Williams-Sonoma LACOURTE NO HUTCH DESK User manual


Date:31‐Mar‐2016www.williams‐sonoma.comPage1of4
Rev: 





























LACOURTE NO HUTCH DESK






Date:31‐Mar‐2016www.williams‐sonoma.comPage2of4
Rev: 
Important Safety Instructions:
Please read all instructions carefully before assembling.
For your safety, assembly by two or more adults is strongly recommended.
Keep instructions for future use.
Use only vendor supplied hardware to assemble. Using unauthorized hardware could jeopardize the structural
integrity of the item.
Pre-assembly:
Remove all parts and hardware from the box and lay out on a clear carpeted or scratch-free work surface, as
this will avoid damaging parts during assembly. The shipping box provides an ideal work surface.
Do not dispose of any packaging or contents of the shipping carton until assembly is completed to avoid
accidentally discarding small parts or hardware.
Use the parts and hardware lists below to identify and separate each of the pieces included.
The illustrations provided allow for easier assembly when used in conjunction with the assembly instructions.
The use of power tools to aid in assembly is not recommended. Power tools can damage hardware and split
wood.
Parts Included:
Hardware Included:
(D)




Bolt
1/4”x1‐1/4”
6x
(E)




Flatwasher
1/4”XØ19x2
12x
(F)




Springwasher
1/4”xØ12X2
12x
(G)




Bolt
1/4”x2‐1/4”
6x
(H)




Allenkey
M4x110x30
1x
Parts Included (Box 1 of 3): Parts Included (Box 2 of 3): Parts Included (Box 3 of 3):
(A)
Desk top
(B)
Right leg frame
(C)
Left leg frame

1x 1x
1x


Date:31‐Mar‐2016www.williams‐sonoma.comPage3of4
Rev: 
Assembly Instruction Steps:
1. Remove the drawer boxes from desk top (A).
2. With the help of another person, carefully place the Desk Top (A) upside down on a clean, smooth surface, such
as a carpet or cardboard
3. Attach the right leg frame (B), left leg frame (C) to (A), by aligning the pre-drilled holes with the wooden
dowels. Insert 6 Bolts (D), 6 Bolts (G), 12 Flat washer (E), 12 Spring washer (F) and tighten the bolts with
Allen key (H), as show below:


Date:31‐Mar‐2016www.williams‐sonoma.comPage4of4
Rev: 
4. Install the drawer boxes back to the Desk top (A).
5. Attached theAnti-tip kit at the back and adjust the levelers underneath the four corners of the base as seen
in the illustration below
Adjusting the Levelers:
If the floor is uneven, the furniture may not sit level and the piece may wobble. If the furniture wobbles, determine
which corner does not touch the ground correctly. With two people follow the steps below:
- Carefully elevate the item slightly, to provide access to the levelers attached to the bottom of each leg.
- Turn the levelers (up or down) until adequate contact will be made with the floor. Gently set the piece down
and check stability.
- Repeat the steps above, until furniture sits firmly on the ground.
6. Assembly is complete.
Care Instructions:
Dust often using a clean, soft, dry and lint-free cloth.
Blot spills immediately and wipe with a clean, damp, cloth.
We do not recommend the use of chemical cleansers, abrasives or furniture polish on our lacquered finish.
For glass tops and shelves, glass cleaner may be used, but avoid spraying it onto the metal or ceramic
frame.
Hardware may loosen over time. Periodically check to make sure all connections are tight.
Re-tighten if necessary.
Thankyouforyourpurchase
Stores | catalog
