Wideye ISAVI ISATHUB User manual

PLEASE READ THIS GUIDE CAREFULLY BEFORE ATTEMPTING TO OPERATE THE
ISATHUB.
ISAVI ISATHUB QUICK START GUIDE
Your Satellite Telephone Number is: (supplied at time of delivery)
Your Wi-Fi Password is: TBD (all letters upper case)
The Wi-Fi SSID is TBD
Setup
1. If you are using a smartphone or tablet, install the two free
Isathub Apps from the Appstore or your Android store (IsatHub
Control & IsatHub Voice).
If using a PC, you will use a bowser to connect to the Isathub user
interface. More about this later.
2. Power up the iSavi by depressing the On/Off Button firmly until the
pointing LEDs turn green.
3. Set the terminal outside facing upward to allow the unit to acquire
a GPS position fix. You will see three green point lights flashing
sequentially while the GPS fix is being acquired. This may take up
to five minutes in a new location.

4. Point the iSavi as described by the flashing green Pointing LEDs.
(tip up and down and pan left or right). Once all four Pointing LEDs
are solid green press the Pointing Button. The ISavi is now
connected to the Isathub network (but not yet connected to the
internet, and not using you data allotment).
5. At this point any smart device connected to the iSavi Wi-Fi can
make voice calls using the Isathub Voice app.
Connecting to the Internet w/ Smart Device
1. Connect your device to the iSavi Wi-Fi hotspot using the standard
Wi-Fi connection process. The Wi-Fi password can be found on the
back of the iSavi terminal and at the top of this instruction sheet.
2. Once connected to the iSavi Wi-Fi, use the control app to register
and/or make and break data connections.
3. You will use the following credentials from the Isathub control app
login to the iSavi (this is not the Wi-Fi Password):
Username: admin
Password:1234
4. Once the terminal is registered, you can you the voice app to make
and receive voice calls.
5. Once the data connection is completed, all connected devices can
use the internet via the satellite connection.
6. Be sure to disconnect data when an internet connection is not
required. Also, if using a PC, be sure to deactivate any automatic
software updates on your PC.

Connecting to the Internet w/ a Wi-Fi PC
1. Connect your PC to the iSavi Wi-Fi hotspot using the standard Wi-
Fi connection process. The Wi-Fi password can be found on the
back of the iSavi terminal and at the top of this instruction sheet.
2. Once connected to the iSavi Wi-Fi, use the Web Page based control
page to register and/or make and break data connections as
follows: Open a browser and enter the following IP address into
the address box: 192.168.1.35. This will take you to the web
console.
3. You will be asked for a Username and Password. Use the following:
(this is not the Wi-Fi Password):
Username: admin
Password:1234
4. After logging in you will be taken to the Home page, where you
can see the signal strength, battery level, registration status and
data connection status:

7. If the device is not yet registered with the network, click “Register
Network”. Wait while the terminal registers.
8. Once registered, the terminal is ready to send and receive text
messages. Use the SMS tab for these operations.
9. After registration is complete, you will see the following data on
the Home page. Once the data connection is completed, all Wi-Fi
connected devices can use the internet via the satellite connection.
10. At any time the data usage can be checked by navigating to
the Data Tab.
11. Be sure to disconnect data when an internet connection is
not required. Also, if using a PC, be sure to deactivate any
automatic software updates on your PC.

Call out using the Voice App on Smart Phone
Dial (00) + (Country Code) + (Phone Number) Example: If you want
to dial 1-510-923-9123 you would dial 00-1-510-923-9123 and press
the “phone” button at the bottom of the dial pad. (please note: The
country code for the United State is ALWAYS “1”).
Call in to the Voice App on Smart Phone
Direct Dialing. This is a International call. From the USA, please dial
(011) + (iSavi phone #). Call charges to the phone are paid by the
originator (call charges vary widely from $2.00 to $7.00 per minute,
please contact long distance carrier for specific rates). The user of
the iSavi terminal phone is not charged for this type of call.
Texting out using the Voice App on Smart Phone
Text to 001 + (area code) + (number). Example: 001 504-
512-5555. Your recipient can reply to your text directly in
the normal manner.
Texting to the Voice App on Smart Phone
You can text to the iSavi terminal for free from the following
Inmarsat website. You will see a SMS widget as shown:
http://connect.inmarsat.com/Services/Land/IsatPhone/SMS/
sms.html
Users can text from an IOS device using iMessage by texting
to “+”( iSavi phone number). Example: [phone].
Turn iMessage on and “Send as SMS” off on the IOS device.