
zChain of Power just one level through power output totally

Issued Date
Revision Status
Title Page No.
7 / 39
V2.8 2008-07-31
RDP2010UX
(AL20SUX)
1. TECHNICAL SPECIFICATIONS
1.1 ELECTRO-OPTICAL SPECIFICATIONS
1.1.1 Screen Specifications
1.1.1.1 Panel Technologies
AMLCD (Active Matrix Liquid Crystal Display) technology
Amorphous silicon TFT (Thin Film Transistor) technology
1.1.1.2 Screen Dimensions
Aspect ratio 4:3
Active screen size:
408 (H) x 306 (V) mm (16.06” x 12.04”)
510.5 mm (20.1”) diagonal
1.1.1.3 Display colors
16,777,216 true colors (8-bit), 256 grey scales
1.1.1.4 Resolution
1600 (H) x 1200 (V) pixels
Pixel arrangement: RGB (Red dot, Green dot, Blue dot) Vertical Stripe
Pixel pitch: 0.255 (W) x 0.255 (H) mm
1.1.1.5 Display mode
Normally Black
1.1.2 Optical Characteristics
1.1.2.1 Protective Filter Glass
Clear, Strengthening glass
Anti Reflective Film and Anti-Static Treatment
1.1.2.2 Luminance (Brightness)
280 cd/m² (typ. typical on LCD)
200 cd/m² (max. typical on Protective Filter Glass)
200 cd/m² (max. typical on touch screen)
Dimming Ratio: 1000 to 1
White uniformity: 75% max.
1.1.2.3 Contrast ratio
700 : 1 (typical on LCD)
1.1.2.4 Viewing Angle: At the contrast ratio > 10:1
Horizontal: +/- 89°(typical)
Vertical: +/- 89°(typical)
1.1.2.5 Response time @ 25°C ambient
Tr : (White →Black)
Td : (Black →White)
Tr + Td : 16 ms (typical)

Issued Date
Revision Status
Title Page No.
8 / 39
V2.8 2008-07-31
RDP2010UX
(AL20SUX)
1.1.3 Input Signal Specifications
RDP2010UX provides maximum four (4) input signal interfaces, 2 x Analog (BNC,D-sub) Input ,1x Digital Input
and 1x Composite video Input.
Standard input resolution is UXGA (1600 x 1200 pixels)
Other resolutions are supported as specified below. No scaling is provided for input signals with resolutions
less than the standard input resolution 1600x 1200 pixels.
Resolution Hsync
(KHz) Vsync (Hz)
VGA 640 x 480 31.0 - 43.0 60.0 - 85.0
SVGA 800 x 600 35.0 - 53.7 56.0 - 85.0
XGA 1024 x 768 48.4 - 68.3 60.0 - 85.0
SXGA 1280 x 1024 64.0 – 91.2 60.0 - 85.0
UXGA(analog) 1600 x 1200 75.0 – 93.8 60.0 - 75.0
UXGA(digital) 1600 x 1200 75 60.0
1.1.3.1 Analog Input
Analog RGB input signal shall be as follows:
Video Signal Level: 0.714 Vp-p nominal
Video Signal Polarity: Positive (Black to White). Polarity is detected automatically.
Both 0 V to +0.714 Vp-p and -0.714 V to 0 Vp-p is allowed.
Video Input Impedance: 75Ωterminated (RGB Video Signal)
Sync: TTL voltage levels, External Separate H & V Sync.
Interlace: Non-interlaced
1.1.3.2 Composite Video Input
Color system : NTSC,PAL,SECAM
Signal Connector : BNC
1.1.3.3 Input Selection
In case multiple input source is connected, input to be displayed can be selected by:
Manual: Operator can select the input manually using control panel.
1.1.4 Controls of the Display
1.1.4.1 Remote Control via serial ports (JH Communication compatible)
There are serial ports on the back side of the RDP2010UX for remote control of the monitor by customer
application.
RS-232/422/485 port: D-Sub, 9p, Female (for JH protocol)
1.1.4.2 Control via OSD
Control block with the push buttons is available: Menu, Select, ◀ and ▶ . Settings are selected by the Menu
that guides you through the OSD menu.
Control block also has ◀ and ▶for dimming brightness.
Control block also has LED indicators, refer to 1.1.5.

Issued Date
Revision Status
Title Page No.
9 / 39
V2.8 2008-07-31
RDP2010UX
(AL20SUX)
1.1.5 LED Indicator
Fault information in available by LED indicators
Normal : Green indicator
Soft Power Off: Amber indicator
No signal : Amber Blinking (every 1 second) indicator
System Fault : Red indicator
1.1.6 Power Supply Specification
1.1.6.1 Voltage range
Standard :100 –-240Vac(Normal), 47~63Hz,1.7A
Voltage Range :AC 100 - 250V
1.1.6.2 Power consumption
Normal
Max. (100% Light output)
RDP2010UX 70 W 75W
1.1.6.3 Power variation protection
Unit will not be damaged when Voltage transients remain within value as defined in the applicable voltage
range
1.1.6.4 Over-temperature protection
When the internal temperature gets above than the warning level (65℃), the light output of the backlight is
half. And, LED as red color
When the internal temperature reaches above the critical Value (80℃), the light output of the backlight is
turned off.And, LED as red color
When the internal temperature gets below than the safe level (64℃), the light output of the backlight is
restored. And, LED recovers to green.
1.1.7 Connectors
1.1.7.1 Power connectors
Standard: IEC type connector
MIL MS-3100F10SL-3P (option)
1.1.7.2 Input signal connectors
Analog Input : 5 Coaxial BNC connectors for R, G, B, HS and VS
D-Sub 15pin connector
Digital input : DVI-D connector
Composit video input (option) : BNC connector
1.1.7.3 Interface connectors for remote control
RS-232/422/485 port: Sub D, 9p, Female (for JH protocol)
Touch screen serial control (Option): 9p Dsub female

Issued Date
Revision Status
Title Page No.
10 / 39
V2.8 2008-07-31
RDP2010UX
(AL20SUX)
1.1.8 Connection & PIN Assignment
Power Input / output
MIL Power Input / output(option)
Analog Input (BNC)
Analog Input (D-Sub)
Video Input (BNC) ( option )
●AC 100-250V, 47~63Hz
with double pole / neutral fusing, 250V F3.15AL
●Disconnect power before changing fuse
●Chain thru power output to limit to one level totally
●R : Analog Red Signal Input (0.7 Vpp, 75 ohm)
●G : Analog Green Signal Input (0.7 Vpp, 75 ohm)
●B : Analog Blue Signal Input (0.7 Vpp, 75 ohm)
●HS : Horizontal Sync Signal Input (TTL)
●VS : Vertical Sync Signal Input (TTL)
●Connection Type : 5 x BNC
●Connection Type : 15p D-Sub Female (Analog only support)
1. Red
2. Green
3. Blue
4. Ground
5. DDC Ground
6. Red Ground
7. Green Ground
8. Blue Ground
9. back up
10. sync Ground
11. Ground
12. DDC Data
13. H sync
14. V sync
15. DDC Clock
● CVBS : Composite Video Signal Input
(1.0 Vpp / Sync.negative, 75 ohm)
●MIL MS-3100F10SL-3P
●AC 100-250V, 47~63Hz
1. A: Live(hot) line
2. B: Ground
3. C: Neutral line

Issued Date
Revision Status
Title Page No.
11 / 39
V2.8 2008-07-31
RDP2010UX
(AL20SUX)
Digital Input
Serial Interface
Touch Screen Serial Control(option)
D-sub
●Connection Type : DVI-D Female (Digital only support)
1. TMDSData2-
2. TMDS Data 2+
3. TMDS Data 2/4 Shield
4. TMDS Data 4-
5. TMDS Data 4+
6. DDC Clock
7. DDC Data
8. No Connection
9. TMDS Data 1-
10. TMDS Data 1+
11. TMDS Data1/3 Shield
12. TMDS Data 3-
13. TMDS Data 3+
14. +5V power
15. Ground (Return for +5V)
16. Hot Plug Detection
17. TMDS Data 0-
18. TMDS Data 0+
19. TMDS Data 0/5 Shield
20. TMDS Data 5-
21. TMDS Data 5+
22. TMDS Clock Shield
23. TMDS Clock+
24. TMDS Clock-
C1 ~ C5 : No Connection
●Remote In(female)
1. No connection
2. RxD (for RS-232)
3. TxD (for RS-232)
4. TxIN_- (for RS-422/485)
5. RxIN_- (for RS-422/485)
6. No connection
7. Ground
8. TxIN_+ (for RS-422/485)
9. RxIN_+ (for RS-422/485)
●Touch screen serial control(female)
1. DCD("carrier detect", handshake='0'
(POSITIVE) when controller power on)
2. RXD (serial data from controller to host)
3. TXD (serial data from host to controller)
4. DTR ("data terminal ready", handshake='0'
(POSITIVE) when controller may send )
5. SG (signal ground)
6. DSR ("data set ready", handshake='0'
(POSITIVE) when controller power on)
7. RTS ("ready to send", handshake='0'
(POSITIVE) when controller may send)
8. CTS (used as "ready to receive", handshake='0'
(POSITIVE) when host may send)
9. RI (not used)

Issued Date
Revision Status
Title Page No.
12 / 39
V2.8 2008-07-31
RDP2010UX
(AL20SUX)
1.2 MECHANICAL SPECIFICATIONS
1.2.1 Dimension and Weight (Rack Mount )
The dimension of the unit is as shown in the table below:
Monitor only Packing
Height (mm / inch) 399 / 15.70 661/26.02
Width (mm / inch) 482 / 18.97 701/27.60
Depth (mm / inch) 125.5 / 4.94 377/14.84
Weight (kg / lbs) 11 / 24.25 18.5/40.79
The following figures show a Rack Mount version mechanical dimension. RDP2010UX basically provides three
input connectors and all connectors are located the bottom side of monitor.
< Front View : Unit mm >
<BottomView>

Issued Date
Revision Status
Title Page No.
13 / 39
V2.8 2008-07-31
RDP2010UX
(AL20SUX)
<RearView>
< Side View : Unit mm>
1.2.2 Mounting
The weight for the unit shall not exceed 11 kg (24.25 lbs)
zFixing: using 4 captive M6 bolts in front bezel
zRDP2010UX can be Standard rack mounted with an optional adapter plate

Issued Date
Revision Status
Title Page No.
14 / 39
V2.8 2008-07-31
RDP2010UX
(AL20SUX)
1.2.3 Finishing
zStandard Bezel color is Black (Rack Mount Type)
zOther bezel colors can be made available on request
1.2.4 Screws/Bolts
zNumber of screws to use for maintenance: reduced to minimum
zType of screws requires maximum 3 standard tools
1.2.5 Components
Industrial extended temperature range components are used for cost, maintainability and reproducibility
purposes.
1.2.6 Cooling
The Unit does not need any forced air-cooling
1.3 ENVIRONMENTAL SPECIFICATIONS
1.3.1 Temperature, Vibration, Shock, Humidity(Except touch screen model)
# item spec Details cycle
1 High temp., Storage MIL-STD-810F,Method 501.4 Procedure I 7
2 High temp., Operating MIL-STD-810F,Method 501.4 Procedure II 3
3 Low temp., Storage MIL-STD-810F,Method 502.4 Procedure I 3
4 Low temp., Operating MIL-STD-810F,Method 502.4 Procedure II 1
5 Humidity MIL-STD-810F,Method 507.4 Procedure I 10
6 Vibration MIL-STD-167-1 Type I -
7 Shock MIL-STD-810F, Method 516.5 Procedure I -
1.3.2 EMC(Except touch screen model)
# item spec details
1 Conducted Emission, Power Lead CE 102 10KHz to 10MHz
2 Conducted Susceptibility, DC and AC Power Leads CS 101 30Hz to 150KHz
3 Conducted Susceptibility, Bulk Cable Injection CS 114 10KHz to 200MHz
4 Conducted Susceptibility, damped sinusoidal transients,
cable and power leads CS 116 100KHz to 100MHz
5 Radiated Emission, Magnetic Field RE 101 30Hz ~ 100KHz
6 Radiated Emission, Electric Field RE 102 10KHz to 18GHz
7 Radiated Susceptibility, Magnetic Field RS 101 30Hz to 100KHz
8 Radiated Susceptibility, Electric Field RS 103 2MHz to 40GHz
1.3.3 Drip-proof
zFront side is drip-proof. Test shall be done when the unit is mounted in a console.
Front bezel: IP64

Issued Date
Revision Status
Title Page No.
15 / 39
V2.8 2008-07-31
RDP2010UX
(AL20SUX)
1.4 OHTER SPECIFICATIONS
1.4.1 Maintainability
MTTR (Mean Time Between Repair)
zRDP2010UX is defined as a Line Replaceable Unit (LRU) and the unit is designed to allow for an MTTR
less than 0.5 hour (30 minutes).
zUse of maintenance equipment
A modular design is taken for the unit. No special tools or equipment are required for maintenance
purpose.
1.4.2 Use of toxic materials
Cold Cathode Fluorescent Lamp (CCFL) in the backlight assemblies contains a small amount of mercury.
The backlight assembly is placed inside of the monitor and is not exposed to user.
1.4.3 Packing
The unit shall be packaged for international transport by air freight in accordance with best practices for insuring
arrival at customer site in an undamaged condition.

Issued Date
Revision Status
Title Page No.
16 / 39
V2.8 2008-07-31
RDP2010UX
(AL20SUX)
2 User Controls
2.1 Operation
POWER ON AND OFF
Power ON: To turn the display on, press the soft-power switch. The LED indicator will turn green.
Power OFF: To turn the display off, press the soft power switch for 5 seconds. The LED indicator will be
turned Amber color.
DISPLAY DIMMING CONTROLS
This TFT display features a fully dimmable image, which means it is capable of displaying a completely
Black image when the Brightness “◀and ▶” is pushed fully to counter-clockwise.
LED INDICATOR DIMMING
The LED light intensity is adjusted with the backlight.
HOT KEY
The user can assign various display function as hot keys
Hot Key1 is able to directly source change. Press the “SELECT”.
Hot Key2 is able to directly auto adjustments in Analog. Press the “MENU” and ”SELECT” for 5 seconds.
Hot Key3 is able to directly adjustments Color. Press the “◀” and “▶” for 5 seconds.
Soft Power Switch
LED indicator
Up/Increase
MENU SELECT
Down/Decrease

Issued Date
Revision Status
Title Page No.
17 / 39
V2.8 2008-07-31
RDP2010UX
(AL20SUX)
2.2 USER Control Access
1: Press the ”MENU” button. The OSD menu will show all the available functions you can
adjust or control.
2: You can move to the next icon by pressing “◀and ▶”.
3: Select options within icon menu by pressing “SELECT” button. The select option will turn yellow.
4: Use “◀” or “▶” button to decrease/increase values.
5: Move the selection left or right by using “◀” or “▶” button. The selected option will turn blue bar.
6: You can exit the pressing “MENU”.
2.3 OSD(ON SCREEN DISPLAY) Navigation
The description below is how to operate the control functions via OSD. The following is the initial OSD menu
displayed by pressing “MENU”. It looks like the general computer monitor, so it is more users friendly.

Issued Date
Revision Status
Title Page No.
18 / 39
V2.8 2008-07-31
RDP2010UX
(AL20SUX)
2.3.1 Adjustment
The “Adjustment” menu is for controlling the brightness, contrast, positions, sharpness, clock and phase.
3.3.1.1 BRIGHTNESS
The function is able the user to adjust brightness for the display, 50 is default value.
“Brightness” adjusts the light output by controlling the opening of Liquid Crystal, it is different from “Dim
Brightness” which is adjusted by controlling the amount of light of backlight directly. But their effects are very
similar. Its adjustment range is -127 to +127. The closer to -127 it is, the darker it is and the closer to +127 it is,
the brighter it is. When one of the submenu of “Adjustment” is selected, the select button push to select it., so
that adjusts the values of the brightness. When the menu button is pushed , going back to the upper menu.
To adjust the brightness is to remap the input data to output data in terms of black and white level. It is to
change the range of data, it means that if the brightness is 127, input data 0 - 255 is remapped to output data
127 – 255, so it looks like brighter. On the other way, if the input data is remapped to 0 – 127, it’ll be darker. It is
to remap the data to LCD panel newly, but it is not to change the real input data. The brightness adjustment
acts on the displayed image of all input data - R, G, and B by the same level.

Issued Date
Revision Status
Title Page No.
19 / 39
V2.8 2008-07-31
RDP2010UX
(AL20SUX)
3.3.1.2 CONTRAST
3.3.1.3 H.POSITION
The function is able the user to adjust contrast for the display, 50 is default value.
“Contrast” is the submenu of “Adjustment”, which sets up the gain of output video signal to panel. Its
adjustment range is 0 to +100. When one of the submenus of “Adjustment” selected, the select button push to
select it. so that adjust the values of the Contrast. When the menu button pushed, going to the upper menu.
To adjust the contrast is to remap the input data to the output data in terms of white level only. It means that if
the contrast is max. 100, input data over 127 is mapped to 255, so, the depth between black and white is
expanded. On the other way, if it is min. 0, input data 0 – 255 is mapped to 0 – 127, so, the depth is reduced.
The contrast adjustment acts on the displayed image of all input data - R, G, and B by the same level. And it
also controls the data to panel, but it does not adjust the input signal.
The function is able the user to adjust horizontal position of image
“H-Position” is the submenu of “Adjustment”, which controls the horizontal position of image, Its adjustment
range is 0 to +100 and default is 50. When the H-position of the submenu of “Adjustment” is selected, the
select button push to select it. so that adjust the values of the H-position. When the encoder switch pushed ,
going to the upper menu.
Adjusting the “H-position” shifts the horizontal position of image. If the value of “H-position” is increased or
decreased by pressing “◀and ▶”, the “H-position” shifts to the right or to the left.

Issued Date
Revision Status
Title Page No.
20 / 39
V2.8 2008-07-31
RDP2010UX
(AL20SUX)
3.3.1.4 V.POSITION
3.3.1.5 SHARPNESS
The function is able the user to adjust vertical position of the display.
“V-Position” is the submenu of “Adjustment”, which controls the vertical position of image, Its adjustment
range is 0 to +100 and default is 50. When the V-position of the submenu of “Analog adjustment” is selected,
the select button push to select it. so that adjust the values of the V-position. When the encoder switch
pushed , going to the upper menu.
Adjusting the V-position shifts the vertical position of image. If the value of “V-position” is increased or
decreased by pressing “◀and ▶”, the “V-position” shifts the upper or the lower.
The function is able the user to adjust sharpness for the display
Closer to 0 Original Closer to 100
“Sharpness” is for making a clear image. Its adjustment range is 0 to +100. When it is 100, the image is the
most clear. When it is closer to 0, the image is blurred. This is not the absolute value on all signals. It may
differ from every signal because the original source quality is very various. If the original signal is good
quality, the image may be looked rather artificially than clearly in max. value 100. In this time, the value
should be adjusted to lower value. If the original source is poor quality, the image becomes clearly more by
adjusting closer to 100. The default value is 50.
Note: This is just for analog signal, and on digital, this function will be disabled.