Wiiboox WiibooxSweetin User manual
Operating light
Touch screen
Tray
Power switch
Cartridge slot
USB
Power port
FRONT BACK
Preparation
1
Please complete thefollowing steps before turn it on
Note: Customer can upload image through this URL or QR code
2
3
4
5
①Please take out the protecting foam from position A
Please conncet to the electricity (As shown in figure 2 ）
Please install
Connect WiFi
Obtain the unique machine URL and QR code under
Settings Interface
figure 2
AProtecting foam figure 1
Attention: Please stuffback the protecting foam before transit
（As shown in figure 1）
Introduction
Usage
1
2
3
Upload image simply by scanning QR code
or input URL.
Select the image and adjust the cup size, image
brightness and contrast.
Create high resolution image or text in seconds onto
your favorite frothy beverages,both hot and cold.
Maintenance
Put the new cartridge into soltTake out the cartridge from slot
Cartridge slot Put the new cartridge into solt
Turn on
1 2 3 4 5
6 7 8 9 10
Take out PE foam Plug in power Connect wifi
Scan QR code,
upload image
Choose image Place the cup full of drinks
on the tray
Click Printing Finshed
( after " Please wait......")
Instructions
Take out the ink cartridge,
enter the SN code and
tear off the blue ribbon.
ink cartridge
1.Replace ink cartridge
Each ink cartridge can print about 800 cups. You can replenish it
from WiibooxSweetin Amazon Store.
2.Daily maintenance of cartridge
Please wipe the nozzle of the cartridge with a clean and moistened
paper towel before daily use to prevent blockage.
WiibooxSweetin Coffee Printer User Manual
Product parameters
Special instructions
Transportation
In use
1. To avoid damage during transportation, make sure the machine is completely turned off and the protecting
foam is correctly installed.
1. At emergence of an unusual sound, collision, please
switch off the device at once.
Product model Electric parameters
Cup height
Cup diameter
Outline size
Net Weight
Network parameters WiFi 802.11b/g/n Operating power
33cm x19cm x 44cm
AC 110V ~240V 50/60Hz
5cm ~ 24cm
4cm ~10cm
12W
8.6kg
Latte
3. Please put the cup in the center oftray, to make the
pattern at the cup center.
Power Supply
Setting
1. It can not print if the do not install
correctly.
2. Please ensure to place the appliance on a hard,
flat level surfac
e.
Warranty
Restrictions in use
Do not use under the below situations , to avoid electric shocks, fire or other damage
1. Easy to dump and other unstable place
Warranty terms
No-warranty terms
1. Expired warranty
2. Damages caused by force majeure
3. Violations against warranty, including but not limited to customer induced damage, such as self-repairs, exposure to water,
damage caused by misuse, alternation, failure to comply with product manual, and so on.
2. High temperature and heavy wet place,
such as bathroom
4. Please use the original adapter. The warranty is not extended to any damage caused by using other power cords.
If printing pattern failed with lines, please stop running and take
the ink cartridgex out, then clean the spray-head gently with a
wet tissue, until it can flow the ink smoothly.
Do not use hands or other objects to touch the moving
parts when printing.
ink cartridge
2.
1.
2.
3.
4.
Please do not twist or bend the power cord to avoid breakage in
the cord.
When unplugging the power cord, please grasp and pull the
connector, not the cord.
Please do not connect the cable to the improper socket or other
devices.
4.
5.
6.
Non-professional personnel are prohibited from dismantling and
maintaining the appliance.
Ifthepower cordislost ordamaged, please contact
Please unplug power cord when cleaning the device to avoid
short circuit.
1. Wiibooxsweetin will offer a free firmware upgrade service for lifetime.
2. Wiibooxsweetin will provide a 12 month warranty. During the warranty period, if any quality problem is inspected and confirmed
by the manufacturer, a free replacement or repary service shall be provided.
NANJING WIIBOOX 3D TECHNOLOGY CO.,LTD 丨0086-25-84109995丨www.wiiboox.com丨[email protected]
Other Wiiboox 3D Printer manuals
